DIEHL - SL-52, Straight Line Rip SawSpecifications: -- 15 HP Motor, 3,600 RPM belt driven, fixed 2" arbor. -- 14" to 18" Blade diameter. -- 4-1/4" Max. thickness with 18" blade diameter. -- 2 HP - 1,800 RPM feed drive, variable feed speed from 65 to 190 FPM. -- 25" Throat depth to right of blade, 24" of table to left of blade. --Table size: 61" x 80".Equipped with & Features: -- Cast iron pressure bar arms with ball bearing rollers. -- Adjustable rip fence. -- Self-adjusting antikickback fingers with control cam. -- Automatic lubrication of feed chain & race. -- Full overload and under voltage protection. -- Manual arbor brake for safety with interlock.NOTE: From the seller Glue Line . Fence not shown in photo as was removed for transport, but is completeShipping Dimensions 7-1/2' L x 7' W x 5-1/2' H; weight of 5,000 Lbs.

DIEHL - SL-62WA: Straight Line Rip Saw (Wide Arm Model)20 HP Main saw motor; 2" arbor.The chain on this "SL-62 WA" has": 90% + Chain life or better left. - This is a "Glue Line" capable machine.Specifications --Table measures: 95″ x 79″; Fence locks: 56″ To the right of the blade with 56" total of clearance from the right of the blade to the upright supports. -- 4-1/4" Max. depth of cut. -- Stock thickness cap.: 1/8" Min. to 4-1/4" max. -- Everything raises & lowers throughout its range very easily.Feed -- 2 HP Variable speed feed: 65 to 195 FPM. -- Automatic Lubrication System. -- Automatic chain oiler.Equipped with & Features -- Spring-loaded rip fence. -- Anti-splinter kickback fingers. --Front push button controls. -- Laser light.

DIEHL SL-55 Straight Line RipsawSpecifications: -- 15 HP - 3,450 RPM Direct drive arbor motor, 2" dia. arbor, 16" blade cap. -- 4" Max. depth of cut, 12" min. part length -- 20-1/2" width of the table to the right of blade & 30" to the left, 66" table length.Equipped with & Features: -- 3 HP 4-Step feed drive 30 - 50 - 75 & 120 FPM; -- Twin chain drive. -- Automatic drip chain lubrication. -- Top pressure system with (6) full-width rollers & (2) split rollers over the blade.

DIEHL - TFM-68, ...4"; x 8"; 5-Head High Speed Jointed Moulder5-Head (B-R-L-R-T-B) with 8-5/8" x 4-1/2" capacity. Head sequence: Bottom 15 HP, Right 10 HP, Left 10 HP, Right 10 HP, Top 15 HP, and Bottom 20 HP motor.1st Bottom and 1st right side run at 3,600 RPM; all the other spindles run at 6,000 RPM utilizing the included Frequency Changer.Side heads tilt 35° inward and 5° outward. Specifications: -- Spindle diameter: Vertical 1-13/16"; Horizontal 2-1/8" dia. for top spindle only. -- Built-in straight & profile jointers on spindles 2 - 3 - 4 & 5. -- Variable feed speed from 20 - 150 FPM via 15 HP feed drive. -- Cardan Shaft driven. -- WAXLIT Pump and groove bed with groove cutters for 1st bottom. -- Air chipbreakers and feed roll tensioning. -- Starting panel and transformer included.Weight: Approx. 14,000 Lbs

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6g DIEHL NO. 75 18" Straight Line Rip Saw Specifications: Table size 52-1/2” x 80” x 34” H. Throat 21". Distance from front of blade to table 36". Max. blade dia. 18". Adjustable arbor dia. 2". Min. stock length 12". Max. stock thickness 4-1/4". Max. depth of cut 4". Variable feed speeds 40 - 145 FPM. Equipped with: 15 HP - 3,500 RPM Blade motor. Automatic arbor brake. 8-1/4" W Dual 4" W Pyramid corrugated feed chain, with 3 HP Motor. (8) 8” W hold-down rolls, Each with (4) 1-1/2” W Segments. Upper anti-kickback fingers with Cam height control. Automatic lubrication. Complete with: 29” W x 1-3/8” H Cast-Iron Fence.

DIEHL ESL-10 Straight Line Rip Saw, with Laser Specifications: Table size 39-1/2" x 52" x 35" H. Throat 17-1/2". Distance from front of blade to table 21-1/2". Max. blade dia. 16". Max. thickness 1-1/2". Guaranteed glue joint length 48". Feed speed 30 FPM. Equipped with: 10 HP Blade motor with Automatic brake. Pyramid corrugated feed chain, with 1 HP Motor. (5) Pairs of 2-1/2” Dia. x 1-1/2” W Hold-down rolls. 20-1/2” L x 2” H Fence. Upper & Lower anti-kickback fingers. Manual feed chain lubrication. Complete with: Installation, Maintenance & Operating Instructions. Laser. 11-3/4" Dia. Blade. (4) Swivel Casters.

--In auction: https://exfactoryauctions.com/Detail/SO-230040/event/A122024$1- NO RESERVE!-- GRECON/DIMTER OPTICUT 204 L Optimizing Cutoff System NOTE: Currently De-installed Specifications: For hard or soft wood. Left-to-right feed. Max. crosscut section 7-3/4" x 1-15/16" to 5-3/4" x 3-1/16". Board width cap. 1-1/5" to 7-3/4", Board thickness 3/8" - 3-1/8", Board length 15" to 20'. Shortest fixed length 5-3/8", Shortest finger jointing length 5". Max. feed speed 750 FPM. Average production rate 36,000' running length/shift. Equipped with: Blade dia. 19-1/2", with 10 HP - 4,100 RPM Motor. 10 HP Servo drive feed motor, (3) Pneumatically-operated top rollers & (1) Driven bottom drum roller. Control, with LCD display & Touchpad. Complete with: 12" W x 23-1/2' L Infeed Belt Conveyor, with Double wheel measuring system & Top mounted luminescent camera, Detects crayon defect marks up to (8) grades. 12" W x 34-1/2' L Outfeed Belt Conveyor, with (4) Sorting stations, with Encoder pulse-controlled kickers, Kick singularly or in batches of 2 or 3 for larger heavier boards. PC-Based Control.

Dincmak Model DMT120 Double Sided Slot MortiserSpecifications -- Max Mortise Width: 120mm --Max Depth: 50mm --Max Workpiece Height: 100mmEquipped with and Features -- Two Independent Working Table w/ up to 45 Degree Tilt -- Oscillation Motor: 3/4HP (.55kW) -- Cutting Motor: 4HP (3kW)

DIXIE - 15 HP: Dust Collector Specifications -- 15 HP Motor. -- 1,760 RPM. -- Air Pulse filter bag cleaning System. -- (2) Bottom outlets. -- 15" Diameter: Inlet pipe size. -- Wall-mounted motor control station. -- Overall Collector footprint: 90" Wide x 67" deep (101" with rear-mounted fan) x 122" high.

DONALDSON/TORIT - WSO 20: 1,230 CFM, 3 HP Floor Mounted Mist Collector with After-FilterSpecifications -- Filter height: 20".Complete with: -- Top-Mounted after-filter.

DONALDSON/TORIT - DRYFLO DMC-C: 3 HP Mist CollectorSpecifications -- Filter area: 13 m² (42 sq./ft.).

DONALDSON / TORIT DWST6-5 Cartridge Dust CollectorDownflo® WorkStations (DWST) fit anywhere on the plant floor and apply NO restrictions to worker movements or visibility. The full line of WorkStations are designed specifically for those in-plant areas where dirty and/or noisy operations are out in the open—grinding, sanding, chipping, batch mixing or welding. The DWST delivers exceptional performance in metalworking, woodworking, and process applications where high filtration efficiency and ledge less construction is often a requirement. Specifications: -- (5) Module System, each with 10 HP motor, 7,000 CFM. -- (4) Ultra-Web cartridges. -- Pulse-cleaning manifolds and ventures, (2) dust drawers. -- (1) Acoustical panel per module. Louvers mounted on lower section of unit.Includes: -- (1) IEC control panel includes 460-volt motor starters, circuit protection for each motor, transformer, programmable logic controller. -- Magnehelic gauge mounted in a panel door, start/stop buttons, and a through-the-door disconnect switch. -- Pulse cleaning can be continuous or after-shift. -- All components are IEC rated. The enclosure is rated Type 12. -- 1"; Compressed Air Regulator with Filter Separator and Gauge, Black Iron Fittings, and Black Iron Piping Required for Cleaning System. -- Provides a 1"; Common Connection Point for Design Shutters to Tie into with Existing Compressed Air System.

DOOSAN DX-180LC-3 Crawler Excavator Specifications: -- Engine Model: DL06 -- Gross Power: 122 HP -- Track Size; 24" -- Bucket: 42" -- Max Cutting Height: 29.37ft inJ -- Max Loading Height: 20.54ft inK -- Max Reach Along Ground: 28.19ft inL -- Max Vertical Wall Digging Depth: 15.29ft inM -- Max Digging Depth: 18.77ft in -- Operating Weight: 38933 Lbs -- Fuel Capacity: 74 galEquipped with: -- Auxiliary Hydraulics -- Hydraulic Quick Coupler -- Hydraulic ThumbNote: Hours approx. 4,165 and being used.

DOOSAN - DX85R-3: Compact Crawler Excavator with Brush CutterSpecifications -- YANMAR Engine: 59.4 HP (44.3 kW). -- Max. torque: 1,365 RPM; 24.6 kGf/m (241 Nm). -- Max. swing speed: 9.5 RPM -- Boom swing angle: L/R 70° / 55°. -- Travel speed: (Low - High) 1.6 to 2.92 MPH (2.7 - 4.7 km/Hr). -- Max. gradeability: 35° / 70%. -- Hours: 350 (in use).Equipped with: -- 50" MTL "XC5 Brush Cutter. -- 60" Ditching bucket. -- 36" Digging bucket. -- 24" Digging bucket. -- Hydraulic quick coupler. -- Hydraulic thumb. -- Front blade. -- Roll Over Protective Structure (ROPS). -- Pressurized, sound insulated Cab. -- Adjustable seat with adjustable: Headrest and armrest. -- Air conditioning. -- Pull up type front window & removable lower front window. -- Sliding right windows with lock. -- Ceiling light.

DOOSAN DX300LC-3 LONG REACH ExcavatorSpecifications: -- Engine Type: Doosan Horsepower: 213 HP (159 kW / 216 PS) -- Engine Cylinders: 6 -- Boom reach: 60' -- Track width: 33.5" -- Hours: 2,800Equipped with:60 ft long reach boom60" Bucket

3-1/2’ x 7’ and 3-1/2’ x 8’ Double-Sided Hydraulic Door ClampEquipped with: -- 5 HP Hydraulic Unit.

DOUCET - MSB-ESB 16-G: Panel Sequencer (Edgebander & similar application)Model "ESB" increases the productivity of your Edgebander by: Maintaining the gaps between parts to their absolute minimum. -- It allows the Operator to stage several panels in its bottom feed magazine. -- Panels are released automatically as soon as the preceding one clears; the "no feed zone" on your Edgebander or feed end-to-end on your Shaper-Sander.Specifications & Operation -- "ESB 16" Features: 16" Wide x 54" long feed belt. -- Suitable to feed panels ranging from: 4" x 10" to 24" x 84" at up to 100 FPM. -- Feed hopper offers: Reserve capacity up to 12" thick or a max.150 Lbs. -- Sequencing of panels "fed lengthwise" is fully automatic. -- Sequencing panels "fed width-wise" or of panels larger than those described above require the assistance of an Operator. -- This model is made for left-hand feed EdgebanderNOTE: New feed roller installed lately at ...$ 1,600 cost.

DOUCET - X 60: Finger Jointer Line for Medium Production"X 60 DG" Automatic feed Finger Jointer has Chain Feeding System: Driven on the bottom & right-and-left side; feeds board up to 6" max. width. Capacity -- 3/4" - 2" Max. thickness; 1-1/2" - 8" max. width with: Lugs on 11" centers; 5" min. - 48" max. material length. "X60" Right Hand Shaper Sections; equipped with: -- 5 HP Trim Saw; 3 HP scoring; 15 HP Shaper motor. -- PLC Controls on Shaper section. -- Dual feed chain with: Lugs on 11" centers; 10 - 75 FPM variable feed speed; 5 HP feed drive. -- Max. width: 8"; thickness from 3/4" to 3 1/2". -- PLC Controlled extrusion type Glue Applicator with: 12-Gal. tank; sound enclosure, & cabinet type base. - Transfer to the Assembly Press. Model "MP-32" Assembly Press -- 7' - 10' Max. in automatic mode & up to 20' in manual mode cutoff cap.; automatic cycling; 90 FPM powered infeed flat top chain with: Side alignment rolls to the preassembly tunnel. -- Pieces are fed through with: Bottom & side chain through the Cutoff Saw to a movable limit switch and cut to length; 5 HP upcutting Cutoff Saw for continuous assembly; 2" x 9" cap. with: 14" Blade; finished lengths are pushed out by the next piece onto material outfeed arms. -- PLC Controlled Press section; 10 HP Hydraulic unit; 10,000 Lbs max. pressure. -- Gluing system with pump.System Includes & Supplied with: -- Stainless friction plates on assembly table; board holddown on all (4) sides. -- Automatic ejection of finished board with table. -- 6-Bolt cutterheads for hardwood and softwood.Production Capacity: Approx. 8,000 linear ft./shift or more; based on 12" average infeed length.

DOUCET RDM Rotary Miter Door ClampMax. cap. of 36" x 72" per squaring assembly. -- Single door clamp design which allows you to clamp & square doors at one time or large doors up to 72" L. -- This machine offers precise & accurate squaring of stile & rail cabinet doors. In addition with the rotating design you can achieve high production. Includes: -- (5) Rotating pneumatic sections; each section with pneumatic squaring assembly, (2) horizontal & (2) vertical clamps; foot pedal control for rotation with 1/2 HP motor drive unit. -- Actual Model # "RDM-M-5-36-72"

DOUCET RDM Door Master Rotary Door Clamp 5-Station Rotary Door Clamp Capacity & Features: -- Max. cap. of 36" x 96" per squaring assembly; Minimum 5.5" X 24", 2-1/2" jaws -- Single door clamp design and the rotating system offers high production. -- This machine offers precise & accurate squaring of stile & rail cabinet doors. Equipped with: -- (5) Rotating pneumatic sections; each section with pneumatic squaring assembly, (4) Adjustabler horizontal & (1) fadjustable vertical clamp -- Push button control for rotation with Heavy Duty 230V, 3-Phase gearmotor drive. -- Made of 100% welded tubular steel construction; Tear down not included in price.