TIMESAVERS 43- 3 OB Orbital Sander3-Head, 43" width cap. with (2) Orbital heads and (1) finishing brush. -- 1st & 2nd Orbital Heads: Each orbital head with (1) 10" wide platen for a total of (2) platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- "Quick change" system for abrasive material, (2) 7.5 HP main orbit motors, and 1 HP oscillation motor. 3rd Head: Rotary abrasive brush with 2 HP motor, single side brush wear/height adjustment. -- Conveyor belt feed with Ruff-Tex conveyor belt, variable feed speed from 5 - 20 FPM, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening, constant pass line-height of conveyor bed assembly, extended infeed load area, motor load meters on sanding heads. -- Includes a DOUCET Return Conveyor System -- New transformer for 230 or 460 Volt, specifically for this machine is available at an additional cost

TIMESAVERS 52-20 ORBITAL SANDER2-Head, 52" width cap. with (2) Orbital heads.Specifications: 1st & 2nd Orbital Heads: Each orbital head with (2) 5" wide platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- 1st Head: 7.5 HP 230/460V 3PH motor -- 2nd Head: Oscillating platen 7.5HP, 330/460V, 3Ph"Quick change" system for abrasive material -- Conveyor belt feed with Ruff-Tex conveyor belt, variable hydraulic feed speed from 5 - 20 FPM, vacuum bed assembly, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening with mechanical digital readout, constant pass line of conveyor feed bed assembly, motor load meters on sanding heads -- Push button controlsNOTE: Feed Motor and Feed Belt have been taken apart for shippingThe above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify.

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included

DONALDSON-TORIT: 376RFW-10 or 12: Dust Collector45,000 CFM @ 9.7:1 Air-to-cloth ratio; 140" dia. round baghouse with: (376) Filter bags of 10' length (oval bags provide for radial movement of bag during cleaning for longer life); total 4,632 sq./ft. filter area. -- Filtration media cleaning via: Floor mounted 7-1/2 HP medium pressure Air Pump (eliminates the need for compressed air; can be susceptible to condensation & freezing); 36" x 65" return air outlet; 48" x 48" inlet for dust laden air. -- Includes: Rotating cleaning air manifold driven by 1/3 HP motor; (1) NEMA-9 solenoid & diaphragm valve, which rotates over the bag openings; walk-in plenum for bag access/maintenance. -- Galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed; walk-in access door at top of ladder. -- Equipped with: Structural steel support; maintenance platform; caged ladder; bolt-on involute arm; explosion doors (need to be replaced). -- Includes Backward inclined FAN EQUIPMENT: Size 7 BCS floor-mounted Fan set at 45,000 CFM @ 15" SP; belt driven at 1,485 RPM; powered by a 200 HP TEFC Motor via OMRON/IDM E7 Series Inverter. -- 24" Rotary Air Lock at the bottom of the 60° hopper. -- Complete with: Pictured electrical controls are included. -- NOTE: New 200 HP electrical motor was replaced recently. -- Unit had an accidental fire at bottom section near Hopper causing the explosion doors to burst. Unit still working as they are not returning the air. Can be sold with or without replacement of doors; cost of which is negotiable. -- Professional dismantling and rigging available at extra cost. Please call!

TORIT - CHECKER BOARD: Control PanelTORIT Checkerboard Control Panel for a "DFT3-18" Dust Collector up to a 25 HP Blower.Includes -- Start/Stop push control buttons for Dust Collection System. -- Electric disconnect to shutdown power if needed. -- HEPA Filter pressure gauge. -- Alarm with light when dust filters require cleaning. -- Pressure gauge showing the air flow in the system. -- Air pressure pulse cleaning controls to clean dust from filters. -- Control box mounted on legs.

TORIT - 460-IRD-20: Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Downflow air pattern allows airflow & gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure drop.Specifications -- 20 HP Direct drive; floor mounted blower. -- Fan inlet: 17". -- CFM: 7,000. -- Set of filter bags. -- Steel elbow from fan to collector. Motor Starter included.

TORIT 360-IRD-15 Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Down flow air pattern allows airflow and gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure dropSpecifications: -- 15 HP direct drive, floor mounted blower. -- 4,800 CFM @ 8" wg, 4,050 CFM @ 9" wg, 2,400 CFM @ 10" wg -- (21) Dura-life filter bags with a cloth area of 192 sq. ft. -- (3) Collection points for plastic collection bags.

TORIT-DONALDSON ADMC AD8 DRYFLO Cartridge Dust Collector. A Mist collector designed for long-lasting high collection efficiency capture of coolant and machining oil mists in metalworking applications. Even smaller amounts of dust can be filtered in the dirty air stream. -- DRYFLO is a proprietary cartridge which outperforms electrostatic precipitators and mist collectors utilizing standard HVAC envelope and cassette filters. Filter unit features a unique air-side filter retention system allowing for quick filter changes with minimal worker contact with collected oil. -- Also feature three-stage Filtration via a.) prefilter, b.) wrap allowing, c.) the filter cartridge to drain and coalesce smaller coolant mist droplets in to larger droplets. Plus optional fourth stage HEPA filters available for applications where smoke exists or additional efficiency of discharge air is required. -- Overall data: Capable of 17,600 CFM; (8) Filter Cartridges, 1,760 sq. ft. of filter area, -- Complete with: Ground mounted fan powered by a 40 HP motor, belt-driven. Fan includes a variable volume inlet. In prior application clean air was not retruned to building. -- Blower currently setup for approx. 15,000 CFM with 40 HP, Baldor Super-E, 324T frame, 1.780 RPM motor. -- Enclosure dimensions: 133" long, 68" deep, 160" high. Filter weight is 7,300 lbs.

TORIT - 460-IRD-20: Dust CollectorAn easy & economical solution for a wide range of wood dust collection applications. Downflow air pattern allows airflow & gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure drop.Specifications -- 20 HP Direct drive; floor mounted blower. -- 1/3 HP Shaker motor with auto controls. -- Fan inlet: 17". -- CFM: 7,000. -- Set of new filter bags. -- Steel elbow from fan to Collector; Motor Starter included. -- Existing ductwork available as shown in photos. Collector has been disassembled for shipment.

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

TREMZAC 248-TR-CO Portable Shaving Mill [email protected] supply; 65 HP from P.T.O. of tractor at 540 RPM (not included ). -- Emergency shutdown included. -- Log; 5" to 22" in diameter x 96" long. -- Capacity ( shaving ) 5 to 19 cubic yards/hour. -- Hopper Magazine; 24" wide x 96" long. -- Double Axle Trailer with hydraulic brake included. -- Cutter head 24" with (8) knives -- Dimensions; 7' 3"' wide x 31' 3" long.

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

TYLER - 2400: Slat-Wall Machine -- SpecificationsProduces T-slots "Slat-Wall" for architectural/store fixture panels.48" x 97" Max. panel capacity., 24" x 24" min. cap., panel thickness 1/2" to 1-1/2". Machine capable of processing up to (40) panels/Hr; depending on material density, thickness, and the slot profile. -- Equipped with:Machine is currently setup with: (18) Router spindles on 3" centers.Spindles are driven in groups of (3) with: (6) 7-1/2 HP - 3,450 RPM Motors that drive the (18) router spindles; all router spindles rotate @ 15,400 RPM.Machine can accept up to (21) router spindles & the additional spindles can be activated by adding (1) additional 7-1/2 HP - 3,450 RPM motor. -- Machine Operating SequencePanels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return,Variable feed speed control, router assembly traverses on ground & polished rails with chain drive.Panels are positioned along the 8' rear edge fence line; distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Operator & Machine ControlALLEN-BRADLEY Electrical controls for the machine cycle; "setup" mode of operation.Machine cutting cycle is initiated by: 2-Hand Operator safety buttons located on the right front of machine. -- Complete with:Overhead holddown assembly with: (2) Large air cylinders; (6) arms with spring loaded clamping pads hold the panel in place.Panels are loaded from the 8' front and exit to the side for easy unloading. -- Options Include: Assortment of used "Diamond Tooling" (diamond router bits) Assortment of extra motors Spare parts Service manual & docs. -- Actual Model: TYLER 2400

TYLER 703 Power Pod Cold PressTyler Air Pod Press with a Platen dimension of 40″ Wide X 87-1/2" Long. -- The Maximum Daylight Opening is 49.5″, and the pods will extend 9.5″ for a minimum opening of 40″. -- The top and bottom plates are dent free. -- The press is rated to 100 PSI and has (1) pod short of 100% pod coverage (being that the center bags are staggered). -- There are spring loaded bed rollers to aid in loading and unloading. .This machine has been cleaned and checked and there are no air leaks.

--In Auctions; https://exfactoryauctions.com/Detail/DL-230113/event/A122024$1 - NO RESERVE -- TYLER French-Type Dovetail Machine Equipped with: (2) 14-1/2” x 17” Tables. (2) 2 HP Routing heads for mounting of drawer sides. (1) 2 HP Grooving head for drawer bottom dado, (2) 2-Spindle Vertical boring heads for drawer hardware. (2) Pneumatic hold-down clamps

UAS -BHT (CALCOR) MIB-11-T19- SVA Pulse Jet baghouse dust collector. MIB is Modular Industrial Baghouse. -- Has qty (18) each of filter cartridge # 04007500 (6.125 x 75") and qty (18) each of filter cartridge # 0400000249 (6.125 x 41.6250"), for a total 1,896 sq. ft with pleated Spunbonded Polyester w/PPTFE filter bags. -- OEM rated for 5,000 ACFM @ 11" SP, resulting in a 2.64 Air-to-cloth ratio. -- 20 HP Siemens motor, on a large floor-mounted blower -- Comes with DPC and Timer board for Pulse Cleaning Control. Allen Brady Starter and air quality motoring. -- Discharges thru Pyramid hopper into a 55 Gallon Drum. Includes dome style explosion vent.. -- Housing dimensions: 60" x 60" x 232" high. Total weight with filters: 3800 Lbs. -- Looks like its brand new. -- Last used for a CNC Laser Cutter.

UHLING - HP 4000, ...Case Clamp (Semi-Automatic) -- Specifications100" Wide x 50" high x 24" deep clamping cap. and built with a Heavy wall steel frame construction. - Super "easy & quick" manual positioning of vertical side pressure carriage and top pressure beam. -- Includes: Push button release, pneumatic locking and "counterbalanced" movement of horizontal top pressure beam; vertical side pressure carriage with single lever release & lock; locks in place with (4) air cylinders and rides on bearings for quick & easy positioning. -- Vertical & horizontal pressure beam equipped with: (5) Adjustable "dual" ram air pod pressure shoes (3 on the top horizontal beam & 2 on the side vertical beam); 3-1/2" clamping stroke; features individual air pod selection. -- Since the pressure bar is positioned over the joint (or shelf), it will automatically compensate for sizing inaccuracy. -- Independent controls for top & side pressure and timer for clamping cycle; solid bottom & back support for any size case. -- Air flow pressure controls & pressure gauges built into traveling vertical carriage (always close to the Operator). -- Overall dimensions: 143" x 90" x 30".

UHLING - HP 2000: Case Clamp (Pneumatic) Specifications: -- Offers a compact, quick, and easy-to-use Case Clamp. -- 50" x 42" x 24" Clamping cap. that handles ...80% - 90% of your case good needs. -- (2) Counterweight-balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with: Individual controls for each air pod pair. -- Roller bearing mounted carriage with: Pneumatic locks. -- Single-lever lock or unlock control; front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access Operator's Control Panel that is mounted on the vertical beam.

UHLING - HP-3000: Case Clamp (Single-Bay) -- SpecificationsClamping capacity: 72" L x 74" H x 24" D; Large enough for multiple boxes; offers versatility, quick 30-Sec setup or changeover. -- Pressure Elements(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; just position them effortlessly and let go: Counterweight will keep them in place; no need to secure them! -- Air Pod Stroke3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical BeamMoves easily on roller bearings; pneumatic carriage locks with: (4) Small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam so it is always where it is needed; single lever lock-or-unlock control & front/rear pressure selection. -- Counter SupportBy solid laminated panel opposite to pressure bars. -- Actual Model is: UHLING HP-3000