WEINIG RAIMAN PROFIRIP 450M And Combiscan EVO Luxscan Lumber Scanner SystemThe system is complete with: -- (1) Weinig lateral lumber feeder table to scanner head -- 12" wide rubber belted infeed -- Roller/Sweep type lateral conveyor with sequencing and buffer to scanner infeed -- (1) Weinig CombiScan EVO Luxscan Line Feed through lumber scanner -- Model CombiScan EVO -- Max width 310 mm (12.2") -- Min width 25 mm (0.984") -- Max length 6500 mm (255.9") Min length 900 mm (35.4") -- Max thickness 100 mm (3.93") -- Min thickness 12 mm (0.472") -- Speed range 80 to 300 m/Min (up to 250 boards/min) -- Max throughput 200 m/Min -- Luxscan combiscan EVo R with two cameras, top-bottom (2 side detection laser cameras, 2 side detection color defect high-resolution cameras, 2 side detection with dot laser, 2 side line scatter, angle crack detection 2 side) -- Freestanding operator computer control station -- Flat screen color display with keyboard -- Opticore direct controls -- Freestanding electrical and computer control cabinet -- Freestanding chiller unit for laser system -- Scanner infeed and outfeed table system -- Safety guards with access doors around the scanner and rip line machines -- Includes the machine operators' manuals -- (1) Weinig sweep type lateral conveyor table from scanner to the rip sequencer table -- Chain deck type sequencing and spacing conveyor table -- Infeed rip saw board flipper with servo fence system to rip saw -- (1) Weinig Raimann ProfiRip 450M Gang Rip Saw With (2) Movable blade -- 51 kW, 460 V, three-phase, 60 Hz -- Max cutting width 450 mm (17.7") -- Max cutting height (with 450 mm diameter blade and without pressure board) 150 mm (5.9") -- Max cutting height (with 450 mm diameter blade and with pressure board) 135 mm (5.31") -- Min. cutting thickness: 15 mm (0.59") -- Min cutting length 780 mm (30.7") -- Chain width 470 mm (18.5") -- Diameter of saw arbor 65 mm (2.55") -- Min blade diameter 300 mm (11.8") -- Max blade diameter 450 mm (17.7") -- Saw blade bore 80 mm (3.14") -- Arbor speed 3900 RPM -- Feed speed range: 15 to 120 m/Min -- Machine weight 4500 Kg (9920 Lbs) -- Saw drive motor 45 kW, 460 volt three phase -- Feed motor 4 kW, 460 V, three-phase -- (1) Fixed and (2) movable saw blade design -- Edging removal system -- Sound and safety machine enclosure -- Front access door with inspection window and safety interlock -- Freestanding operator computer control station -- Pro-Face color touch screen display -- Joystick movable blade controls -- Freestanding electrical control cabinet -- Includes the machine operator's manuals -- (1) Weinig rip saw outfeed table with lateral feeder to chop saw station -- Outfeed roller/sweep type conveyor -- Cross conveyor table with servo accelerator -- Freestanding operator conveyor system controls (zone ripping)Note: System installed new in 2019 and sells for a fraction of new.

WEINIG - VALU-RIP: Infeed Conveyor System for Rip Saw Specifications -- 7-Chain Deck; spaced at: 0", 25", 54", 75", 96", 120", 147". -- (5) Board stops on Chain Deck. -- Roller Deck with: (7) Drop chains. -- (8) 50" Rollers; powered by: 2 HP Motor. -- Drop Chains spaced at: 0", 36", 54", 72", 110", 147", 181-1/2". -- Automatic Saw Fence with: TISFOON Scanning System. -- Powered Pinch Roll before Saw: 2 HP Motor.NOTE: This is part of a Total Plant Liquidation; please call for details!

WEINIG - UNIMAT 10005-Head (B-R-L-T-B), 9-1/16" x 4-3/4" cap. -- Head sequence: Bottom 10 HP; right 15 HP; left 15 HP; top 25 HP; 20 HP motor. -- WEINIG "Memory Re-Dial" System with: Storage of (100) separate profiles; electronic LED readouts for all spindles. -- Spindle dia. 1-13/16" with Cutterhead speeds: Spindle #1 at 6,000 RPM; spindles #2 - #5 at 7,000 RPM with high precision bearings & mechanical spindle brakes; adjustment of vertical spindles 3-1/8" axially. -- Electronic LED readouts for: Chip breaker & pressure elements for top spindles. -- Cutting circles: 8-7/8" On spindles #2 - #5; vertical spindles with adjustable table plates to cutting circles; hardened infeed bed plates before-and-after 1st bottom head. -- Motorized feed beam adjustment; variable feed speed from: 20 - 118 FPM; 10 HP inverter controlled Cardan feed drive, overhead feed wheels with pneumatic pressure. -- (1) Powered table roller in bed at outfeed. -- Infeed straightening table 2 M (6-1/2') with adjustable fence; adjustable table at outfeed. -- Equipped with: Central location of lubrication points; side pressure roller at infeed; manual Waxilit pump; (2) lights inside sound enclosure. -- Includes Set-Up Stand.NOTE: Machine is in good running condition, but electric brakes are not functional; does not affect running or performance.

WEINIG UNIMAT 23 ATS, 6 HEAD MOULDER6-Head (B-R-L-T-T-B), working capacity 9-1/16" x 6" profiling. -- Head sequence: Bottom 10 HP, right & left by 15 HP, top 20 HP, top 15 HP and bottom 15 HP motor; Spindle dia. 40 mm with cutterhead speed of 6,000 RPM. -- WEINIG ATS (Automatic Tool Setting), Storage for up to (99) profiles; automatic positioning (radially) of left and top spindles (linked). -- Mechanical digital readouts on all other spindle adjustments for both axis, radial adjustment only on 1st bottom head. -- Motorized feed beam adjustment with independent adjustment of top heads, Receding chip breakers on left and top heads. -- Feed motor 7.5 HP, variable speed 18 - 118 FPM, overhead feed wheels with pneumatic pressure, (2) powered rollers in machine table. -- Large tool cutting circles, table plates adjustable to the cutting circle on vertical spindles with axial adjustment of 3-1/8" for multiple profiles. -- Infeed straightening table 2 M (6'6") with adjustable fence & adjustable outfeed table. Side pressure roller mounted to infeed table. -- Includes: Central lubrication, full sound/safety enclosure, manual bed lubrication pump.

Wood Pellet Manufacturing Plant Equipment;Complete with the following features: -- Design capacity 15 tons per hour. -- (1) Pellet Mill (Pellet Press) – custom built in USA and was producing at a rate of 4½ tons per hour. Comes complete with spare parts. -- WEST SALEM Model 4-4-60S Hammer Mill. -- Bulk storage. -- Conveyors to bagging system. -- Blowers Cyclones & Piping.NOTES: Plant was planned for several pellet mills but was shut down due to lack of sales. Operated only 3-4 years but has been down for a few years now. All equipment remains installed. Wood supply was from several sources: processing plants by-product, shavings from planer mills, finger jointing plant, and ground trim blocks. No Dryer - Owner using it. More details on request. Professional rigging is available.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i61 WHIRLWIND 1000 L Upcut Saw Specifications: 2-3/16" x 8-1/4" Cap., 14" blade cap., 3,450 RPM, left-hand unit feeding from right-to-left, 5 HP BALDOR motor. Complete with: (5 - 90) Cycles/Min; magnetic starter with low voltage controls, air filter, regulator, coalescing filter, and 4" dust chute. NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

WHITFIELD 43-1C-43 Wide Belt Sander (4) Heads52" wide belt with Steel drum, Rubber drum, Rubber drum and Combi headSpecifications: -- Maximum working width 52" -- Maximum working height 5" -- Heavy-duty structure with base consisting of a cast iron base integrated with stress-relieved steel to ensure machine rigidity and flatness -- The bottom transfer bed is, guided on re-circulating guides and driven by 4 precision ball-screws to ensure a perfect flatness of the working bed.FEEDING SYSTEM -- Bottom rubber vacuum belt driven by hydraulic motor to ensure consistent feed speed as load varies. -- Vacuum suction unit with 7.5 HP motor and noise dampening silencer -- Infeed safety switchMachine configured as follows: Pos.1- -- Steel Drum 300mm diameter x 1350mm length -- 40HP auto oscillating belt with through beam sensors to control belt tracking. -- Lead in and lead out hold down shoes -- Dust collection at exit of belt -- Belt brake switch -- Mechanical braking -- Belt cleaning with oscillating air blow off -- Belt Size 54" x 103" Pos.2 - -- Rubber Drum 300mm diameter x 1350mm length -- 40HP auto oscillating belt with through beam sensors to control belt tracking. -- Lead-in and lead-out hold-down shoes -- Dust collection at exit of belt -- Belt brake switch -- Mechanical braking -- Belt cleaning with oscillating air blow off -- Belt Size 54" x 103"Pos.3 - -- Rubber Drum, Inverter driven for control of rotation direction and speed; 300 mm diameter x 1350 mm length -- 30HP auto oscillating belt with through beam sensors to control belt tracking. -- Lead in and lead out hold down shoes -- Dust collection at exit of belt -- Belt brake switch -- Mechanical braking -- Belt cleaning with oscillating air blow off -- Belt Size 54" x 103"Pos.4 -- Combi Head 160mm diameter x 1350mm length -- 25HP auto oscillating belt with through beam sensors to control belt tracking. -- Lead in and lead out hold down shoes -- Dust collection at exit of belt -- Belt brake switch -- Mechanical braking -- Belt cleaning with oscillating air blow off -- Belt Size 54" x 103" --Combi Head 160mm diameter x 1350mm lengthAlso Included: -- Panel Cleaning Brush mounted at Out-Feed --1HP motor -- Dust extraction portControl -- Mitsubishi Touch screen and PLC to control; -- Thickness setting -- Manage 1/0 -- Control Belt Feed Speed -- Head 3 Rotation Direction and Speed -- Display 1/0 for trouble shootingNote: Installed in January 2025 and ran until July 2025

WILLIAMS - C 32 100: HP Hammermill(20) Lbs Hammers: (22) Total Hammers.1" Slot screens.Soft start: Included.Opening: 32" x 19".Video available of operation.32" x 19" Opening.Comes with: 100 HP - 1,800 RPM motor.Includes: Direct drive with Integrated base; infeed chute.

Model 206 For smooth moulding and planing; (1) 2 HP Baldor motor, 7,000 RPM spindle speed, variable feed rate of 1 - 19 FPM includes "Deluxe" variable feed control with magnetic drop out switch and cords. Built in Multi-Pass system and Guide sytem -- Capacity: Max. material width 7", material thickness from 3/4" to 8" max., min. 9" stock length. Max. profile depth 3/4" and max. profile width 6-3/4", planes 7" wide and can do a 7" radius with optional jig; working height 31", overall height 45", overall width 20". -- Includes: Table guides, dust hood, belt, pulley, planing knives, welded steel stand, custom moulding catalog, oil, and operator's manual. -- With OPTIONAL accessories like the elliptical jig you can make arches and elliptical mouldings, please add...$ 700. Also available in 115/1/60 and 230/460V/3/60. Weight: Approx. 242 Lbs.

WILLIAMS & HUSSEY - # 206: Moulder Specifications -- 2 HP - 3,450 RPM motor; 6,900 RPM arbor speed. -- 0 - 19 FPM Variable feed rate. -- Max. profile depth: 3/4". -- Max. profile width: 6 3/4". -- Minimum stock length: 9". -- Minimum stock thickness: 1/4". -- Max. stock thickness: 8". -- Max. height above final cut: 3/16"; max. plane width: 7"; working height: 35".

WILTON 4421-2 DISC SANDER ---Price Negotiable---Make an Offer!--- Heavy Duty for Wood, Metal, Fiberglass, or Plastic! - Pedestal-Type Disc Sander - Table size 10-1/2" x 27-1/2", Table tilt 45° Out/30° In, Table can be lowered below disc to accommodate large workpieces - 3 HP 1,720 RPM Direct drive motor, Low voltage protection switch - Positive lock rack & gear table tilt