TIMESAVER - 113, ...12" Width Single-Head Wide Belt Sander12" Width cap., single drum.Specifications: -- 12" Width capacity. -- 7.5 HP Main motor. -- 6" Dia. drum. -- 0 - 8" Opening capacity. -- 0.5 HP Feed motor. -- Complete with: Posi-Trac electronic tracking and a 12" conveyor extension.

TIMESAVERS 150-1v Wide Belt Sander;1-Head, 50" width cap.; contact roll head with 40 HP motor; 50" x 103" abrasive belt size, air tracking, 2-1/2" max. thickness cap., adjusted by scale; variable feed speed 40 to 100 FPM; incl. in- & outfeed extension. -- Used to have a checkrail edge sanding attachment for sanding sash (no longer available), but includes (1) extra set of new conveyor belts.

TIMESAVER - TB-440-4, ...2-Head Wide Belt Sander40" Width cap.; Drum and Combination Head.Head Configuration:1st Head - 50 HP; 12" rubber covered contact head.2nd Head - 40 HP; combination platen head.Specifications: -- Sander completely rebuilt (15) years ago. -- Rubber covered abrasive rolls were recovered, grooved and balanced, along with ALL pinch rolls recovered at FLETCHER MACHINE CO., Lexington, NC. -- Electric eyes upgraded to BANNER's send and receive type; includes battery backup system for controls (no crashes when machine has power outage). -- Feed speed gear box driven by AC Drive controlled 10 HP motor. -- Rebuild included: Table removed and platens ground flat; all bearings replaced, including pinch rolls and tracking cylinders; tension cylinders plasma sprayed, reground & new factory seal kits. -- Entire machine was disassembled, sand blasted and DUPONT "Zolatone" primed and painted. -- RAINBOW brand feed conveyor belt replaced in 2014. -- Many more upgrades, too many to list: Please contact for additional information. -- Machine is in good condition, running daily, and has had regular recommended service intervals; includes all factory manuals, blueprint drawings, parts list with numbers supplied, and when machine was new. -- Machine used in solid wood wide belt sanding. -- Includes Cloth aluminum Oxide Belts: 7 - 50 grit; 1 - 60 grit; 8 - 80 grit; 2- 120 grit; 8 -1 80 grit..

TIMESAVER - 337-2, ...2-Head Wide Belt Sander36" Width cap., Drum & Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Rubber contact Roll & Platen 30 HOSpecifications: -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP Feed drive; Variable feed speed from 20 - 60 FPM. -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, 0" - 6" opening. -- Infeed safety stop bar. - Also has adjustable shoes before and after each head. Equipped with & Features: -- Controls mounted on belt loading side. -- Sanding head motors with air caliper disc brakes --Motor load meters.

TIMESAVERS 237-4IC Four-Head Wide Belt Sander37" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Rubber covered contact roll, 9-1/2" dia., 30 HP motor;2nd Head: Rubber covered contact roll, 9-1/2 " dia., 25 HP Motor. 3rd Head: 9-1/2" Grooved Rubber Covered Contact Drum With A 20 HP Motor4th Head: Finishing platen, 2-1/2" wide, 20 HP motorSpecification -- 37" x 75" abrasive belts with Pneumatic tracking. -- Motorized part thickness adjustment, height, 0" - 6" opening. -- Automatic part thickness adjustment, -- Infeed & outfeed spring loaded holddown shoes, -- Variable feed speed from 15 - 45 FPM, 5 HP motor. -- Pneumatic feed beltEquipped with & Features: -- Motor load meters, -- Infeed emergency stop bar, -- Controls mounted on belt loading side, -- Automatic Trabon bearing lubrication system, -- Disc brakes on sanding head motors, -- 30" infeed load area.Note: Some spec's need to be verified

TIMESAVER 337-2 Wide Belt Sander, (2) Heads36" Width cap., Drum, Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Drum with Platen 30 HP motor. Specifications -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP feed drive; Variable feed speed from 20 - 60 FPM.Equipped with & Features -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, -- 0" - 6" opening. -- Infeed safety stop -- Adjustable shoes before and after each head. -- Controls mounted on belt loading side, --Sanding head motors with air caliper disc brakes, and motor load meters.

TIMESAVERS 252-4-IC, ... Wide Belt Sander, 4-Head.4-Head, 51" cap. - Great sander for solid wood and veneer panels equipped with (2) Contact rolls and (2) Air platens. Head Configuration1st Head: Rubber covered contact roll, 9-1/2" dia. 60 - 70 Durometer, 40 HP motor.2nd Head: Rubber covered contact roll, 9-1/2" dia. 50-60 Durometer, 30 HP Motor.3rd and 4th Head: Finishing platens, 2-1/2" wide "Veneer Saver" inflateable platens with adjustable timers for leading and trailing edges, 20 HP motor each head.Specifications: -- 38" Constant pass line height of Vacuum conveyor with suction fan and motor bed assembly for veneer and solid wood sanding. -- Adjustable air floating infeed and outfeed hold down shoes. -- 52" x 103" abrasive belts with "POSI-TRAK" electronic tracking.Equipped with & Features: -- Motorized part thickness adjustment with mechanical digital readout. -- Auto part thickness set-up, 0" - 6" opening. -- Hydraulic feed belt operation of 15 - 45 FPM via 7-1/2 HP hydraulic pack. -- 4-Motor load meters, controls mounted on belt loading side. -- Disc brakes on sanding head motors. -- 30" Infeed load area.

TiMESAVERS - 237-KA IC, ...Planer Sander w/2-HEADs 2-Head Planer Sander Combination; 37" width capacity.Head Configuration: -- 1st Head. 7" Dia. Helical "Quiet Cut" planer head with: (6) Spirals of 4-sided carbide inserts with 15° rake angle; head turns @ 3,200 RPM; head adjustment with dial indicator readout; 30 HP motor. -- 2nd Head. Combination Sanding head with: 6" Dia. contact roll (60 - 65 Duro) and 2-1/2" wide finishing platen; 25 HP motor; sanding head with: 37" x 75" abrasive belt with "POSI-TRAK" electronic tracking.Feed System: -- Variable feed speed 15 - 45 FPM; automatic conveyor belt tracking; 3-ply rough top conveyor belt. -- Anti-kickback fingers on infeed; air loaded sectional shoe with dial indicator adjustment; double grooved pinch roll on infeed of knife head. -- Infeed & outfeed pinch rolls on sanding head; air activated caliper disc brakes on all heads. -- Motorized part thickness adjustment of 0" - 6" with digital readout.Complete with: -- Controls mounted on belt loading side; main motor fuse protection on both heads; load meters for each head; "over thick" shutoff system; 24" infeed conveyor extension.

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included

TIMESAVERS - 2321-24-01: Wide Belt Sander with (2) Heads43" Width cap.; Drum, Combination Head.Head Configuration1st Head: 8" Dia. rubber covered contact roll, 65/70 Duro; 25 HP motor (4,000 RPM).2nd Head Combination head with: 5-1/2" Dia. rubber covered contact roll; 2-1/2" wide finishing platen; 20 HP motor (3,500 RPM).Specifications -- 43" x 75" Abrasive belts with: Dual "Posi-Trak" electronic solid-state tracking. -- Conveyor belt feed with: AC Inverter; variable feed from 15 - 45 FPM. -- Infeed & Outfeed: Spring loaded holddown shoes or rollers on all heads. -- Automatic part thickness set up; motorized thickness adjustment with digital indicator; 0" - 6" opening; infeed safety stop bar. -- (4) Jack screws for bed adjustment. -- Compressed air requirements: 4 CFM @ 90 PSI. -- Dust extraction requirements: 2,700 CFM. -- Electrical Requirements: 126 Full load amps @ 230 Volt.Equipped with & Features: -- Controls mounted on belt loading side. -- 14" Infeed conveyor area. -- Sanding head motors with: Air caliper disc brakes; motor load meters. -- Well-maintained and serviced.NOTE: Constant passline Sander 33" - 38".

TIMESAVERS 36" SPEEDSANDER WIDE BELT SANDER1-Head; 36" width cap.; combination sanding head with: 4" Dia. contact roll & 1-1/2" wide polishing platen; 7-1/2 HP, 1-phase motor. -- Abrasive belt size: 37" x 60" with: Electronic abrasive belt tracking; 4" max. thickness with: 34" - 38" pass line; rough-top conveyor with: 5 - 20 FPM variable feed via AC Frequency drive. -- Equipped with: Air activated emergency brake; outboard door interlock; infeed emergency stop bar; emergency stop buttons on outfeed. -- Includes: (1) 4" Dust outlet; ProScale digital readout; casters.

TIMESAVERS - 1311-13-1: Single-Head Wide Belt Sander1-Head; 37" cap.; 0 - 5" opening (33" - 38" pass line). -- Combination head with: 4-3/4" Contact roll & 2-1/2" finishing platen; 15 HP motor; 37" x 60" abrasive belt; disc brakes on main motor; centralized control panel. -- Features: Digital thickness readout; double infeed & outfeed holddown rollers; variable feed speed from 20 - 40 FPM; hour meter; main motor load meter/watt meter. -- Includes: Dial indicators on drums/platen; auto setup device; motorized lift; 13" infeed loading area; (4) bed jacks; quick release outboard support; through-beam abrasives belt tracking; infeed stop bar; UL listed controls.NOTE: Extra Sanding belts included.

Timesaver - Series 1300: Wide Belt Sander (3) Heads43" Width cap. drum; drum combination head.Specifications -- Dial indicators on drums/platens. -- 8" Drums. -- 5 1/2" Dia. on combination heads. -- 2-1/2" Width platen on combination head. -- 75" Abrasive belt length. -- 0 - 5" Opening (33 - 38" pass line).Equipped with & Features: -- Disc brakes on main motor. -- 20 - 45 FPM Feed speed A/C. --Auto set-up device. --Motorized lift. -- 14" Infeed loading area. -- Quick release outboard support. -- Through-beam abrasive belt tracking. -- 15" Minimum part length. -- Emergency stops at infeed and outfeed location.

TIMESAVERS - 2321-23-21, ...Planer Sander (2) Heads2-Head; 36" width cap.Specifications: -- 1st Head. 6" Dia. Helical head with: (6) Spirals of 4-sided carbide inserts; 25 HP motor. -- 2nd Head. Combination head with: 5-1/2" Dia. contact roll and 2-1/2" wide finishing platen; 20 HP motor; sanding head with 37" x 75" Abrasive belt with "POSI-TRAK" electronic tracking. -- Dial indicators for height adjustments. -- Conveyor belt feed with Variable feed speed 20 - 45 FPM; automatic conveyor belt tracking. -- Anti-kickback fingers on infeed; planer head with sectional infeed shoe and double hold-down rolls on outfeed; double infeed and outfeed rubber-covered hold-down rolls on the sanding head. -- Motorized part thickness adjustment: 0" - 5" With mechanical digital readout. -- Minimum part length: 15"; pass line height: 33"-38". Complete with: -- Controls mounted on belt loading side; air activated caliper disc brakes on all heads; load meters for each head; 14" infeed loading area. -- Dust extraction: 3,500 CFM; compressed air usage: 3 CFM @ 90 PSI. -- Total load amps at 230 Volts - 145 Amps.

TIMESAVERS - 352 HDA, ...Abrasive Planer/Sander2-Head, 51" width cap. Heavy Duty Sander. -- 1st Head: Smooth steel contact roll, 11-1/2" dia., 75 HP motor. -- 2nd Head: Spiral Grooved hard rubber contact roll (11-1/2" dia.) , 75 HP motor; 52" x 103" abrasive belts (6,300 & 4,300 SFPM) with POSI-TRAK electronic tracking. Equipped with: -- Heavy-Duty solid rubber (no vacuum holddown) feed belt for Heavy-Duty operation. -- Motorized part thickness adjustment, 0" - 6" opening. -- 38" - 32" Conveyor height passline with MITUTOYO LED readout, conveyor belt feed. -- 5 HP Variable feed speed from 20 - 60 FPM, smooth rubber conveyor belt. -- Infeed & outfeed spring loaded holddown shoes, infeed emergency stop bar, anti-kickback fingers on infeed. -- Disc brakes on sanding head motors, 18" infeed load area, and motor load meters on sanding heads.

TORIT - 460-IRD-20: Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Downflow air pattern allows airflow & gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure drop.Specifications -- 20 HP Direct drive; floor mounted blower. -- Fan inlet: 17". -- CFM: 7,000. -- Set of filter bags. -- Steel elbow from fan to collector. Motor Starter included.

TORIT 360-IRD-15 Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Down flow air pattern allows airflow and gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure dropSpecifications: -- 15 HP direct drive, floor mounted blower. -- 4,800 CFM @ 8" wg, 4,050 CFM @ 9" wg, 2,400 CFM @ 10" wg -- (21) Dura-life filter bags with a cloth area of 192 sq. ft. -- (3) Collection points for plastic collection bags.

TORIT-DONALDSON ADMC AD8 DRYFLO Cartridge Dust Collector. A Mist collector designed for long-lasting high collection efficiency capture of coolant and machining oil mists in metalworking applications. Even smaller amounts of dust can be filtered in the dirty air stream. -- DRYFLO is a proprietary cartridge which outperforms electrostatic precipitators and mist collectors utilizing standard HVAC envelope and cassette filters. Filter unit features a unique air-side filter retention system allowing for quick filter changes with minimal worker contact with collected oil. -- Also feature three-stage Filtration via a.) prefilter, b.) wrap allowing, c.) the filter cartridge to drain and coalesce smaller coolant mist droplets in to larger droplets. Plus optional fourth stage HEPA filters available for applications where smoke exists or additional efficiency of discharge air is required. -- Overall data: Capable of 17,600 CFM; (8) Filter Cartridges, 1,760 sq. ft. of filter area, -- Complete with: Ground mounted fan powered by a 40 HP motor, belt-driven. Fan includes a variable volume inlet. In prior application clean air was not retruned to building. -- Blower currently setup for approx. 15,000 CFM with 40 HP, Baldor Super-E, 324T frame, 1.780 RPM motor. -- Enclosure dimensions: 133" long, 68" deep, 160" high. Filter weight is 7,300 lbs.

TORIT - CHECKER BOARD: Control PanelTORIT Checkerboard Control Panel for a DFT3-18 Dust Collector up to a 25 HP Blower.Includes -- Start/Stop push control buttons for Dust Collection System. -- Electric disconnect to shut down power if needed. -- HEPA Filter pressure gauge. -- Alarm with light when dust filters need to be cleaned. -- Pressure gauge showing the air flow in the system. -- Air pressure pulse cleaning controls to clean dust from filters. -- Control box mounted on legs.

DONALDSON-TORIT - 376RFW-10 or 12: Dust Collector45,000 CFM @ 9.7:1 Air-to-cloth ratio; 140" dia. round baghouse with: (376) filter bags of 10' length (oval bags provide for radial movement of bag during cleaning for longer life), total 4,632 sq./ft. filter area. -- Filtration media cleaning via a floor mounted 7.5 HP medium pressure Air Pump (eliminates the need for compressed air, which can be susceptible to condensation and freezing); 36" x 65" return air outlet and 48" x 48" inlet for dust laden air. -- Includes: Rotating cleaning air manifold driven by 0.33 HP motor; (1) NEMA-9 solenoid and diaphragm valve which rotates over the bag openings; walk-in plenum for bag access/maintenance. -- Galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed; walk-in access door at top of ladder. -- Equipped with: Structural steel support; maintenance platform; caged ladder; bolt-on involute arm; explosion doors (need to be replaced). -- Includes Backward inclined FAN EQUIPMENT: Size 7 BCS floor-mounted Fan set at 45,000 CFM @ 15" SP belt driven at 1,485 RPM; powered by a 200 HP TEFC Motor via OMRON/IDM E7 Series Inverter. -- 24" Rotary Air Lock at the bottom of the 60° hopper. -- Complete with: Pictured electrical controls are included. -- NOTE: New 200 HP electrical motor was replaced recently. -- Unit had an accidental fire at bottom section near hopper causing the explosion doors to burst. Unit still working as they are not returning the air. Can be sold with or without replacement of doors; Cost of which is negotiable. -- Professional dismantling and rigging available at extra cost. Please call!