EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA - XR-12LE: Straight-Line Rip SawCompact Straight-Line Rip Saw with: Guaranteed 8' glue line. -- Powered by: 15 HP Direct drive motor. -- Equipped with: WYE-DELTA Soft Start for: Lower amp requirements during startup. -- Heat-treated chain & raceway with automatic oiler. -- All SQUARE D electrical controls. -- Large: 14-3/4" Rip capacity. -- Overarm control box: Mounted on the infeed side. -- Total space requirements: About the same as a standard size Table Saw.

"EXTREMA XF-34.3 Power Feeder w/Mounting Column;EXTREMELY" Heavy duty 3-Roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-38.1 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 3-roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (8) Speeds of 7 - 13 - 18 - 22 - 26 - 36 - 43 - 55 & 108 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-38.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 3-Roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (8) Speeds of 7 - 13 - 18 - 22 - 26 - 36 - 43 - 55 & 108 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floation of rollers for material thickness variations. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-3J Power Feeder w/Mounting Column;3-Roll Power Feeder with (3) rubber feed rollers. -- 0.25 HP Single phase motor. -- (4) Speeds of 20 - 26 - 33 & 43. -- Cast aluminum construction of the feeder housing. -- Heavy cast iron Universal Stand components. -- 1/2" Flotation of the rollers. -- Fully adjustable Mounting Column w/locking joints.

EXTREMA XF-44.1 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 4-roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Flotation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-44.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 4-Roll Power Feeder with 4-3/4" diameter x 2-1/4" wide rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Flotation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available).

EXTREMA XF-54T.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 5-roller CONTINUOUS BELT Power Feeder with (3) 44.5" x 1/2" tracks. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 15 - 28 - 39 & 78 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floatation travel of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

"EXTREMA XF-54T.1 Power Feeder w/Mounting Column;EXTREMELY" Heavy duty 5-roller continuous belt Power Feeder with (3) 44.5" x 1/2" tracks. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 15 - 28 - 39 & 78 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floatation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA XF-DC4.3 Power FeederExtrema has a wide range of power feeders that range from compact junior feeders to large 5-roller feeders. The XF-DC4 Series features a 4-roller system with variable speeds. Includes the 2/3HP DC brushless servo motor for higher torque and better variable speed control than a 1HP AC motor.Features: -- 4 Rollers -- FWD & REV -- 1PH or 3PH 230V -- DC Brushless Servo Motor -- 120mm x 60mm Rollers -- Infinitely variable feed speeds 7-72ft/minSpecification: -- Horsepower: .7HP -- Number of Rollers: 4 -- Number of Speeds: Variable -- Speeds: 7-72 -- Min Speed (ft/min): 7 -- Max Speed: 72 -- Suspension: 3/4" -- Roller Size: 120mm x 60mm Rollers -- Weight: 141 lbs

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

COMPLETE FANUC 125I ROBOTIC PALLETIZING SYSTEM System Includes the following: -- FANUC M-410IB/160 Palletizing Robot with Controller and Stand -- Robot will be tested -- End of Arm Tooling to Pick, Fork Style, Picking 94 Lbs Concrete Bags -- Master System Control Panel, 480 VAC 3PH & 24VDC Controls with HMI -- Allen-Bradley Light Curtain with Safety Controller --Infeed Chain Drive Roller Conveyor 10 Feet -- Pallet Hopper. ÷ Safety Fencing COST -- 20 Feet Exit CDLR Pallet Conveyor 52" Wide -- System Integration / Programming.

FANUC 165 Complete Palletizing SystemEquipped with and includes: -- FANUC 165 Complete with R-2000iA Controller with 600mm stand -- Pick-Up Arm Gripper Arm for pillow bag type -- 5 Feet x 24" Motorized In-feed Belt Conveyor -- (1) 10' Motorized Pallet Conveyor -- Automatic Pallet Dispenser -- Price includes Loading on your Truck

FANUC - S430iW, ...RobotFANUC Robot for palletizing rectangular compressed bags.Specifications -- (6) Axes. -- Payload: 165 kG (255 Lbs). -- H-Reach: 2,643 mm (104"). -- Robot mass: 1,300 kG (2,860 Lbs). -- Complete with: Pendant control. -- Complete with: Gripper type arm and pallet gripper. -- Refurbished with (90) days Warranty. -- Buyer to install safety guards.NOTE: Machine was rebuilt is 2021.

END ARM TOOLING FOR FANUC ROBOT -- Gripper Finger Type End Arm Tooling -- Design for Fanuc Robot Model S-430iW -- Loaded on your truck

FANUC 410 Palletizing systems with Infeed and OutfeedComplete Fanuc Case Palletizing System to include: -- Fanuc 410 Palletizing robot, Refurbished/Production ready -- Tooling for palletizing boxes (mechanical gripper) -- Rates of up to (35) boxes per minute sustained rate, robot will pick multiple boxes per cycle. -- Infeed conveyor (10' length) for orienting boxes for picks -- Pallet dispenser with pallet index chain --15' of motorized pallet conveyor -- Master Control panel for complete machine control from a single HMI touchscreen for user friendly operation -- Complete system programming, (6) pallet patterns. -- Complete AGS UL guarding package with safety controller and light curtains. -- 1-Year no charge tech support and remote access to machine.Professional factory installation - will be quoted separately.

FARR GOLD GS4 DUST/FUME/MATERIAL COLLECTOR: 3,000 CFM Rated cap., 1,300 sq. ft. filter area from (4) cartridge filters, approx. 2.3:1 air: cloth ratio . -- Equipped with: 5 HP Pull thru motor; dirty air is pulled into the filter area at bottom of filter media section allowing gross dust particles to fall into collector barrels located beneath pyramidal hopper discharging to a sealed drum (not included) -- Fine dust is pulled up thru the cartridge filters; dust filter cartridges are cleaned by automatic pulse jet with minimum compressed air consumption; cleaned air continues thru blower and is returned to the building air supply thru a silencer.. -- Includes: Cyclone with slide gate discharging into a sealed barrel (not included), electrical control panel, support stand with clearance under hopper, discharge for a waste bin,. access door, some pipe as pictured. -- Note this unit is still in use. Please inquire for availability date.