D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

DMC - UNISAND 2000-M2, ...Wide Belt Sander (2) Heads -- 53" Width cap. Drum, Platen.Head Configuration: --1st Head: 11" dia. (300 mm) Rubber-Covered Contac; (2) speeds or inverter adjustable 20 - 25 HP; Varied RPM. --2nd Head: Combination head with drum and graphite covered 2-1/2" finishing platen; 25 HP.Specifications: -- 54"x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computor controlled; set-up functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with: 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with: LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, motor load meters.2-Roll infeed conveyor extension; high efficiency dust extraction.

DMC - 1350 RK, ...TECHNOSAND Dual Head Wide Belt Sander.(2) Heads, 52" width cap. - Head sequence: Contact sanding roll and Segmented platen. Head Configuration:1st Head: 7" (175 mm) Dia., 85 durometer rubber-covered calibrating contact sanding roll.2nd Head: Segmented finishing platen with EPICS (sectional electronic pad) with (46) electronically controlled air segments.Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 1.5 HP feed drive, vacuum conveyor bed with 7.5 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Message from the Seller: The machine was setup by a DMC tech. It has a new calibration roller & new bearings, rebuilt HYDRA 35 controller; currently under power, comes with dust collecting manifold and hoses, plus the machine can be loaded onto a flatbed for ...$ 600.

DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350

DANCKAERT - 44 , ...ResawAir Strain 44"; x 5"; Bandsaw.Features & Specifications: -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to prevent spikes). -- Infeed & outfeed systems are the same. -- 24 ft. Long Camel Back chain (has air bags that are controlled by photo cell to raise & lower and index 1-board at a time). -- Max. length of lumber: 24 ft.From Seller: "The machine has a new VFDD 100 HP and a new WEG Severe Service 60 HP motor. All new hydraulic motors, caramel back chain, and roll cases."NOTE: Needs hydraulic unit.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: -- Specifications:Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. 3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: -- Specifications:Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. 3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Options Complete Over-all Foot Print 175’ long x 50’ wide

Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEKKER VMAX 40 HP Vacuum Pump (Liquid Ring):40 HP oil-sealed liquid ring compact motor-mounted vacuum pump system, 550 CFM, max. 29" Hg. -- Heavy duty construction:Compact design, small footprint, patented, high-efficiency DX-5 separator eliminates oil carry-over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant. Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation. Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct drive and withLow speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

DELTA 11-990C 12" 5-Speed Bench-Top Drill PressSpecifications: -- Table size 8-1/2" x 8-1/2" with 15-1/2"; x 40"; x 11/16"; Thick Plywood top, Table tilt 40° Left/Right. -- Base size 8-1/4" x 8-1/4". -- Quill travel 2-3/8", Chuck capacity 1/2", JT33 Spindle taper. -- Spindle speeds 620, 1,100, 1,720, 2,340, & 3,100 RPM.Equipped with: -- 1/3 HP - 1,720 RPM Motor.Complete with: -- Portable Wood Cabinet.Dimensions with cabinet: 41" x 36" x 57" H

Delta RC-63N 24" PLANER WITH SPIRAL CUTTER HEADSpecifications -- 24" x 9" Cap., 5/16" max. material removal, -- 10-1/2" min. part length. -- 15 HP Belt drive motor, -- Spiral Cutting Head -- 5,000 RPM, variable feed speed from 20 - 60 FPM.Equipped with & Features -- Powered raise and lower of 25" x 35" table, -- Sectional chipbreakers, sectional infeed roller & dual outfeed rollers. -- Push button magnetic control, -- Dust hood, & grinding attachment to sharpen helical head knives while on the machine.

DELTA RC-51 PLANER20" x 9" Cap., 7.5 HP motor, 4-knife cutterhead, power raise-and-lower adjustment and fine adjustment thru a convenient hand wheel; variable feed speed 16 - 28 FPM; equipped with sectional chipbreakers, adjustable bed & dual outfeed rollers. Actual model 22460

DELTA - UNISAW, ...Table SawSpecifications: -- 10" Blade dia., 3 HP - 3,450 RPM motor belt drives 5/8" dia. arbor @ 4,000 RPM, arbor tilts 0° - 45°. -- 3-1/8" Max. depth @ 90°; 2-1/8" max. depth @ 45°; 25" max. rip cap. to right of blade and 15-1/2" max. to left of blade, 13/16" max. dado width. -- Includes: -- 27" x 40" Cast iron table, distance front edge of saw to blade 12-1/4", 34" table height; DELTA Rip Fence; (1) set of dado blades.

DELTA - 22-650, ...Single Planer.DELTA/INVICTA 12" Table Top (no stand) Single Planer equipped with: 2 HP motor; 3-knife round cutterhead; with rollers.Capacity of 12"; feed rate of 15-1/2 FPM.250 LBS

DELTA RS-15 SINGLE SPINDLE SHAPERSpecifications: -- 1-1/4" interchangeable spindle. -- 7.5 HP motor with (5) spindle speeds of 2,800 - 4,500 - 6,000 - 8,000 & 10,000 RPM. -- Vertical spindle travel is 7-3/4", with 5-5/16" capacity under the nut. -- 35-1/2" x 43" fixed table with 13" max. table insert diameter.Complete with: -- Spindle reversing switch, spindle foot brake & lock, and adjustable fence. -- HOLZ Power Feeder is included

DENRAY 2800 Down Draft TableConvenient size 28" x 48" table. -- 2,800 CFM Rating at 1" static with 1-1/2 HP motor. -- Space-saving self-contained unit with no ductwork and no loss of conditioned air. Tube filter system cleans with 99% capture rate at 1 micron. -- Comfortable 36" working height. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick steel-reinforced MDF board and rubberized surface. -- (4) 4" Swivel casters with (2) that lock. -- Options available; Exhaust Muffler to reduce sound level 10 - 12 dBA, Magnehelic Gauges, HEPA Filter Banks, 3-Sided 20" Shields and Odor Control Filters. -- Also available in 230V, 460V and 575V, 3-Ph

DENRAY 2872 Down Draft TableLarge work surface on this 28" x 72" table (overall). -- Rated at 3,400 CFM, with 2 HP motor and magnetic starter. -- Space-saving self-contained unit w/built-in dust drawer. -- Features; New Tube Filtration System which cleans with a 99% capture rate at 1 micron. -- Quiet operation at only 77 dBA sound level. -- Comfortable 34-1/2" working height. -- 3/4" Thick steel-reinforced MDF board worktable with "non-marring" rubberized surface. -- Easy manual filter cleaning. -- (4) Casters, (2) of which lock in place. -- 115 Volt receptacle with 8' cord. -- Available options; Exhaust Mufflers to reduce sound 10 - 12 dBA, Magnehelic Gauges, HEPA Filter Banks, 3-Sided 20" shields and Odor Control Filters. -- Also available in 230V, 460V and 575V, 3-PH which includes magnetic starter.

DENRAY 2896 Down Draft Sanding Table: Extra long 28" x 96" table with a 36" working height. -- Rated at 3,500 CFM with 2 HP single phase motor. -- This model features the New Tube Filtration System which cleans with a 99% capture rate at 1 micron. -- Includes: (4) Swivel casters, including (2) that lock in place. -- No duct work, no loss of conditioned air. -- Comfortable 1-1/8" thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Available options include; Exhaust Muffler to reduce sound 10 - 12 dBA, Magnehelic Gauges, HEPA Filter Banks, 3-Sided 20" Shields and Odor Control Filters. -- Also available in 230V, 460V and 575V, 3-PH.These tables are popular with small to medium shops to incorporate (2) operators side by side or for use on longer products.

DENRAY 9600 B Down Draft Sanding TableExtra large 48" x 96" table; Comfortable 36" working height. -- Powerful system with 4,800 CFM rating. -- 5 HP Motor with magnetic starter. -- Space-saving self-contained unit w/built-in dust drawers and high efficiency cartridge filters. -- No duct work, no loss of conditioned air. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Fully enclosed unit. -- "Self-Cleaning" System with push button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust that can be directed away from operator. -- Quiet operation with only 82 dB. -- Available options; (4) Swivel casters with (2) that lock in place, Auto-Self cleaning timer or muffler.

DENRAY 7200 B DOWN DRAFT TABLELarge 48" x 72" Table. -- 3,900 CFM rating after filters. -- 5 HP Motor w/magnetic starter. -- Space-saving fully self-contained unit: No duct work, no loss of conditioned air. Contains (2) cartridge filters that clean to 0.5 microns. -- Comfortable working height 36". -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- "Self-Cleaning" System with push button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust which can be directed away from the operator. -- 84 dBA Sound level. -- Options include; Timer to automatically clean filters without operator, (4) swivel casters (2) that lock into place, noise reducing muffler (Reduces volume by 10 to 12 dBA),Unit also available in 220 V single-phase.

DENRAY 3660B Down Draft Sanding TableConvenient 36" x 60" table with a 36" working height with DENRAY's Pulse jet Cleaning System. -- Rated at 3,400 CFM for fast, easy removal of dust. -- 2 HP 3-phase motor. -- Space-saving self-contained, double filtration unit with integrated table top surface filter and bottom filters on all (4) sides. -- No duct work, no loss of conditioned air. Sound level 74 dBA. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board with rubberized surface. -- Also available in 115 V and 220 V single phase