This BRIGHTLINE 532 mm Alignment Laser will work well on a variety of machines, and on dark surrfaces shows up better than the common Red line. -- The 5 mW Green line shows four to five times more visable to the human eye than an equally Powered Red line. -- The output power is 5 mW; 100º fan angle. -- Expected life 3,000 - 5,000 hours. -- Projection type (dot/line/cross): Dot. -- Package includes: Alignment Laser mounted in a block, Mounting bracket and power supply. This light can also be powerd by direct 3.0 VDC (300 - 800 mA draw). -- Laser beam thickness at aperture is 3 mm with a divergence of 0.1 mm for every meter of beam length. This is a focus adjustable laser with an operating temperature of 15C - 35C.

This BRIGHTLINE 635 Mm Alignment Laser will work well on a variety of machines. It is ideal for any aplication where a highly visible line projected onto a surface is needed. -- The output power is 5 mW; 100º fan angle. -- Expected life 3,000 - 5,000 hours. -- Projection type is a line and is focus adjustable. -- Package includes: Alignment Laser mounted in a block with mounting bracket and a direct 3.0 VDC (300 - 800 mA draw) power supply. -- Line straightness better than 0.1% over full length, line divergence (beam diameter) will expand 0.3 mm for every 1 meter increase in distance from the Laser to the target surface. The beam diameter at the aperture is 4.0 mm. -- Operating temperature is -10°C to +40°C.

LEADERMAC SYC 300M Heavy Duty Roll Feed Ripsaw: Features & General Description: -- Cast Iron base with easily accessed Anchor Bolts; lift up sound enclosure with light for quieter and safer operation; Hydro-Loc Outboard Bearing System for best gang sawing shaft support, includes grease gun; HD Cardan shaft feed (chainless) drive throughout. -- (6) Full width, close coupled driven top feed rollers; (4) full width driven bed rollers; top rolls are air tensioned; variable pressure controls on top feed rolls; motorized lift to top rolls; infeed table is hard chromed with approx. 0.012"; - 0.014"; chrome. -- Easily adjusted roll holdover on the infeed table; saw spindle has motorized lift and lowering; multiple HD V-belt driven saw spindle with special HD belt tensioner; saw blades cut from below, hence better dust removal and a heavier sturdier design. -- Saws are pre-mounted on a slip-on sleeve for quick change; (3) sets of anti-kickback devices included; central lube system; pneumatic pressure controller safety switch – if air pressure to the top rolls drops below the set to run level, the feed will automatically stop. -- Controls include: VFD Control to feed speeds and Digital Speed Readout in FPM or MPM; TECO-WESTINGHOUSE main electric motor; I.E.C. – TELEMECANIQUE-SQUARE-D Electricals meet or exceed UL/CSA Standards. -- Machine is equipped with WYE-DELTA Soft-Start (low Amperage) starters & main disconnect, multiple “E-Stops" operate at low amperageSPECIFICATIONS: -- Max. thickness, 5.1"; (130 mm); Note – to 4-1/2"; with std. 14"; diameter blades; to 5.1"; with optional 16"; Blades. -- Saw sleeve usable length of 12.3"; (312 mm) - max. dist. between outside saws; minimum length material, 10"; (250 mm) – at slower speeds. -- Saw Blades with 10"; min. to 14"; max dia. x 70 mm Bore (double key), 16"; (400 mm) optional – no charge; Saw spindle with 50 mm dia. runs at 3,200 RPM; Saw sleeve – included, 70 mm OD with double keyways. - Includes (1) set of spacers. -- Main Motor – 75 HP (50, 60, or 100 HP optional); top feed rolls – rise & fall, 1 HP; Feed Drive of 7.5 HP with VFD infinitely variable speed control, 20 to 165 FPM (6 to 50 MPM) to 200 FPM – 60 MPM – optional). -- (4) 150 mm Dust collection outlets; approx. weight – net, 5,060 Lbs.; WYE-DELTA – low Amperage - Soft Start for main motor starter; electrics to UL/CSA Standards and wired to 230/460 or 575/3/60. - Note: Stock machines are with 50 HP – 460/3/60 electrics machine and can be easily and inexpensively transformed to other voltages.Optional Extras. -- 75 KVA Auto Transformer to run machine on 230/3/60 electrics, please add ...$ 2,045. -- 16"; (400 mm) Dia. blade with 5.1"; max. Thickness N/C; NOTE: – Contact us to see if stock machine has this capacity. -- Extra Saw Sleeve, add ...$ 995. -- Additional Sets of spacers for saw sleeve, P.O.R. -- 20 MW Laser & Laser Holder w/12"; Bolt o

LEADERMAC LMC-101-900 HD 36" HD Multi-Blade "Roll Feed" RIP SAWSpecifications: -- Working width: 0.6"; – 36"; -- Working thickness: 0.4"; – 4"; -- Up & Down motor: 1 HP -- Feed motor: 7-1/2 HP with VFD -- Spindle HP: 75 HP, larger motors optional -- Spindle diameter: 3.15"; double keyed -- Spindle RPM: Std. 4,000 RPM, 5,000 RPM optional -- Saw Blade Diameter, 14"; diameter -- Feed speed, infinitely variable: 20 – 50 FPM, 100 or 200 FPM optionalStandard Features: -- Extra Heavy Main Frame – Stress Relieved -- Sound & Safety enclosure included – with internal strobe-free lighting -- High Precision Spindle - Double Keyed assembly with Hydro-Lock outboard bearing assembly on outboard side -- Spindle assembly slides out on support for Quick, Easy and Precision Saw Setting & Changing -- Hardened & Hard Chromed Feed Tables -- (7) Sets of Top Power Driven Rolls – full width -- (5) Bottom Power Driven Rolls – full width -- Infinitely Variable Pneumatic Pressure to Top Feed Rolls -- Top & Bottom Feed Rolls driven by Cardan Shaft Drive with HD Gearboxes Interconnected -- 1st Top & 1st Bottom Powered Roll Combination and then (2) Rows Anti Kick Back Finger Units Full Width and then to the rest of the Powered Top & Bottom Rolls provide the best Feeding Capability with excellent safety features -- HD VFD – 7-1/2 HP Feed System – Infinitely Variable -- Main motor has Wye-Delta low amperage soft start -- Electrics are 230, 450 or 575 volts 3/60 with all controls to CSA/UL Specifications -- Documentation: Maintenance manual, Operation manual, Electrical diagrams, Parts list & Tool Box (Electronic Version on Request) -- (8) Dust outlets consisting of (4) top & (4) bottom 6"; diameter dust hoods -- Saws, Dado Heads &/or cutterhead(s) and spacers optional extra Options Included In Price: -- Hanging Control Panel – in lieu of Control std. setup as shown in machine photo, Included -- Moveable Main Electrical Panel with 10 ft. of main cable, Included -- Amp Meter for the Arbor Motor, Included -- 4"; Thickness capacity in lieu of standard 2"; thickness, Included Available Options: -- To 3" Thickness Capacity – using 12"; blades, P.O.R. -- To 3"; or 4"; thickness Capacity – using 14"; blades, P.O.R. -- To 100 FPM Top Feed Speed – Infinitely Variable – 4"; Thickness Capacity, POR -- To 200 FPM Top Feed Speed – Infinitely Variable – 2"; max. Thickness, P.O.R. -- 100 HP saw spindle motor, P.O.R. -- 125 HP saw spindle motor, P.O.R. -- 150 HP saw spindle motor, P.O.R. -- Front or Rear 10 HP Side Heads (Please discuss if interested), P.O.R. -- 15 HP or 20 HP Side Head motors in lieu of 10 HP, P.O.R. -- Adjustment of the Rear guide with digital readout from the front of the machine (only desirable if Side Heads are supplied), P.O.R. -- Scoring Saw Arbor ahead of main saws if desired, P.O.R. -- Saw Spacers for Main Arbor quick Setup, P.O.R. -- Mechanical Quick Lock Saw collars if de

MORBIDELLI - M 400 F: Flat Table Machine (Loading/Unloading) -- Specifications5' x 12' Stationary extruded aluminum "MATRIX" table for "Nested Base" manufacturing with: "Rake" & "Automatic Offloading Conveyor".Loading/working/processing direction from: LH (Facing to RH (facing). -- Work Area"X" Axis 143.7" (3,650 mm); "Y" axis 62.9" (1,600 mm); "Z" axis stroke 11" (280 mm); max material thickness: 6.69" (170 mm). -- Positioning Speeds"X" & "Y" Axes: 279 FPM (85 MPM); "Z" axis: 98 FPM (30 MPM).Closed loop AC Servo drive system with: Precision rack & pinion in "X" axis; recirculating ground ball screw in the "Y" & "Z" axes.All axes ride on precision prism linear guideways. -- Worktable5' x 12' Aluminum grid "MATRIX" vacuum table machined with: Square grid pattern for fixturing parts; grid pattern allows use of vacuum pods or closed cell rope gasket material & use of spoil boards.(9) Independent NC controlled working zone areas; external pop-up reference pins located on the sides & back of the table for positioning parts. -- Boring Unit3 HP (2.2 kW) - Variable speed: Up to 8,000 RPM motor; "F37L2" boring block with (24) Vertical spindles with: (10) independent vertical spindles in "X" axis & (14) spindles in "Y" axis.10-Spindle "X" axis boring unit NC controlled with: 11-1/2" (293 mm) "Y" Adjustable spread from its home position; independently controlled according to the drilling pattern being performed; this feature is IDEAL for high-speed line hole drilling.(12) Horizontal spindles with (4 + 4) in "X" axis on the programmable independently NC controlled 10-spindle vertical boring unit; (2 + 2) on the 14-spindle boring unit in "Y" axis. (1) NC Controlled 0° - 90° "X" / "Y" Grooving Saw for max. 120 mm dia. blade. -- Machining(1) 16-1/2 HP (12 kW) "Power 2000" Electrospindle with: Lifetime lubrication; HSK F63 adaptor; NC controlled spindle speeds from: 900 - 18,000 RPM.(1) 16-position "Rapid-16 traveling ATC tool plate for "on the fly" ATC. NC Touch-off Probe for: automatic tool length setting. -- Operator InterfacePC Front-End with: "eye-M" + Windows Operating System mounted in separate control cabinet; INTEL 1.0 GHz Pentium III microprocessor; 20 GB hard drive; 56 K modem; integrated 3Com network card; 128 MB.15" VGA Color monitor & ergonomic keypad; serial ports RS-232 & RS-242; USB ports. "eye-M" Offers incredible list of functions from: (a) Auto diagnostic to (z) zooming; controlled acceleration & deceleration; encoder feedback; dynamic tool correction via PLC due to active tool wear using space-and-time criteria; programs can be transferred via diskette or downloaded by wire.Additionally equipped with: an on-board mini CAD with built-in programming for: Writing circles; ellipses; angles with only a few keystrokes; on board cycle optimization; onboard calculator; mirror imaging; repeat imaging. -- Complete with:(2) 360 m³/Hr "BECKER" Vacuum pumps; automatic central lubrication; central optimized Dust Collection; multi-voltage autotrans

MORBIDELLI - N 100 15: Flat Table Machine with ATC, Boring -- Specifications:• 5' x 12' Worktable• 13 HP (S6) air cooled electro spindle with HSK F 63 quick release tool holder• 1,500 to 24,000 RPM inverter-controlled spindle speed• Aluminum solid worktable that can nest full sheets or be used for routing smaller components• 14-Position tool changer mounted to side of machine• (12) Vertical drills: (7) in X axis and (5) in Y axis• X/Y maximum positioning speeds is 35 meters/min (115 feet/min)• Z axis stroke 250 mm (9.84")• Maximum panel passage 150 mm (5.90")• (2) 300 m³/H vacuum pumps• Mobile console with 17" LCD display with Windows 7 operating system• XILOG PLUS Operator Interface and Xilog Maestro Cad Cam free form software with labeling. 7" color universal remote-control pendant allows for the effective management of all machine functions from movement of controlled axes in manual jog mode to loading and execution of a program. Fitted with a USB port which allows for a quick load and setup of new programs. Air-Conditioned electrical cabinet.• Safety bumpers on both sides of the mobile unit allows for safe movement while saving space by eliminating caging around the machine. • Electronic tool detecting length (touch probe) allows for detecting tool length without running a test program• Dust Collection: (1) 200 mm (7.87") on router (1570 cfm)• Operating air pressure with 3/4" ID hose 7 ATM (102 psi)• Autotransformer allows choice of 208/230 or 460 volt 3 phase operation

MORBIDELLI - AUTHOR 330: Flat Table Machine (w/ATC/Boring) -- Specifications4' x 10' Stationary extruded aluminum "MATRIX" table for "Nested Base" manufacturing. -- Work Area"X" Axis: 113.85" (2,892 mm); "Y" axis: 50.78" (1,290 mm); "Z" axis stroke: 11" (280 mm); max material thickness: 4.7" (120 mm). -- NOTE: When using the "Rake System," 4' x 8' is the max. panel size. -- Positioning Speed"X" Axis: 262 FPM (80 MPM); "Y" axis: 148 FPM (45 MPM); "Z" axis: 74 FPM (22.5 MPM). -- Closed loop AC Servo drive system with: Recirculating ground ball screw in the "X", "Y" & "Z" axes; all axes ride on precision prism linear guideways. -- WorktableAluminum grid "MATRIX" vacuum table machined with: Square grid pattern for fixturing parts; grid pattern allows use of vacuum pods or closed cell rope gasket material and use of spoil boards. -- (2) Independent working areas; external pop-up reference pins located on the sides & back of the table for positioning parts. -- Boring Unit2 HP (1.5 kW) - 4,000 RPM Motor; (12) independent vertical boring spindles: (7) Spindles in "X" axis & (5) spindles in "Y" axis. -- Machining (1) 10 HP (7.5 kW) "Power 2000" Electrospindle w/lifetime lubrication; HSK F63 adaptor; spindle speeds from: 900 - 18,000 RPM. -- (1) 12-Position "Rapid-12" traveling ATC tool plate for "on the fly" ATC. -- Operator InterfacePC Front-End with: NUM 1040 + Xilog III + Windows Operating System. -- 12" High resolution CRT, ergonomic keypad; 1.44 MB & CD ROM disk drives; (2) serial ports: RS-232 & RS-242. -- All housed in air-conditioned cabinet with: KELVIN Air-Conditioner. -- Complete with:(2) 300 cbm/Hr Vacuum pumps; emergency stop rope; Safety "Bump-Stop" system; Handheld pendant control. -- Options IncludedNesting Rake & off feed table to increase machine/Operator output. -- "SOUTHWORTH" Lift Table; roller conveyor section to bridge safety barrier. -- (1) 10 HP (7.5 kW); 460 V; 3 Cy DUSTEK 3-bag Dust Collector. -- Actual model: MORBIDELLI AUTHOR 330 NBR

MORBIDELLI - N 100 15. Flat Table Machine with: ATC, Boring -- Specifications5' x 12' x 37"; H - High efficiency laminate aluminum with: Vacuum locking system.Grid pattern allows: Use of vacuum pods or closed cell rope gasket material; use of spoilboards for nested-base machining. Part location pop-up pins mounted on: Table perimeter; chips conveying device. -- Working AreaX-Axis: 3,686 mm (145.12"); Y-Axis: 1,555 mm (61.22"); Z- Axis stroke: 250 mm (9.8"); Z- Axis: 150 mm (5.9"). -- TravelsX-Axis: 4,230 mm (166.54"); Y-Axis: 1,985 mm (78.15"); Z-Axis: 250 mm (9.84"). -- Positioning SpeedsX- & Y- Axes: 35 MPM (114 FPM); moving gantry, high precision rack & pinion system for: X & Y Axes; ground ball screws for: Z-Axis. All axes ride on extra large precision profile linear guide ways. -- Boring Unit2.2 kW (3 HP) Motor; (12) independent vertical roto-axial spindles with: (8) In X-Axis; (4) in Y-Axis; max. spindle speed: 8,000 RPM. -- Machining(1) 9.6 kW (13 HP) Air-cooled electrospindle with: HSK F63 Adaptor; variable spindle speeds: 1,500 - 24,000 RPM; (1) 14-position TR side tool changer. -- Operator InterfaceMobile console: 17" LCD Display with Windows 7 Operating System.“XILOG PLUS Operator Interface & Xilog MAESRO CAD CAM free-form software with labeling. "MAESTRO SUITE" with: Auto-diagnostic to zooming; controlled acceleration & deceleration; encoder feedback; dynamic tool correction via PLC: Due to active tool wear using space-and-time criteria; "TECPAD" remote pendant with: 7" Color touchscreen & fitted with a USB port, which allows for a quick load & setup of new programs. -- Complete with: (1) 300 CBM/Hr Vacuum Pumps; air-conditioned electrical cabinet. - Universal 3-phase transformer.Electronic tool detecting length (touch probe) allows for: Detecting tool length without running a test program.Safety bumpers on both sides of the mobile unit allow: Safe movement while saving space by eliminating caging around the machine.

MORBIDELLI UNIFLEX HP 1.1 CNC MACHINING CENTER (2-HEAD): -- Specifications:Flexible "TOP & BOTTOM" Machining Center that uses an innovative panel handling system. -- Positioning SpeedsThe "UNIFLEX" can reach positioning speeds of: 130 MPM in "X" Axis; 80 MPM in "Y" axis; 50 MPM in "Z" axis with total safety, providing an unmatched working capacity. -- Working DimensionsMax. worktable part size for: "X" axis is 118" (3,000 mm); "Y" axis is 51" (1,300 mm) "Z" axis max. part thickness 3.1" (80 mm).Min. worktable part size for: "X" Axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness 0.157" (4 mm). -- Worktable:Automatic LH infeed air table with gripper clamps; automatic RH outfeed transfer conveyor with belts; both infeed & outfeed are considered Robot ready. -- Boring Units:(1) Top mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2+2) in "X" axis & (1+1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade.(1) Bottom mounted boring block: 4.2 HP (3 kW); variable speed from 1,500 - 6,000 RPM; (48) vertical spindles: 24-Spindles in "X axis & 24-spindles in "Y" axis; (6) horizontal spindles with: (2 + 2) in "X" axis & (1 + 1) in "Y" axis; (1) 4.2 HP (3 kW) - 9,000 RPM, NC controlled 0°-90° "X/Y" Grooving Saw, max. 120 mm dia. blade. -- Machining:(1) Top mounted 10 HP (7.5 kW) electro-spindle with: HSK D-50 Adaptor; "ERC 32" tool holders & RC-32 collets, 1,500 - 24,000 RPM.(1) Bottom mounted 10 HP (7.5 kW) electro-spindle HSK D-50 adaptors, "ERC 32" tool holders & RC-32 collets; 1,500 - 24,000 RPM. -- Operator Interface:PC Front-End with: "XYLOG PLUS" + Windows environment Operating system; 20 GB hard drive; 17" TFT monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy drive; (1) CD ROM drive; all mounted in separate control console. -- Operating System:"XYLOG PLUS" Offers Real time multitask processing; programs can be transferred via diskette or downloaded by wire. -- Complete with: Pneumatic part clamping devices; sound enclosure; safety mats. -- Operating features: Machine can work the panel from above & below at the same time and can produce (2) identical or mirrored panels per cycle with no difficulty.The "UNIFLEX" can machine porous materials since the pieces are held with grippers, directly managed by the numerical control; it can even process small pieces and carry out "through" machining.(4) Operating modes at each cycle, it can change automatically from: Top machining to bottom machining, to top & bottom machining together, either on (1 or 2) stacked panels. -- Actual model is MORBIDELLI UNIFLEX HP.

MORBIDELLI - CX 100: CNC Machining Center (Vertical) -- SpecificationsFlexible "Vertical" Machining Center reaches movement speeds of: 229 FPM (70 MPM) in "X" axis; 131 FPM (40 MPM) in "Y" axis; 98 FPM (30 MPM) in "Z" axis with: Total safety. -- Working CapacityMax. part size for: "X" Axis is 120" (3,050 mm); "Y" axis 35.4" (900 mm); max. part thickness: 2.3" (60 mm). - Min part size for: "X" Axis is 7.8" (200 mm); "Y" axis 1.96" (50 mm); min. part thickness of 0.31" (8 mm); automatic infeed & outfeed from the LH side. -- Boring UnitBoring block with: 3 HP (2.2 kW) Motors; variable speed: Up to 8,000 RPM with: (12) Independent spindles: (7) In "X" axis; (5) in "Y" axis. - (6) Horizontal spindles with: (2 + 2) in "X" axis; (1 + 1) in "Y" axis. - (1) "X" Axis: Grooving saw; variable speed up to: 10,000 RPM; 125 mm max saw blade diameter. -- Machining(1) 7.4 HP (5.5 kW) Router with: ISO 30 Adaptor. - Variable speed from: 1,000 - 24,000 RPM. -- Operator InterfacePC Frontend. SCM "XILOG MAESTRO" + Windows Operating System with 3D graphics. Includes: 17" TFT Monitor; international keyboard; soft touch keypad & industrial mouse; RS-232 Serial ports; USB ports. Ethernet Connection. Real time multitask processing; programs can be transferred via: Diskette or downloading by wire is possible. -- Complete with:Handheld pendent control; (2) pneumatic part clamping devices; auto. lubrication system; sound enclosure & safety devices. -- Actual Model is: SCM MORBIDELLI CX 100

MORBIDELLI - CX 220: CNC Machining Center (Vertical) with (2) NC Controlled "Split Heads" -- Specifications• HSK63F Electrospindle.• 6-Position tool holders.• (S1/S6) 6.6/7.5 kW (9/10.2 HP).• Constant motor power from: 12,000 - 18,000 RPM.• Automatic lubrication.• Autotransformer.• Drilling on (5) faces.• "EYE-M" PC Controller.• 21-1/2" LCD Color display.Drill Head #1• Vertical spindles: 21.• Horizontal spindles in X direction: 6.• Horizontal spindles in Y direction: 4.• Integrated blade in X axis: Ø 125 mm.• Max. saw blade thickness: 6 mm.• Motor power: 2.2 kW (3 HP).Drill Head #2• Vertical spindles: 13.• Horizontal spindles in X direction: 6.• Horizontal spindles in Y direction: 2.• Integrated blade in X axis: Ø 125 mm.• Max. saw blade thickness: 6 mm.• Motor power 2.2 kW ((3 HP).• Actual Model: MORBIDELLI CX 220.

MORBIDELLI - X200: Flat Table Machine with ATC / BORING / RAKE / OFFLOADING -- Specifications5' x 10' Traveling "Bridge Gantry"; stationary aluminum "MATRIX" grid table with: Square grid pattern for fixturing parts.Grid pattern allows: Use of vacuum pods or closed cell rope gasketing material; use of spoil boards for "nested base machining".(8) Vacuum zones controlled by electronic switches; (5) part location pop-up pins mounted on the table perimeter.Working Flow from left-to-right direction. -- Working Field"X" Axis: 123" (3,117 mm); "Y" axis: 61" (1,557 mm); "Z" axis stroke: 9.4" (240 mm); max. material thickness: 5.9" (150 mm). -- Work TableWorktable divided into (8) Vacuum Zones with: Automatic & manual selection. -- Positioning SpeedPRO-SPEED "X" & "Y" Axis vectorial speed; 370 FPM (113 MPM); "Z" axis positioning: 82 FPM (26 MPM); closed loop AC Servo drive system.High precision "Rack & Pinion" system in: "X" & "Y" axis; ground ball screws "Z" axis; all axes ride on extra-large precision profile linear guideways. -- Boring Unit"F16V Ro.Ax" Boring Unit: 3 HP (2.2 kW); variable speed: 1,000 - 8,000 Max. RPM motor.(16) Independent vertical spindles on 32 mm Centers; (8) spindles in: "X" axis; (8) spindles in: "Y" axis. (12) Horizontal Spindles with: (4 + 4) in "X" axis; (2 + 2) in "Y" axis. (1) "X" Axis Grooving Saw with: Max. 120 mm dia. blade. -- Machining(1) 20 HP (14 KW) Air-cooled electro spindle with: HSK F63 Adaptor; variable spindle speeds: 1,500 - 24,000 RPM.(1) 14-Position "FAST 14" ATC tool rack mounted inside the protective cage on the mobile unit. -- Operator InterfacePC Front-End with: "Eye-M"; + "Maestro-Active HMI" (Human-Machine Interface Software) + Windows "10" Operating System.21-1/2" Full HD touchscreen; USB ports; serial ports: RS-232 & RS-242; Ethernet adaptor.Programs can be transferred via USB or downloading by wire is possible; all computer components are mounted on a mobile stand. "Xilog Maestro Active HMI" (Human Machine Interface software)"; offers incredible list of functions from: (a) Auto-diagnostic to (z) zooming; controlled acceleration & deceleration; encoder feedback; dynamic tool correction via PLC due to active tool wear using space-and-time criteria.MSL Connector (Maestro Scripting Language): Software module developed by SCM Group to directly connect its own CNC machines with: Main 3rd Party software packages available on the market.Maestro is: Protected against unauthorized copy through a hardware USB key.Includes 1-License for: "Xilog Maestro CAD CAM" Free Form Software + Maestro-Connect: (1) Year subscription service.Maestro-Connect: Complete hardware preset for IoT Platform. Additionally equipped with onboard mini-CAD with: Built-in programming for writing circles, ellipses, & angles with only a few keystrokes.Onboard cycle optimization, onboard calculator, mirror imaging, and repeat imaging. -- Complete with:(2) 300 m³/Hr Vacuum Pumps; Handheld "TECPAD" remote control with: 7" Touchscreen, co

MSI - AT-643: Horizontal Auto-Tie Baler with Infeed ConveyorSpecifications: -- 60" x 43" Feed opening. -- Bale size: Variable x 43" x 30". -- Bale weight: 900 - 1,700 Pounds; OCC" 5 TPH. -- Cylinder: 7"; repacked. -- Motor: 40 HP. -- New hydraulic pumps; new "T-1" Liners on floor & platen. -- 60" Wide x 25 feet long slider bed; conveyor included.

MTB BDV-1200 SHREDDER --Specifications Per Manufacture's Information --ROTOR Length: 1200 mm (47.2 INCH) Diameter: 416 mm (16.4 INCH) -- 150hp 460 volts -- The unique features of our BDR shredders allow for the most efficient size reduction of difficult material types at the lowest operating costs on the market -- Includes Stand and Hopper

MULTICAM APEX 3R with 5' X 10' Table and ATC:60" x 120" Fixed table, moving gantry machine in a front-to-back configuration with a multi-zone vacuum table supported by a 20 HP vacuum blower system. -- Equipped with:(1) 10 HP "HSD" spindle with 8-position static tool changer, variable speed by inverter up to 24,000 RPM. -- Full table coverage:X- & Y-axis, rack & pinion gantry drive with brushless Servo motors using integrated 25 mm linear roller bearing rack system, 8" Z-axis travel via lead screw drive. 1,000 IPM Max. cutting feed, 1,700 IPM max. rapid traverse rate on X- & Y-axis. -- Control:The MULTICAM CNC controller Is a stand-alone RISC/DSP system. The controller includes a keypad interface with hot keys for repetitious functions and DNC access to host computer. Memory for instant job replay, 32-bit processor, 12 MB RAM & 2 MB flash memory, interprets HPGL and M & G codes, RS-232 interface for PC communication. -- Includes:(20 HP) Vacuum blower for hold-down, assorted collets and tool-holder will be included.

MULTICAM APEX 3R with 4' X 8' Table and ATC:48" x 96" Fixed table, moving gantry machine in a front-to-back configuration with a 4-zone vacuum table supported by a 20 HP Republic vacuum blower system. -- Equipped with:(1) 13.4 HP "HSD" spindle with HSK F63 adaptor. (1) 6-position static tool changer, variable speed by inverter up to 24,000 RPM. -- 4 Zone Pneumatic Table:X- & Y-axis, rack & pinion gantry drive with brushless Servo motors using integrated 25 mm linear roller bearing rack system, 6" Z-axis clearance via lead screw drive. 1,000 IPM Max. cutting feed, 1,700 IPM max. rapid traverse rate on X- & Y-axis. -- Control:The MULTICAM Pendant Programmable Controller, PC, is a stand-alone RISC/DSP system. The controller includes a keypad interface with hot keys for repetitious functions and DNC access to host computer. Memory for instant job replay, 32-bit processor, 12 MB RAM & 2 MB flash memory, interprets HPGL and M & G codes, RS-232 interface for PC communication. -- Includes:Surface Probe and Auto Calibration Sensor; Laser Pointer System; Dual Knife System (Electric Oscillating and Quick Change); K31 Multi-Tool Cutting Head; K41Knife Cutting Head; (1) 20 HP Republic vacuum blower for hold-down, (6) collets and tool-holder will be included.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5y 15 HP Fan motor, free-standing interior/exterior unit rated @ 3,900 CFM. Equipped with: (48) Filter bags having a total of 352 sq. ft. of cloth filter area in a fabricated steel enclosure; 12" dia. inlet. Magnetic starter; rotary air lock, estimated weight: 3,500 Lbs. Unit stands 13.5' tall when fully assembled, but with the legs and muffler removed, it can easily be transported on an open 5'x10' trailer. Machine State: Still in place, but disconnected NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

MURPHY-RODGERS HEC-216-S/10 33,000 CFM Continuous Duty Automatic Self-Cleaning Pulse Jet Baghouse Dust Collector Equipped with: (216) 5" Dia. x 10' L Cloth filter bags for a total of 2,827 sq/ff. of filter area. (2) 42-1/2" W x 68" H & (2) 40-1/2" x 68" H Top access doors. (3) Front & (2) side 27" W x 54" H Filter access doors. (2) Square cone bottom hoppers, Each with, 25" x 25" Discharge openings. System utilizes (2) 4-1/2’ x 6’ x 4’ H Waste containers (NOT included). CHICAGO 100 HP - 1,780 RPM Roof-mounted blower, with 41” Dia. inlet. Motorized dampers for winter & summer modes. Winter mode: Directs air back into building, reducing heat loss. Summer mode: Directs air outside, cooling building. Electrical controls (as pictured). Complete with: Spare Filter Bags. NOTE: Installed Used in 2016 with "New" 100 HP motor, new bearings in blower & "New" spring mounts. NOTE: Variable Frequency Drive needs to be replaced. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

MURPHY-RODGERS MRJ-610-122 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan.Specifications: -- 8,500 CFM approx. @ 9 to 1 air to cloth ratio baghouse dust collector with (60) 10-feet long filters; total cloth area of 943 sq. ft. -- Filter Cleaning: Continuous Self-cleaning Using Compressed Air. -- Main Fan: 30 HP top-mounted blower motor. with approx 18" dia. inlet. --System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, top safety railing, and approx. 16" Rotary Air Lock.Actual model is MRJ 610 -122.

MURPHY-RODGERS MRZ 17/16L Interior/Open 6 Bag Dust Collector with Auger and Rotary Air Lock General specs: Approx. 7,600 CFM @ 8" SP. (6) top filter bags @ 24" dia. by 72" long. (6) bottom disposable plastic dust storage bags. -- Fan/Motor: 25 HP BALDOR TEFC motor direct driven fan with electrical starter. 17" diameter inlet, with lifting hooks. The bag collector motor is brand new and has never been powered on or fired up. -- Comes with: Main approx. 17" dia trunk line, shut-off, and Quick clamp removal for filter and plastic bags. -- All steel construction with rugged support legs. Air Deflectors allows operator to adjust the air flow and amount of waste evenly into the 6 waste bags. -- Note: NFPA 664 (Fire Code) states that a max. of 5,000 CFM is limit allowed for indoor enclosure-less dust collectors.