NOVA PELLET - N-Eco - 45 kW, ...Pellet Mill Low specific energy consumption per ton of pellet.Specifications: -- Capacity: 770 - 1,200 Lbs/Hr (350 - 550 kG/Hr) depending on the raw material. -- Main drive: 60 HP (45 kW). -- Pellet dimensions: 0.24" - 0.31" (6 - 8 mm) diameter. -- Raw Material: Wood chips, sawdust, wood shavings: 0.02" - 0.06" (0.5 - 1.5 mm) Length; 8 - 14% MC. -- Die: 15" (380 mm) Internal diameter; 0.6" - 2" (14 - 50 mm) long die holes. -- Roller: 7.2" (182 mm) Outer diameter.General specification: -- Pellet Mill with mechanical and electrical functioning system. -- Pellet Mill with (1) die and (2) Rollers. -- Electrical cabinet with: SIEMENS PCL System, touch screen, and remote modem connection. -- High efficiency motors with IE2 standards (Energy Saving). -- Raw material dosing system (frequency controlled). -- Mechanical level sensor for the saw dust hopper. -- Vegetable oil for start and end of production cycle. -- Automatic grease lubrication for rollers and main shaft. -- Electrical safety locks. -- CE conformity certificate.

NOVA PELLET - N-Midi - 90 kW, ...Pellet Mill with low specific energy consumption per ton of pellet. -- Capacity: 1,765 - 2,315 Lbs/Hr (800 - 1,050 kG/Hr) depending on the raw material. -- Main drive: 120 HP (90 kW). -- Pellet dimensions: 0.24" - 0.31" (6 - 8 mm) diameter. -- Raw Material: Wood chips, sawdust, wood shavings; 0.02" - 0.06" (0.5 - 1.5 mm) length; 8 - 14% MC. -- Die: 15.7" (400 mm) Internal diameter; 0.6" - 2" (14 - 50 mm) long die holes. -- Roller: 7.2" (180 mm) Outer diameter.General Specifications: -- Pellet Mill with mechanical and electrical functioning system. -- Pellet Mill with (1) die and (2) Rollers. -- Electrical cabinet with SIEMENS PCL system, touch screen, and remote modem connection. -- High efficiency motors with IE2 standards (Energy Saving). -- Raw material dosing system (frequency controlled). -- Mechanical level sensor for the saw dust hopper. -- Vegetable oil for start and finish of production cycle. -- Automatic grease lubrication for rollers and main shaft. -- Electrical safety locks. -- CE Conformity certificate.

NOVA PELLET - N-Plus - 165 kW, ...Pellet Mill with low specific energy consumption per ton of pellet. -- Capacity: 2.2 - 2.8 Tons/Hr (2.0 - 2.5 metric tons/Hr) depending on the raw material. -- Main drive: 215 HP (160 kW). -- Pellet dimensions: 0.24" (6 mm) Diameter. -- Raw Material: Wood chips, sawdust, wood shavings; 0.02" - 0.06" (0.5 - 1.5 mm) length; 8 - 14% MC -- Die: 22.8" (580 mm) internal diameter; 0.6" - 2" (14 - 50 mm) long die holes. -- Roller: 9.4" (245 mm) Outer diameter.General Specifications: -- Pellet Mill with mechanical and electrical functioning system. -- Pellet Mill with (1) die and (2) Rollers. -- Electrical cabinet with SIEMENS PCL system, touch screen, and remote modem connection. -- High efficiency motors with IE2 standards (Energy Saving). -- Raw material dosing system (frequency controlled). -- Mechanical level sensor for the saw dust hopper. -- Vegetable oil for start and finish of production cycle. -- Automatic grease lubrication for rollers and main shaft. -- Electrical safety locks. -- CE conformity certificate.

NOVA PELLET N-Eco Pellet Plant;Complete Wood Pellet Manufacturing Plant including Dryer and Bagging Line: -- Capacity: 770 - 1,1212 Lbs/Hr (350 - 550 kG/Hr). -- Raw Material: Wood chips, sawdust, wood shavings. -- Power: 174 HP (130 kW) Installed, 148 HP (110 kW) average.The Pellet Plant consists of the following main components: -- Wood Chip Hopper: 110 cu. ft. (3 cbm) volume; includes: Discharge Screw, Motor. -- Rotary Drum Dryer: 770 - 1,100 Lbs/Hr (350 - 500 kG/Hr) dry material capacity, moisture reduction from ...40 - 50% to 14%; includes: Cyclone, Rotative Valve, Electrical Cabinet with PLC. -- Biomass Burner: Approx. 220 Lbs/Hr (100 kG/Hr) Wood Chips, max. ...25% moisture content. -- Magnetic Separator. -- Hammer Mill: 770 - 1,320 Lbs/Hr (350 - 600 kG/Hr) dry material capacity, 40 HP (30 kW) installed power, 0.78" x 0.78" x 0.2" max. grain size. -- Dry Chip Silo: 180 Cu/ft. (5 cbm) volume, 83" (2,100 mm) diameter, 264" (6,700 mm) height; includes: Dust Filter, Pulse Jet Cleaning System, Safety System with Spark detection, Rotative Valve. -- Pellet Mill (Type: N-ECO): 770 - 1.320 Lbs/Hr (350 - 600 kG/Hr) capacity, 60 HP (45 kW) main drive; includes: (1) x Die, (2) x Rollers, Electrical Cabinet with PLC. -- Packaging Line (Type: N-Pack): Manual operated line includes: Vibrating Screen, Conveyors, Storage Hopper, Pneumatic Valve, 15 kG Bags. -- Auxiliary equipment: Conveyors, Ducts for Dedusting, etc. -- Shipping to US port, Mechanical & Electrical installation, start-up, and training included.NOTE: Price and delivery terms will have to be reviewed and confirmed at the time the order is placed.

Complete Wood Pellet Manufacturing Plant including Dryer and Bagging Line. -- Capacity: 0.9 - 1.3 Tons/Hr (0.8 - 1.2 metric tons/Hr). -- Raw Material: Wood chips, sawdust, wood shavings. -- Power: 335 HP (250 kW) Installed, 295 HP (220 kW) average.The Pellet Plant consists of the following main components: -- (1) Wood Chip Hopper: 706 cu. ft. (20 cbm) volume; includes Discharge Screw, Motor. -- (1) Rotary Drum Dryer: 1.0 - 1.2 tons/Hr (0.9 - 1.1 metric tons/Hr) dry material capacity, moisture reduction from ...25% to 12% (Optional: Dryer for higher moisture contents); includes: Cyclone, Rotative Valve, Electrical Cabinet with PLC (Optional: additional Dust Filter). -- (1) Biomass Burner: Approx. 695 Lbs/Hr (315 kG/Hr) Wood Chips, max. ...45% moisture content. -- (1) Magnetic Separator. -- (1) Hammer Mill: 1.0 - 1.4 Tons/Hr (1 - 1.3 metric tons/Hr) dry material capacity, 100 HP (75 kW) installed power, 1.2" x 0.78" x 0.2" (30 x 20 x 5 mm) max. grain size. -- (1) Dry Chip Silo: 565 cu. ft. (16 cbm) volume, 124" (3,150 mm) diameter, 321" (8,150 mm) height; includes: Dust Filter, Pulse Jet Cleaning System, and Safety System with Spark detection, Rotative Valve. -- (2) Pellet Mills (Type: N-MIDI): Each 1,100 - 1,540 Lbs/Hr (500 - 700 kG/Hr) capacity, 74 HP (55 kW) main drive; includes: (1) x Die, (2) x Rollers, Electrical Cabinet with PLC. -- (2) Vibrating Screens. -- (1) Pellet Cooling Column. -- (1) Packaging Line (Type: N-Pack): Manual operated line includes: Screen, Conveyors, Storage Hopper, Pneumatic Valve, 15 kG Bags, semiautomatic Pallet Wrapping machine. -- Auxiliary Equipment: Conveyors, Ducts for Dedusting, Fan for Silo loading, etc. -- Shipment to US port, Mechanical & Electrical installation, start-up, and training included.

NOVA PELLET - N-Plus Plant Complete Wood Pellet Manufacturing Plant including Dryer and Bagging Line: -- Capacity: 1.5 - 2.4 tons/Hr (1.4 - 2.2 metric tons/Hr). -- Raw Material: Wood chips, sawdust, and wood shavings. -- Power: 523 HP (390 kW) installed, 443 HP (330 kW) average.The Pellet Plant consists of the following main components: -- (1) Wood Chip Hopper: 706 cu. ft. (20 cbm) volume; includes: Discharge Screw and Motor. -- (1) Rotary Drum Dryer: 1.5 - 2.0 Tons/Hr (1.4 -1.8 metric tons/Hr) dry material capacity, moisture reduction from ...25% to 12% (Optional: Dryer for higher moisture contents); includes: Cyclone, Rotative Valve, Electrical Cabinet with PLC (Optional: additional Dust Filter). -- (1) Biomass Burner: Approx. 955 Lbs/Hr (433 kG/Hr) Wood Chips, max. 45% moisture content. -- (1) Magnetic Separator. -- (1) Hammer Mill: 1.6 - 2.2 tons/Hr (1.5 - 2.0 metric tons/Hr) dry material capacity, 177 HP (132 kW) installed power, 1.2" x 0.78" x 0.2" (30 x 20 x 5 mm) max. grain size. -- (1) Dry Chip Silo: 1,130 cu. ft. (32 cbm) volume, 154" (3,900 mm) diameter, 476" (12,100 mm) height; includes: Dust Filter, Pulse Jet Cleaning System, Safety System with Spark detection, and Rotative Valve. -- (1) Pellet Mill (Type: N-PLUS): 1.5 - 2.2 tons/Hr (1.4 - 2.2 metric tons/Hr) capacity; 215 HP (160 kW) main drive; includes: (1) x Die, (2) x Rollers, Electrical Cabinet with PLC. -- (1) Vibrating Screen. -- (1) Pellet Cooling Column. -- (1) Double Pellet Bin: 159 cu. ft (4.5 cbm) volume. -- (1) Automatic Packaging Machine: (5) bags/minute capacity; includes: Screen, Conveyors, Storage Hopper, Pneumatic Valve, 15 kG Bags, semiautomatic Pallet Wrapping machine. -- Auxiliary Equipment: Conveyors, Ducts for Dedusting, Fan for Silo loading, etc. -- Shipment to US port; Mechanical & Electrical installation, start-up, and training included.

NOVY 1872V Multi Spindle Vertical Boring Machine 12 Spindles Vertical boring machineSpecifications: -- Table Hardwood 18" X 72' -- Table stroke 0"- 6" -- (12) Spindles in line at 5" center to center, spindle nose with 0" to 1/2" chuck -- (2) drive motor 2 HP with magnetic starter -- (4) Spring loaded hold down -- Savety guard -- Foot swtich

OAKLEY H-5 Double Sided Edge Sander. -- General Specs: With 7.5 HP -1,800 RPM TEFC motor; (2) 8-1/2" x 57-1/2" Cast Iron platens; 8" x 164" abrasive belt, 4,680 FPM belt speed. -- Equipped with: One 11" x 62" Cast iron side table on one side and (1) 19" x 64" cast table on the other side, (1) cast iron radius tilting end table, end table tilts 0 ° - 45°; 6" vertical table travel w/hand wheel adjustment. -- Features: Rubber covered direct drive pulley and idler pulley,Complete with: Magnetic starter with overload protection, (8) dead head radius ends with graphite covering, and (1) steel covered spare head roll.

OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGAM PO/M Straight Line Rip Saw;Specifications: -- 20 HP Main motor. -- 24"; throat capacity. -- Max. cutting height: with 12" blade 3", with 16" blade 4". -- Min. diameter of circular saw blades: 8". -- Max. dia. of circular saw blades: 16". -- Min. length of working pieces: 10". -- Variable feed speed from 50 -154 Ft./minute. -- Feeding belt width: 11". -- Spindle Speed: 4,500 RPM. -- 36"; x 60"; table.Equipped with & Features: -- Fence and rail system with one stop. -- Infeed table row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Top row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Split hold down steel smooth roller around blade. -- Split hold down steel smooth roller around blade. -- Steel smooth top hold down roller. -- Chain is in excellent condition!

OGDEN PUR LAMINATING LINE for Engineered FlooringSystem consists of:POS 1. PLYWOOD HOPPER FEEDER Plywood boards (two-track or single-track) are loaded vertically into the hopper and push-fed from the hopper into the Roll Coater where the rolls from the Coater take over feeding the plywood. The plywood hopper feeder is centered to the press; adjustments of the fence are via hand crank where both sides of the fence move simultaneously. The hand crank has a digital indicator to assist the operator in the width setup. Specifications:Length 4 ft to 8 ftWidth with single track 6" to 12"; tolerance of +/- 1/64";Width with double track 3" to 7" tolerance of +/- 1/64";Hopper capacity height 16";Pass line-height 37"; POS 2. DRUM MELTER Drum melter melts the glue which is contained in a 55-gallon drum, it pumps the glue out through heated hoses and delivers the glue to the roll coater. The roll coater sends the drum melter signals when to pump glue and when to run the pump off, a signal is sent according to glue level height. POS 3. TOP HEAD PUR ROLL-COATER Roll coater to apply hot melt PUR glue to the top of the Substrate. Roll coater will be equipped with wheel casters in order to move the unit out of the line for cleaning. Touch Screen Control panel for the coater is mounted on the left-hand side when facing the in-feed of the unit. Adjustment of doctor roller will be with hand wheel (not powered) and mechanical digital display in increments of 0.001" in relationship to application roller. Adjustment of the coating roller will be powered and will include a hand wheel with a mechanical digital display in increments of 0.001" Roll coater is equipped with a fume extraction hood which is located above the roll coater. Feed speed 20 - 250 FPMMin coater length 21"Maximum thickness 4"Minimum thickness 3/8"Effective coating width 14"Doctor roller ground chromeCoating roller silicone, 60 durometerVoltage 480 VPass line height 37"; POS 4. PLYWOOD TRANSFER CONVEYOR Conveyor length 20’Veneer lengths 2’ to 12’ ’Width with single track 7" to 12"; tolerance of +/- 1/64";Width with double track 3" to 7" tolerance of +/- 1/64";Pass line-height 37";Feed speed range from 20 to 250 FPMPop up gate will be installed to st

OLIVER 5385 Single Head Wide Belt SANDER (37") 1-Head and 37" belt width Combination Sanding Head with rubber covered contact roll and adjustable finishing platen, 1/8" - 5" Thickness capacity, 36" width capacity.Specifications: -- 20 HP Main drive motor. -- 1 HP Variable speed (15 to 45 FPM). -- 1/4 HP Power raising and lowering conveyor bed motor. -- 37" X 75"; Abrasive belts for longer life and less loading.Features; -- Central control panel features digital thickness set-up control for accurate stock height and removal. -- Four post lift design assures accurate consistent results. -- Oscillating belt is controlled by an air sensor to prevent sanding lines. -- Finishing Platen is fully adjustable and can be removed. -- Multiple dust ports for efficient dust management. -- Independent motors run the sanding belt, feed conveyor, and table elevation for maximum power to each operation.

OLIVER 6910 Oscillating Spindle SanderPedestal style Spindle Sander constructed for rugged use .Specifications: -- 2 HP Motor drives and is connected through a flexible coupling, and can be installed or removed without disturbing the drive mechanism. -- Spindle speed 1,725 RPM, Oscillation speed 75 Cy/Min with 1-1/2" stroke length. -- Spindle quill runs in precision ball bearings, oscillated by a heavy duty worm & gear mechanism running in a bath of oil. -- (10) Spindle sizes provided: 1/4 x 5", 3/8 x 6", 1/2 x 6", 5/8 x 6", 3/4 x 9", 1 x 9", 1 1/2 x 9", 2 x 9", 3 x 9" and 4 x 9"; 100 grit abrasive sanding sleeve with each spindle. -- Large 24" x 24" precision ground cast iron table mounted on large trunnions that can be tilted 45° down and 30° up by use of a convenient handwheel. -- Complete with: Pedestal style stand.

OLIVER - 34-DD, ...Disc Sander (Double)(2) 30" Dia. steel discs; 5 HP double shafted motor turns @ 1,050 RPM.(2) Steel side tables, 40" x 15", (1) slotted and (1) plain; both tables tilt 10° up and 45° down.(1) Table with 6" manual vertical adjustment; rack travel adjustment by screw & crank. -- Complete with: Magnetic controls; (2) dust outlets; large handwheels for easy adjustments.

OLIVER 4705 SHAPER 5 HP, Sigle phase or 7.5 HP, 3-PhSpecifications and Features: -- Massive cast iron precision ground table provides a solid work surface. -- Cast iron base provides a steady platform. -- 3/4"; and 1-1/4"; interchangeable spindles are included for added versatility. -- Three spindle speeds allow more choices to produce a better finish. -- Reversing spindle gives more options for each set-up. -- Innovative dovetail design accurately raises and lowers the spindle. -- Fence is independent and features micro adjustments for quick set-up. -- Top mounted control panel includes a digital readout for spindle height. -- Large hand wheel for quick spindle height adjustment. -- Magnetic controls with emergency off switch for safer operation. -- Includes miter gauge. -- Spindle Speeds: 5,000, 7,000 and 10,000 RPM. -- Maximum Tool Diameter: 7"; Below Table, 8"; Above Table. -- Spindle Diameter: 1-1/4"; and 3/4"; Interchangeable. -- Vertical Spindle Travel: 4". -- Table Height: 36-1/2". T-Slot: 3/4" x 3/8". -- Dust Port Diameter: 4". -- 800 CFM min. -- Optional collet for router bits available special order --[1/2" Spindle for Models 4705 & 10047 Shaper]1/2" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[3/4" Spindle for Models 4705 & 10047 Shaper]3/4" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[1" Spindle for Model 4705 Shaper]1" Spindle for Model 4705 Shaper$99.99Model 4705[1/4" Collet for Models 4705 & 10047 Shaper]1/4" Collet for Models 4705 & 10047 Shaper$69.99Model 4705[1/2" Collet for Models 4705 & 10047 Shaper]1/2" Collet for Models 4705 & 10047 Shaper$59.99Model 4705[1-1/4" Spindle for Model 4705 Shaper]1-1/4" Spindle for Model 4705 Shaper$99.99Model 4705 prices may vary.

OLIVER 4455 22" Straight Knife Planer, 5 HP single phase or 10 HP, 3-Ph.The OLIVER "4455" Planer has a super-wide capacity, it'll handle stock up to 22" wide, and takes up to 3/16" off in a single pass.Specifications: -- 4-Knife HSS straight knife cutter head. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on an uneven stock, coupled with a Driven Outfeed Roller to keep your stock moving smoothly. -- Add (2) feed speeds for extra quality, a Digital Thickness Guage for quick reference, and a powerful 10 HP motor. -- Max depth of cut 3/16" min part length 10"; Max work pc 22" w x 9" Thickness.

OLIVER 4470 25" Straight Knife Planer Full 24" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through the 4-knife standard cutter head, this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor. --OPTIONAL EQUIPMENT: Byrd Shelix Cutterhead (ADD $2,400)

OLIVER 4430 20" PLANER WITH HELICAL HEAD20" Maximum stock width cap., 1/4" to 8" max. stock thickness, 10" minimum stock length. Equipped with: -- 5 HP Main drive motor and mechanical raising and lowering of the cutter head. -- Fixed bed height of 29-7/8". Table dimensions 20"L X 21"W. Overall all table dimensions with infeed and outfeed bed extensions 51"L X 21"W. -- 3-1/4" Dia. Helical Cutter Head with 4-sided carbide inserts. -- Auto-Depth lock via nitrogen-charged cylinders eliminates snipping. -- 8" Max. thickness adjustment via handwheel includes LED Digital readout for head positioning. -- 4-Post support for proper head alignment.Complete with: -- 5" Dust outlet and built-in mobile base for ease of movement

OLIVER 4470 25" Shelix Cutterhead Planer; 10 HP motor Single Phase, or 15 HP 3-Phase motor. Full 25" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through , Byrd Shelix Cutterhead this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor.

OLIVER 15" Planer with Helical Cutterhead - 10014, 3 HP (Single Phase)Unique design allows motor and cutter head to move in unison.Specifications: -- Auto-depth lock features twin nitrogen cylinders virtually eliminates snipping. -- Helical cutter head with premium carbide inserts. -- 4-Sided cutting inserts are indexed and easy to replace. -- Heavy cast iron construction including extension wings. -- Table and extensions wings are precision ground for smooth stock feeding. -- Table is fixed allowing easy use of auxiliary stock support. -- Wixey digital read-out allows precise thickness settings. -- Large handwheel and support struts allow easy height adjustment. -- Four-post design ensures head alignment regardless of stock thickness. -- Two-speed feed gearbox for better cuts, Oil bath gear lubrication for years of performance.Complete with: -- 4"; Port allows excellent dust management. -- Built-in mobile base allows easy movement in the shop. -- Magnetic switch for added protection and safety.