CAM-WOOD - SET-48TS-CH 3045 , ...8 Heads Double End Tenoner for Chevron & Herringbone FlooringSpecial design Servo Control for Chevron & Herringbone Double End TenonerFeatures: -- Servo Control for + 30°,45° and 90° cutting. -- The automatic high-speed through feed device allows for perfect finishing at speeds ranging from 12 - 52 FPM. -- Feed chain with dogs at 12" center distance. -- Suitable for mass production of woodworking factory for processing of double end cutting, tenoning, grooving, moulding, and sanding. -- Possibility for: Scoring Saw, Trim Saw, Jump Coping, Shaper, Coping. -- Total (4) stations at each side. -- Reversed direction cutting jump shaper head with sensor for automatic move in and out for perfect cutting to prevent tearing at end edge. -- HMI Plus PLC controller for user-friendly easy setting and operation. -- Powerful machine is great for heavy-duty production. In addition to the double end cutting, all the settings and other processing can also be executed with high accuracy. -- Since the machine is so versatile, we believe it will be one of the most satisfactory machines for bulk production lumber-processing factories. -- The specially designed numeric controller allows quick setting of sizes for tolerance within 0.004";. -- Variable speed, through feed, wide rubber pad, and spring-loaded dogs conveyor for the best finish selections. -- Heavy-duty pressure rolls at top of wide width Conveyor to hold the material tight to prevent sliding during the cutting process. -- The Shaper head can be moved up & down, forward & backward. -- Equipped with: Industrial motors for full power cutting capacity. Specifications: -- Width from 30 mm to 305 mm (1.18" to 12") -- Max. working thickness: 2"; -- Working Lenght for 8" wide: 30° 30 1/4" to 33 7/8". -- Working length for 12" wide: 45° is 26" to 41" -- Working length for 12" wide: 90° is 13 3/4" to 49". -- Min. working length: 90° is 13-3/4". -- Scoring/Main saw blade (dia.): 10" x 1". -- Shaper cutter (dia.): 6" - 8" x 1" -- Feed speed 12' - 52', variable power 3 PH - 220/440 Volt. -- V-Scoring saw: 3 HP x 2. -- Trim saw: 3 HP x 2. -- Jump Shaper: 5 HP x 2 Stationary. -- Shaper: 5 HP x 2. -- Feed motor by Servo: 2 kW x 1; Width setting by Servo 0.75 kW x 2.Available Options: -- Total sound enclosure cover: Add ...$9,875 -- Infeed Hopper Magazine: Add ...$6,250.

CAM-WOOD SET-64TS-SH Double End Tenoner4-Head machine (two on each side) with Scoring/Cutting and HoggingCapacity & Style: -- Max. 72" working capacity, min. 12"; max. 4" opening, 24" load area in front of hold-downs. -- Single-post machine, single "dual-track" base, right side fixed, left side movable. -- Motorized opening with LED indicator.Each side equipped with: -- Scoring head, 3 HP - 3,600 RPM motor, and 1" dia. arbor for up to 10" blade. -- Hogging/cutting unit 5 HP - 3,600 RPM motor, 1" dia. arbor, 10" max. dia. cutter-head. -- Variable feed speed from 12 - 52 FPM, 1 HP motor, steel feed chains with plastic anti-slip pads, and dogs at 6" center. -- Spring loaded overhead hold-down beams with endless belts. -- Separate electrical control cabinet with operator controls.Options Available: -- Cross transfer system with transfer line 4' X 8' transfer table with rollers (additional $43,250). -- Hopper feed magazine (additional $4,450). -- 42" Infeed extension (additional $4000) -- Sound enclosure ...$7,675 -- Electric motor brake -- Central support

CAM-WOOD CS-650SCC Double End Matcher For Herringbone and Chevron FlooringNC Controlled Trough Feed Type End Matcher for Chevron and Herringbone flooringSpecifications: -- Working Width 1-1/2"; to 6"; -- Working Thickness 1/2"; to 1"; -- Working Length 8"; to 50"; -- Feed Speed 70 FPM with inverter -- Cycle time can be 4 to 8 second per piece1st Saw Station: -- Saw Blade Diameter 10"; -- Saw Motor 7-1/2 HP -- Feed Motor 1 HP with Gear Reducer & Inverter. -- Auto Stop & Align2nd Feeding Station: -- Feed Motor 1 HP with Gear Reducer & Inverter. -- Auto Stop & Align3rd Tennon Station: -- High Frequency HSD Routers with HSK63 Spindle, 11 kW (15 HP) x 2 units -- Forward and Reversed Direction at each spindle. -- Feed Motor 1 HP with Gear Reducer & Inverter. -- Auto Stop & AlignFeatures: -- Special Design CHEVRON & HERRINGBONE Double End Tenoner -- Servo control for 45° and 90° cutting. -- The automatic high-speed through feed device allows for perfect finishing at speeds ranging from 45 ~ 70 FPM by inverter -- Suitable for mass production of woodworking factory for processing of double-end cutting, tenoning, grooving, moulding, and sanding. -- Scoring Saw, Trim Saw, Jump Coping shaper, and Coping Shaper: Total 4 stations at each side. -- HMI plus PLC controller for easy setting and operation. -- It is a powerful machine great for heavy-duty production. -- In addition to the double-end cutting, all the settings and other processing can also be executed with high accuracy. -- The specially designed numeric controller allows quick setting of sizes for tolerance within 0.004";. -- Variable speed, through feed, wide rubber pad, spring-loaded dogs conveyor for the best finish selections. -- Heavy-duty pressure rolls at top of a wide conveyor to hold the material tight to prevent sliding during the cutting process. -- Shaper heads can be adjusted to move up & down, forward & backward. -- Features industrial motors for full power cutting capacity.Optional equipment: -- Total sound enclosure add: ...$ 7,900 -- Infeed magazine add ...$ 4,900

CAM-WOOD SET-46TS 6 Heads 48" Double End Tenoner: Trimming Jump coping and copingCapacity: -- Max. 48" working capacity, min. 12"; max. 4" opening, 24" load area in front of hold-downs. -- Motorized opening with LED indicator; -- Single-post machine, single "dual-track" base, right side fixed, left side movable.Each side equipped -- Top trim head, 3 HP - 3,600 RPM motor, 1" dia. arbor for up to 10" blade; (saw blade included) -- Jump coping head, 5 HP - 7,200 RPM motor, 5-7/8" (150 mm) long & 1 1/4" dia. arbor, 8" max. dia. cutter-head -- Coping head, .5 HP - 7,200 RPM motor, 5-7/8" (150 mm) long & 1 1/4" dia. arbor, 8" max. dia. cutter-head -- Variable feed speed from 12 - 52 FPM, 1 HP motor, steel feed chains with plastic anti-slip pads and dogs at 6" center, --Spring loaded overhead hold-down beams w/endless belts. -- Separate electrical control cabinet with operator controls. -- Sound enclosure

CAM-WOOD WX-1502H Horizontal GrinderFeatures: Impact-resistant tooling with excellent wear capability. Specifications: -- Horizontal feed, 20 HP - 1,750 RPM drive motor; 15-3/8" x 2-3/8" infeed chute; 8" dia. air discharge. Equipped with: -- (18) Rotary cutter sets with cutter head angle to allow aggressive cutting rates and high-speed shredding of waste; (4) stationary cutter sets; 10" dia. rotor; 575 RPM. -- The shaft rest for the cutter head is constructed by round hollow with special angle for cooling during production. Complete with: -- Removable screen for easy cleanup and chip size changes from standard 1/2". Includes: -- Operators' & Parts Manual and covered by (1) Year Warranty.

CAM-WOOD WX-4150 Vertical Grinder-ShredderImpact resistant tooling with excellent wear capability. Specifications & features: -- Vertical-feed Chute, 50 HP - 1,750 RPM drive motor; 41" x 12" infeed chute; (12) rotary cutter sets with cutter head angle to allow aggressive cutting rates and high speed shredding of waste. -- The shaft rest for the cutter head is constructed by round hollow with special angle for cooling during production. -- Complete with: -- Removable screen for easy clean up and chip size changes from standard 1/2". -- OutPut: -- 1,300 - 1,800 Lbs/Hr, depending on material and moisture content. -- Includes: -- Operators' & Parts Manual and covered by (1) Year Warranty.

CAM-WOOD WX-1504HC Horizontal Grinder w/ConveyorImpact resistant tooling with excellent wear capability. Specifications: -- Horizontal feed with (2) 1 HP infeed roller motors; 20 HP - 1,750 RPM drive motor; -- 15-3/8" x 4" Infeed chute; 8" dia. air discharge.Equipped with: -- (18) Rotary cutter sets with cutter head angle to allow aggressive cutting rates and high-speed shredding of waste; -- (4) Stationary cutter sets; 10" dia. rotor; 680 RPM. -- The shaft rest for the cutter head is constructed by a round hollow with a special angle for cooling during production. Complete with: -- Removable screen for easy clean up and chip size changes from standard 1/2". Includes: -- Operators' & Parts Manual and covered by (1) Year Warranty.

CAM-WOOD WX-1510 Vertical Grinder-ShredderImpact resistant tooling with excellent wear capability. Specifications & features: -- Vertical-feed Chute, 10 HP - 1,750 RPM drive motor; 15" x 11" infeed chute; (6) rotary cutter sets & (2) counter-knives with cutter head angle to allow aggressive cutting rates and high speed shredding of waste. -- The shaft rest for the cutter head is constructed by round hollow with special angle for cooling during production. -- Complete with: -- Removable screen for easy clean up and chip size changes from standard 1/2". -- OutPut: -- 300 - 900 Lbs/Hr, depending on material and moisture content. -- Includes: -- Operators' & Parts Manual and covered by (1) Year Warranty.

CAM-WOOD WX-4751 Vertical Grinder-Shredder Specially designed with push ram, powerful crusher for different materials such as wood, MDF, particle board, plastic, rubber, corn cob, etc. Specifications & features: -- Vertical Hopper 47" x 51"; 50 HP - 1,750 RPM drive motor; (96) rotary cutter sets & (6) stationary cutter sets; cutter-head angle cutting design allows aggressive cutting rates & high speed shredding of waste with maximum durability; 85 RPM rotor speed. -- The shaft rest for the cutterhead is constructed by round hollow with special angle to keep cooling for long hours of usage. -- Complete with: -- Removable screen for easy clean up and chip size changes from standard 1/2". -- Includes: -- Operators' & Parts Manual and covered by (1) Year Warranty.

CAM-WOOD WX-2404HCX Horizontal Grinder w/ConveyorImpact resistant tooling with excellent wear capability. Specifications: -- Horizontal feed with (2) 1 HP infeed roller motors; 30 HP - 1,750 RPM drive motor; -- 24" x 4" Infeed chute; 8" dia. air discharge.Equipped with: -- (30) Rotary cutter sets with cutter head angle to allow aggressive cutting rates and high-speed shredding of waste; -- (4) Stationary cutter sets; 10" dia. rotor; 680 RPM. -- The shaft rest for the cutter head is constructed by a round hollow with a special angle for cooling during production. Complete with: -- Removable screen for easy clean up and chip size changes from standard 1/2". Includes: -- Operators' & Parts Manual and covered by (1) Year Warranty.

CAM-WOOD IAT 620-150HX INVERTER DRIVEN FINGER JOINT SYSTEM Lay-Up and Block-Staging Infeed Conveyor: -- 24" Wide x 31.5" long belt conveyor powered with 1/2 HP motors. The conveyor is controlled by the operating and system. Feeds at a constant rate of 180 FPM. Block delivery is controlled by the operator and machine system criteria to feed the Shaper. The conveyor facilitates keeping the system full and productive. FSR-62I Right Hand Inverter Type Finger Joint Shaper: -- Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor and is equipped with provisions for vertical adjustment of 20 mm up and 20 mm down. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4"; maximum shaper cutterhead diameter - without knives. -- 5 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades. -- Conveyor powered by 1/2 HP motor. -- Table movement is inverter driven; powered by a 3 HP inverter motor with cycle speeds from 1 to 4 cycles per minute. Motor senses load and varies travel as needed. TC-62 Single Table Transfer Conveyor to the 2nd (Left Hand) Shaper: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeds at a constant rate of 180 FPM. FSL-62I Left Hand Inverter Type Finger Joint Shaper with Glue Extruder: -- Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4" Maximum shaper cutterhead diameter - without knives. -- 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP motor powers a top and a 2nd 2 HP motor powers a bottom scoring saw, both running at 2,850 RPM; accepts 7" dia. x 50 tooth x 5 mm blades. -- Conveyer powered by 1/2 HP motor. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and vary travel as needed. Speed is controlled by system criteria. Injection Type Glue Applicator: -- Extrudes adhesive into the fingers without a messy runoff. 6" Comb height is standard. Finger pitch 4 mm, 10 - 12 mm finger length is standard equipment (special sizes available as optional equipment) STC-62A Single Table Conveyor Belt to the Assembly Section: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeding at a constant rate of 180 FPM. FJ-500A (240") Assembly Press with Cut-Off Saw: -- Capacity from 1" to 6"; wide x 1/2" to 3" high x and from 6' to 16-1/2' long. motor powers the upper and lower pre-assembly driven by (2) 2 HP motor . -- 5 HP infeed inverter drive. In-feed speed from 30 to 230 FPM. Speed is controlled by system criteria. -- 5 HP - 2,850 RPM Cutoff saw accepts 14" dia. x 120 tooth x 4 mm kerf blade. Cutoff Saw c

CAM-WOOD HIAT-620-205 WITH 3"; HIGH X 8"; WIDE X 20’ LONG WORKING CAPACITIESTECHNICAL SPECIFICATIONS:Incoming Block Requirements: --Incoming block lengths from 6'' to 39"; (optionnal 122") --Blocks must be at least 50% longer than their width. --Block thickness from 1/2"; to 3 1/2" --Block width from 1"; to 8" - --Assembled lengths from 10’ to 20’ - 24’ Optional --For use with PVAC adhesives --Works equally well with soft & hardwoods. --Moisture content preferred from 8% to 12% --Blocks should be surfaced (4) sides to ± 0.2 mm with 90° right-angle corners. To be supplied by the customer: --Electric power supply to electrical cabinet --Constant voltage with deviations of 5% or less --Temperature range for computer control should not exceed 95°F. --Maximum humidity for computer control system under 65% --Hydraulic oil --Skilled operating and maintenance personnel --Motor Control Center with under-voltage and overload protection; includes UL and CSA approved electrical components. Electric parts only, not the complete machine. --Total electricity demand: 63.75 KW, 85 HP --30 HP Compressor with a 50-to-60-gallon Air Receiver PRODUCTION CAPACITIES:Shaper Capacity: --Shift = 480 minutes --Finger length to buyer’s requirement --As an example: 1-1/2"; X 5/1/2"; X 24"; average finished block size at the Shapers --Shaper max. speed of (3) table strokes per minute --Table cycles will change as block widths become “wider"; or “taller"; at the Shapers --Table accepts up to (16) blocks when vertical finger jointing 1-1/2"; X 5/1/2"; example blocks. --Table accepts up to (4) blocks when horizontal finger jointing 5-1/2"; x 1-1/2"; example blocks.Press Capacity: --Assembly Press w/2 operators: -- (4) Table loads per min. x 20’ lengths x 480 min. per shift x 0.8 rate of utilization = 30,720 lineal feet per shift OR 36,864 lineal feet per shift with 24’ Press)Production Calculations: --VERTICAL Finger Jointing w/2 operators: -- Capacity of the shaper when finger jointing 1-1/2"; x 5-1/2"; x 2’ long blocks: (3) tables stroke per minute X 16-blocks per table load X 2’ average infeed block length x 480 minutes per shift X 0.8 rate of utilization = 36,864 lineal feet per shift (63.34 M³) --HORIZONTAL Finger Jointing w/2 operators: -- Capacity of the shaper when finger jointing 5-1/2"; x 1-1/2"; x 2’ long blocks: (3) table strokes per minute X 4 blocks per table load x 2’ average infeed block length x 480 minutes per shift X 0.8 rate of utilization = 9,216 lineal feet per shift (19.46 M³) NOTE: Capacity is maximum as shown at Assembly Section and is dependent on blocks thru the Shapers System consists of

CAM-WOOD IAT 620-150H INVERTER DRIVEN FINGER JOINT SYSTEM 3" X 6":Lay-Up and Block-Staging Infeed Conveyor: -- 24" Wide x 31.5" long belt conveyor powered with 1/2 HP motors. Conveyor is controlled by the operating and system. Feeds at a constant rate of 180 FPM. Block delivery is controlled by the operator and machine system criteria to feed the Shaper. The conveyor facilitates keeping the system full and productive. FSR-62I Right Hand Inverter Type Finger Joint Shaper: -- Feed table is 24" wide and accepts blocks from 6" wide x up to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor and is equipped with provisions for vertical adjustment of 20 mm up and 20 mm down. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4"; maximum shaper cutterhead diameter - without knives. 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and varies travel speed as needed. Speed is also controlled by system criteria STC-62A Single Table Transfer Conveyor to the 2nd (Left Hand) Shaper: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeds at a constant rate of 180 FPM. FSL-62I Left Hand Inverter Type Finger Joint Shaper with Glue Extruder: -- Feed table is 24" wide and accepts blocks from 6" up to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4" maximum shaper cutterhead diameter - without knives. 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP motor powers a top and a 2nd 2 HP motor powers a bottom scoring saw, both running at 2,850 RPM; accepts 7" dia. x 50 tooth x 5 mm blades. Conveyer powered by 1/2 HP motor. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and varies travel speed as needed. Speed is also controlled by system criteria Injection Type Glue Applicator: -- Extrudes adhesive into the fingers without the messy runoff associated with glue rollers. 6" Comb height is standard. Finger pitch 4 mm, 10 - 12 mm finger length is standard equipment (special sizes available as optional equipment) STC-62A Single Table Conveyor Belt to the Assembly Section: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeding at a constant rate of 180 FPM. FJ-500A (198") Assembly Press with Cut-Off Saw: -- Capacity from 1" to 6"; wide x 1/2" to 3" high x and from 6' to 16-1/2' long. A 2 HP motor powers the upper and a 2nd 2 HP motor powers lower pre-assembly/crowder rolls. With 5 HP infeed inverter drive. In-feed speed from 30 to 230 FPM. Speed is controlled by system criteria. 5 HP - 2,85

CANTEK HB-800 32" Vertical Band Resaw32" Wheel diameter, 20 HP motor Vertical Band Saw;Specifications: -- 3.543" (90 mm) wheel width, 30-5/8" throat capacity, 15-3/8" under guide capacity. -- 4" Blade width X 216- 217-1/8" blade length. -- 20 HP main motor, generates a blade speed of 5,024 SFPM.Features: -- Heavy fabricated steel machine frame. -- Specially designed Bakelite guide blocks provide rigid side blade support for straight cutting. -- Large cast iron work table is precision ground & can tilt to a maximum of 45°. -- Convenient blade tension adjustment by means of a handwheel and gauge. -- Cast iron upper and lower saw wheels are precision machined and dynamically balanced. -- Rack & pinion blade guide adjustment. -- Wheel is crowned for proper blade tracking & added stability of the blade.Complete with: -- Foot brake for braking wheels & blade. -- Blade lubrication system and reservoir for lubricant keeps blades cool.Including Electrics to UL/CSA - all starters -- Auto Start-Delta control for main motor with Emergency Stop Switch -- Telemecanique brand magnetic switchHF-150A Feeder: -- 1 HP motor with variable feed speed from 16 - 66 FPM; 6" feed opening. -- Pneumatic tensioned feed roller. -- Feed pressure is adjustable. -- Feed roller opening & closing is controlled by a foot switch for operator convenience. -- Knurled steel roller.

CANTEK JF-330A Profile Knife Grinder Clamping length of 12" (300 mm) for both straight and profile grind; dia. of knife swing 12" (300 mm). -- Grinding Arbor: 3 HP grinding motor with VFD (LED Readout) drive from 1.500 to 4.200 RPM. Quick change removable (140 mm) wheel adapter. Machine set for axial constant grinding and template set up on right-hand side.Over the wheel precision diamond dresser assembly for dressing and dimensioning of wheel. Manual positioning: of grinding wheel to tool; positioning of back clearance angle and side clearance angle 5°/10° and 15°. Quick change stylus turret for applications; (6) included with machine. -- Carriage: SCHNEEBERGER linear bearing table movement. Table movement 12" x 6". -- Coolant system: 1/8 HP motor from coolant pump located in the tank below; (3) coolant nozzles for smooth flow of coolant to knife rest during grinding. Additional hose with nozzle for cleanup. Stainless steel splash guards throughout! -- Includes: Set up tools, coolant, HD worklight, grinding wheels and (1) arbor of choice - (1.25", 1.5", 40mm, 1-13/16", 2.125" or 50 mm).

CANTEK D405A 10' Sliding Table Saw Specifications: Max. cutting length 126". Max. depth of cut: 4.13" at 90° (355 mm), 5.12" at 90° (400 mm), 2.75" at 45° (355 mm). Main saw: 7-1/2 HP Motor, Blade dia. 16", Arbor dia. 30 mm (1.18"), Arbor tilt 0° - 45°, & Blade speeds 3,000, 4,000, & 5,000 RPM. Scoring saw: 1 HP - 8,000 RPM Motor, Blade dia. 120 mm (4.72"), & Arbor dia. 20 mm (0.79"). Equipped with: 15-1/2” x 126” x 35-1/4” H Precision anodized aluminum sliding table with Prismatic rollers running on precsion ground steel guides, 21.6” x 35” x 35.3” H Cast-iron fixed table, 12.6” x 32.7” x 35.3” H Auxiliary table. Main saw blade motorized height & tilt adjustment. 39-1/2” L x 3-1/2” H Aluminum rip fence, with 130 mm (51.18”) Cutting cap. Aluminum extruded crosscut fence, with (2) Flip stops with miter angle adjustment, & Sliding outrigger support. Eye-Level touchpad control, with LED Displays for main saw blade height & tilt. Overhead blade guard. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

CANTEK TA-14 Tilting Arbor Table Saw. -- Heavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 7.5 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK 1214 TABLE SAWHeavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 10 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK - PCM 120, ...Hollow Chisel MortiserFeatures: -- Power stroke of head permits easy, fast, and accurate successive cuts. -- Separate fan blower to keep work clean and free from dust & chips. -- Manual adjustable table height and lateral position. -- Heavy-Duty cast iron construction. -- Convenient centralized control panel. -- Foot pedal actuated cycle. -- Pneumatic workpiece clamping by lever.Specifications: -- Chisel range: 1/4" - 3/4"; Motor; 2 HP; Spindle speed: 3,400 RPM. -- Table: 16-3/4" x 21-1/4; Table tilts 30°. -- Air pressure: 8kG Clamping; Cylinder: 2-1/2"; (63 mm). -- Head traveling cylinder: 3.15"; (80 mm); Table cross travel: 5";. -- Table longitudinal travel: 18";; Table vertical travel: 12";. -- Max. stock width: 12";; Max. mortising depth: 4";. -- Machine weight: 572 Lbs. -- Shipping weight: 726 Lbs; Shipping dimension: 35"; x 38"; x 70"; (880 x 960 x 1,780 mm).

CANTEK - GOODSPEED CP-1250 AP Hydraulic Copy Lathe. -- General Data: 44" Length cap. with 4" min. length of stock and 1/2" - 4" max. diameter cap., hopper feed with automatic chucking, square or round stock can be hopper fed. -- Equipped with: 7.5 HP Spindle motor, 1,800 - 3,200 RPM spindle speed adjustable by pulley change, 3 HP hydraulic motor. -- Complete with: Swivel control panel, PLC sequence controller built into separate control cabinet, (3) pressure gauges, automatic way & support collar lubrication & safety wire mesh across the front of machine. -- Includes: Two hydraulic copiers (rough + fine). Travelling steady rest and installed knives. -- Production capacity: Approx. (5 - 7) pieces/Min for 600 mm length, (3 - 5) pcs./Min for 900 mm length, (2 - 3) pcs./Min for 1,200 mm length, depending on cutting speed, type of material, etc. -- Electrical load: 11.4 amps, 10.5 HP @ 575/3/60.volts.