This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

VERVILLE 6-SCREW HOLDING BINSpecifications: -- (6) Motorized 14-1/2" Diameter Bottom Screw -- (1) Motorized 14-1/2" Diameter Exit Screw -- 11 Feet Long -- 16 Feet Wide -- 18 Feet High -- 12 Feet High Support LegsDismantled and Loaded on Truck

VERVILLE - 95-VP-438SE-CCW-35/125I: 4-Station Bagger complete Automatic Bag Placement and Bag SealerComplete Line was used for wood shavings only. The Line is in operation at the time of this write-up.The VERVILLE - VP438-CCW: 4-Station compression Bagging System designed for high-efficiency bagging operations.It features: High tubes of 125". Automatic plastic bag sealing Ability to handle bag sizes ranging from: 11" x 17" to 30" High.This System is often used in industries like: Biomass and Packaging. It also includes features: Oil tank heater and a Modem for remote monitoring.Bagging Capacity -- Handles bag sizes ranging from: 11" x 17" to 30" high. -- Automatic feature: Automatic plastic bag sealer for seamless operations. -- Height: System features: High tubes of 125 in., making it suitable for large-scale bagging needs. Additional Features -- Equipped with: Oil tank heater; modem for remote monitoring ensuring smooth and efficient performance.The control box is mounted on the side of the automatic Bagger with: ALLEN-BRADLEY Panel View 550 unit. -- Main 4-section Bagger: 125 " Tall. -- Main master control cabinet. -- Long 45° screw auger to feed from: Bottom of the Sifter to the top of the Bagger -- Master hydraulic tank & pump arrangement with all hoses. -- Full sealed bag auto. discharge conveyor belt & turning roller Conveyor. -- Sifter with: Canvas wrap cover. -- Screw Conveyor: Runs from under the outside dust Collection System rotary airlock: Drops the “good"; wood chips down to the 45° screw with “light dust" going out thru the Screw Conveyor into an open Dump Trunk outside.IMPORTANT ISSUESThe machinery requires a new Electronic Board & Computer with Software. Computer & Software is available, but it has to be programmed for this machine.Total HP: 75Price Includes: Loading on a Truck

VESTIL EHLT-2464-2-55 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 2,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 24" x 64". -- Lowered height 7", raised height 55". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VESTIL EHLT-4896-4-56 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 4,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 48" x 96". -- Lowered height 8", raised height 56". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VIET - S211 R+ KRT, 2-Head Wide Belt Sander43" Width. cap.: Drum and Combination head.Head Configuration:1st Head: 160 mm 6.3″ Helical grooved rubber drum. 25 HP motor2nd Head: 160 mm (6.3") Helical grooved rubber drum with a platen combination head., 25 HP motorSpecifications: -- Each heads are powered by a 25 HP motor. -- The heads can be programmed to pneumatically raise & lower along with the platen and do (3) sanding combinations (with the twist of a button). -- Digital height readout and a calibration unit to the left side of the conveyor. -- Conveyor speed is controlled via a variable frequency drive 2.5 HP . -- Max width: 43″. -- Max. height: 6-1/4". -- Variable speed conveyor belt drive from: 3 - 16 MPM (11 - 52 FPM).Equipped with & Features: -- Both heads are equipped with: 1,130 x 1900 mm (44-1/2" x 75"). -- Roller & pressure shoe holddowns. -- Pneumatic tension of sanding belts and feed conveyor. -- Load meter on main motor. -- Disc brake on main motor. -- Emergency stops front & back. -- Roller table extensions front & back.NOTE: This is an extremely low-hour 2012 BIESSE Viet S1 dual head 43″ calibrating Wide Belt Sander.

BIESSE - Viet Opera5 RRRF: Wide Belt Sander (4-Head) w/53" width cap.Head Configuration1st Head: Drum Unit The Roller Working Unit is: Characterized for the precision & effectiveness of the work it does.Main motor: 22 kW (30 HP).Drum: 240 mm; Steel Linear blower cleaning sanding paper A.S.S. (Air Saving System).Infeed pressure shoe.The pressure beam is used to guarantee the maximum precision when calibrating; flattens the deformed or thin pieces.Chromed anti-wear metal removable tips.Outfeed pressure shoe.2nd Head: Drum UnitMain motor: 18.5 kW (25 HP).Drum: 300 mm; 70 Shore.Linear blower cleaning sanding paper: A.S.S. (Air Saving System).Infeed pressure shoe.Outfeed pressure shoe.3rd Head: Drum UnitMain motor: 15 kW (20 HP).Drum: 300 mm - 40 shore.4th Head: Superfinishing UnitSuper-finishing pad: The evolution of the pad unit (VIET patent, 1978). The pad unit has a "chevron belt" running between the pad itself and the abrasive belt that guarantees top-quality finishing and a longer performance to the abrasive.Main motor inverter: 15 kW (20 HP).Pneumatic “air cushion"; pad: Pneumatic pad is the ideal tool to solve finishing problems.Contact insert for pneumatic pad made of: Steel + felt + graphite.Linear blower cleaning sanding paper: A.S.S. (Air Saving System).Infeed pressure shoe.Specifications -- Working width: 1,350 mm (53.15"). -- Constant Pass (Fixed Table): Heads adjust up/down by program. -- Working Height: 200 mm (7.87").Equipped with and Features -- Laser Electronic Positioning for working thickness. -- Motors with amp meters. -- IPC Compact 15" Color Touchscreen Controller. -- Vacuum Table with: 7.5 HP Motor. -- Electronic System: IPC Control with feed speed up to 75 FPM. -- 50 Shore Rubber Conveyor. -- Vacuum bed for: Short parts. -- Front & Rear Extension Rollers (2 each).

VIET (BIESSE) OPERA 5-3.3 XLL Denibbing Sander with 53" Width Capacity:53" Width cap. Denibbing Sander with a patented combination of rollers and rotating/oscillating discs make the VIET Opera Sanding Machine the ideal finishing solution for entry doors, cabinet doors, drawer fronts, sheet goods, shutters, face frames, furniture, and much more. Ideal solution for all sanding applications including whitewood, stain, and sealer coats. Head Configuration: -- 1st Unit: (11) Rotating discs with Slide out system for easy setup. 15 HP Electronic Inverter. -- 2nd & 3rd Units: 300 mm dia. Roller Brushes (Hub for 36 strips). Oscillating System with electronic 7.5 HP inverter. Specifications: -- Working Width: 1,350 mm (53.15"). -- Constant Pass Line TM (Fixed Table). -- Working Height Opening: 200 mm (7.87"). -- Laser Electronic Positioning for working thickness. -- Min. processing thickness 3 mm, Max. processing thickness 200 mm. -- (2) Longitudinal rotating brush-backed sanding rollers. -- 5" Rotating sanding discs. -- Forward speed 3-16 m/Min. -- Vacuum Table with 5.5 HP Motor, Electronic System, IPC Control. -- 50-Shore Rubber Conveyor. -- Front & Rear Extension Rollers. -- Emergency stop.Equipped with: -- IPC Touch-screen control: Simple & user-friendly "TOUCH SCREEN" IPC control with a color monitor. This control system supports the management of all machine parameters. -- PC processor provides control and feedback information to the machine in real time. -- The software version can be configured for right and left-handed operation. -- Text-free user interface; icons facilitate the operator's task. -- Optional rotating blower attachment at the back to blow off dust particles as items come off the machine. -- Includes matching transformer for 600 V to 460 V.

LACEY-HARMER LD-2002 Diode LaserEconomical self-contained Visable Diode Laser, optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° to +40° C operating temperature, 90 V for 250 nano-sec surge protection. Beam angle 5 to 90 degrees, 5mW to 35mW output, 636 nm wave length for lines up to 20' projection. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed. -- Optional items consist of: Crossbar style mounting bracket, please add...$ 90; axis slide brackets for easy positioning, add...$ 125 or alteratively a simple universal stationary mounting bracket, please add...$ 30.

LACEY-HARMER E-LINE Self-contained Visible Diode Laser End ShooterEconomical self-contained Visible Diode Laser; optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° - +40° C operating temperature, 90 V for 250 nano-Sec mechanical stock. Beam angle with 5 mW - 15 mW output, 636 nm wave length. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed -- Projects a line from approx. 12' to 15' depending on area lighting -- Consisting of two parts; (1) crossbar style mounting bracket, please add...$ 143; (2) axis slide brackets for easy positioning, add...$ 125 each or alteratively a simple universal stationary mounting bracket add...$ 30.

LAGUNA PRO 37 WIDE BELT SANDER1-Head, 36" width cap. - Combination sanding head with 4" dia. rubberized contact roll & 3" wide "dual action" polishing platen.Equipped with: -- Abrasive belt size 37" x 75" -- Pneumatic abrasive belt tensioning. -- Electronic abrasive belt tracking. -- 20 HP main drive motor. -- 1HP Variable feed speed motor for 12 - 60 FPM. -- 1/4 HP Conveyor bed elevation motor, with digital programmable thickness set up and AUTO-SIZE thickness system as well. -- Infeed & outfeed rubber covered holddown rolls. -- 0" - 5-1/2" thickness capacity.Complete with: -- Air-operated disc brakes on sanding head, emergency stop button

LAGUNA BM23E-2 ... Double Row Line Borer(2) 23-Spindle heads on 32 mm centers, (2) 3 HP motors, drills vertically from bottom.Specifications: -- Distance between first and last spindle 851 mm (33.50"). -- Spacing between zero and max. on the first head 0 - 4". Min. distance between two heads 7.25". Max. boring line spacing to the second head 24". -- 2,800 RPM spindle speed; collets accept 10 mm shank bits. -- Heavy overhead material holddown system with (4) pneumatic material clamps. -- (2) independent air throttles to control the drill-heads upstroke speed.Complete with: -- "Set screw" drill adapters, "quick set" system for depth of drilling. -- Extension fence with (3) flip-stops and foot pedal control.

LANGE MASCHINEN BAU B85K Edgebanding MachineSpecifications: -- Workpiece thickness: 8 – 50 mmWorkpiece width min.: approx. 75 mmWorkpiece length min.: approx. 120 mmEdging thickness: 0,4 – 3,0 mmMax edge thickness = Workpiece thickness + 4mm (2+2)One sided automatic edge banding machine with direct glue application to straight workpieces, high frequency cut off station, high frequency top and bottom milling unit, chain feed, double roller top pressure and work piece support. For ABS,PVC, melamine and strong wood veneer roll materials as well as fixed lengths.

LANGZAUNER G-5920 Cross-Cut Guillotine. Specifications: -- 35.5" Blade hydraulic pressure bar and knife; -- 5 Gal tank, pump is driven by 1.5 HP motor.Complete with: -- 2-Hand operation or foot pedal, Emergency-Stop, (3) photocells for safety, -- All safety guards per international standards.

LANTECH Q-300 Semi-Automatic Stretch Wrapper with Low-Profile RampSpecifications: -- Maximum versatility. Wraps large, tall, heavy or fragile loads including doors, windows and more. Production speeds 25 - 35 loads per hour. -- Maximum load size: Diagonal 73.5", Height 80", Weight 4,000 Lbs., Film roll diameter 10", Film web width 20".Equipped with: -- 65" Diameter Low-profile turntable with Variable speeds 0 -12 RPM & 3/4 HP TEFC. -- Power-roller stretch system - 200%. -- Micro-controller programmable control, Low-profile ramp.

Single head; 1.5 HP TEFC direct drive motor, spindle tilts 60° forward & 40° backward, inverter controlled variable speed from 400 - 1,800 RPM, RPM display; 4" vertical & horizontal spindle adjustment. -- Features: 36" x 33" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust hood w/piano hinge for easy ascess to sanding disc, stationary fence, large hand wheels for easy spindle adjustment.

Single head; 1.5 HP TEFC direct drive motor, spindle tilts 60° forward & 40° backward, inverter controlled variable speed from 400 - 1,800 RPM, RPM display; 4" vertical & horizontal spindle adjustment. -- Features: 36" x 33" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust hood w/piano hinge for easy ascess to sanding disc, stationary fence, large hand wheels for easy spindle adjustment.

Single head; 1 HP Belt drive motor, Fixed spindle, Mechanical controlled variable speed from 700 - 1,700 RPM, 4" vertical spindle adjustment. -- Features: 27" x 25" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust port, large hand wheels for easy spindle adjustment.

LARICK 120 Single Spindle Profile Sander;Sands raised panels, and door edges.Specifications: -- 1" Dia. x 4" long belt driven arbor; 700 - 1700 RPM variable speed, 1 HP motor. Arbor is vertically adjustable. -- Complete with: 25" x 22" butcherblock maple table, enclosed fabricated steel base and large hand wheels for easy spindle adjustment. -- Includes: Sensing safety guard for anti-automatic restart protection.

The Model 390 Automatic Shaper is a New concept in shapers. -- This "New Shaper" is conveyor fed, making it ideal for shaping small parts which could not be fed with a conventional Power Feeder. -- The 7.5 HP inverter controlled variable speed shaper can shape pre-arched panels automatically. Using a Template, it can also hog out arched panels. -- Horizontal and Vertical shaper adjustments with digital position indicators and the 5-position fence make profile changeovers extremely quick and simple. -- Standard stack tooling spindle -- Optional upgrade to 460 V, additional $ 250.