CANTEK - GOODSPEED CP-1250 AP Hydraulic Copy Lathe. -- General Data: 44" Length cap. with 4" min. length of stock and 1/2" - 4" max. diameter cap., hopper feed with automatic chucking, square or round stock can be hopper fed. -- Equipped with: 7.5 HP Spindle motor, 1,800 - 3,200 RPM spindle speed adjustable by pulley change, 3 HP hydraulic motor. -- Complete with: Swivel control panel, PLC sequence controller built into separate control cabinet, (3) pressure gauges, automatic way & support collar lubrication & safety wire mesh across the front of machine. -- Includes: Two hydraulic copiers (rough + fine). Travelling steady rest and installed knives. -- Production capacity: Approx. (5 - 7) pieces/Min for 600 mm length, (3 - 5) pcs./Min for 900 mm length, (2 - 3) pcs./Min for 1,200 mm length, depending on cutting speed, type of material, etc. -- Electrical load: 11.4 amps, 10.5 HP @ 575/3/60.volts.

CENTAURO T5-1600 Hydraulic Copy Lathe with (2) top plunging knives; Specifications: -- 63" (1,600 mm) Max. between centers, 4/5.5 HP main motor, two speed selector switch, 900 - 1,500 - 1,800 - 2,250 - 3,000 and 4,500 RPM spindle speeds. -- 1 HP Hydraulic power pack for variable speed carriage 0 - 19 FPM carriage; return speed 24 FPM, hydraulic tailstock with Pressure Reducing Valve (PRV) for fine control of pressure, especially helpful for small and/or slender turnings. Equipped with: -- (2) Independent copying units, (1) for roughing and (1) for finish cutting. 1st, 2nd pass & auto feature with 2nd pass active it will cut the pattern 2 times automatically and sequence the tools between cuts. -- Revolving steady rest, max. dia. 140/100 mm square ( 5.5"/3.9"), and for max. dia. 90/65 mm max. square billet size. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. Includes: -- (2) rear-top plunging slides manually operated with knives for making dowel ends; 45/26 mm drive center for headstock and 12 mm center for tailstock, (2) V-type gouges with 0.6 & 3.5 mm cut radii.Features: Centauro AG-125 Knife Sharpener.NOTE: Ex-Factory handles import/export to just about any country in the world.

CENTAURO TC-1200 Copy Lathe;47-1/4" Max. between centers. -- 4-3/4" Height of centers over bed. -- Max. copy dia. 6" (4-1/8"). -- Max. dia. permitted by traveling steady 3-1/2" (2-1/2"). -- 4 HP main motor, 900 - 1,500 - 2,200 & 3,540 RPM spindle speeds. -- 1 HP hydraulic variable speed carriage with tool post and revolving steady rest. -- (2) Independent gouges working in conjunction with the traveling steady rest. -- Variable speed hydraulic saddle movement. Standard Equipment & Specs: -- Drive center with (2) interchangeable heads 1" and 1-3/4". -- Tailstock revolving center 1/2". -- Traveling steady rest max. 3-1/2" (square 2-1/2" x 2-1/2") with reduction bushing. -- (2) Vertical Tantung gouges, radius 1.2 mm and (1) precutting tool. -- Work-piece centering device. -- Tool support rest for hand turning. -- (2) Dust extraction ports 4" dia. -- Motor protection switch. -- Emergency push button. -- Front sliding safety guard. -- Standard: Service tool kit and Abrasive stone for cutting edge dressing.

ELIO VALERI ELVAP 120 Copy Lathe. -- General data: 48" max. length cap., 7" max. dia. without steady rest, 3.93" max. dia. with steady rest, and up to 2.5" x 2.5" dia. with steady rest for square pieces; 0 - 39 FPM forward and 0 - 52 FPM return speed, 5.5 HP motor, 1,300 - 3,500 - 5,000 RPM; -- Features: Air/oil feed and copier, chain head stock drive, gate loading, pattern; pneumatic tail stock, automatic pneumatic control program.

FRAMA - TC-1500: Hydraulic Copy Lathe with (1) V-Gouge Copy Head & (2) Manual Top Turret Heads & Knife SharpenerHydraulic Copy Lathe with: (3) Different speeds during execution of the work.Possibility of manual or automatic configuration on (3) intensities: (1) Regular working speed; (2) Slow working speed for difficult points reproduction; (3) Fast speed to eliminate nonproductive points. Technical Data -- Main drive motor: 6 HP. -- Hydraulic pumping unit: 2 HP Motor. -- Max. turning dia.: 300 mm (12"). -- Distance between center: 1,500 mm (59"). -- Max. cross-slide speed: 9.5 MPM (30 FPM). -- Carriage return speed: 11 MPM (36 FPM). -- Copying device stroke 75 mm (3"). -- Max. hydraulic pressure between cones: 20 kG/CBM. -- Headstock taper: MT 4. -- (8) Turning speeds: 1,000 - 1,250 - 1,750 - 2,000 - 2,250 - 2,500 - 3,500 - 4,500 RPM. Also included: -- FRAMA - ATC 2005: Knife Grinder. 2 HP Motor. -- (1) Steady rest - 70 mm; (1) 18 mm; (1) adjustable for square. -- Tailstock & Tool Holder.

INTOREX TXA-1200 Automatic Hydraulic Copy Lathe;Specifications: -- 1,200 mm (47-1/4") Max. turning length, 210 mm (8-1/4") max. turning diameter. -- Max. turning dia. with standard steady 90 mm (3.5"). -- (2) Hydraulic copiers. -- Max. size of square stock for turning with automatic feed 100 mm (3.9"). -- (3) Tool holder turrets. Hopper feed unit. -- (8) Head speeds in a range from 750 - 5,500 RPM. -- 6 HP or 7.5 HP Headstock spindle motor. -- 4 HP Hydraulic pump motor.

LA NUOVA SCOLPITRICE 201-16 Multi-Spindle Carving Machine.(16) Cutter Stations, 55" max. workpiece length,Specifications: -- (16) Dual carving spindle heads, 8" between spindles, 20" max. working diameter. -- Each head has a roughing & finishing spindle, all heads swivel 360° with pneumatic locking. -- Upper carriage controlled by (2) High Frequency changers allowing (2) motor speeds of 12,000 & 18,000 RPM. -- Pneumatic chucking of material, stock turns 360°. Copy stylus of hardened and ground steel, adjustable for depth on either side. -- Traverse feed of carving heads was patented and requires no maintenance. -- Includes: Lot of tooling. Table for flat/horizontal copying.Note: Machine completely gone over and all heads rebuilt in 2011 and used sparingly since.Actual model is 201-16.

LOCATELLI "OMK-300" Automatic Lathe with Sanding; From automatic feeding to finished product ejection - a complete "Turning & Sanding" System. -- 11-13/16" Max. between centers, 3-1/8" max. & 5/16" min. stock dia., 5.5 HP spindle motor with (3) spindle rotations of 3,020 - 4,580 & 6,400 RPM.6-Station Rotary Carousel/Drum with the following operations: -- Station 1: Pickup and centering of workpiece. -- Station 2: Turning with hydraulically operated roughing & finishing gouge. -- Station 3: Finish turning with hydraulically operated finishing gouge; rough & finish gouges advance via 1.5 HP hydraulic motor at a rate of 0.33 - 52 FPM. -- Station 4: Initial sanding with adjustable 0.5 HP vibrating brush. -- Station 5: Secondary sanding with adjustable 0.5 HP vibrating brush. -- Station 6: Ejection of finished workpiece. -- PLC Function for immediate fault detection and facilitates setup. Complies with CE high standards for operator safety. -- Features: Billet capacity has been increased to a special 5.9" x 5.9" (150 mm square). -- Complete with: Separate operator control panel. -- Includes: Inventory of spare parts and tooling. -- Machine kept under power but has not been used for production for several years.

MATTISON 69-42 MATTI-MAX Heavy Duty Automatic Rotary, high production Turning Lathe.Microprocessor controlled for quality turnings and ease of setup; 42" long turning cap. with rotating rear arbor, 4" x 4" max. and 3/4" x 3/4" min. stock size. -- Drives & Speeds: Equipped with: 20 HP - 2,700 RPM Cutterhead Drive, 2-5/8" dia. arbor with variable speed, 2 - 45 RPM stock-rotational speed via 1.5 HP DC drive (reversing) & self-contained hydraulic unit for precise feed control.. -- Complete With: Automatic hopper feed; MATTI-MAX microprocessor-based PLC controller with keypad entry; machine functions & operations parameters are set directly from the control; RPM of workpiece and feed rate can be programmed to vary during the cut. Matching the feed rate to the stock-rotational speed produces an efficient cut -- Features: MATTI-MAX also allows rough cutting at higher speeds (especially rounding of corners) and fine finish cutting at slower speeds. . Pneumatic tailstock with dual pressure to insure penetration of spur center at high pressure and can be adjusted lower for small dia. turnings. -- Total electrical load 27 Amps.

MATTISON - 69- 54: Automatic Lathe -- 54" Length capacity with working dimensions: 4" x 4" Max. x 3/4" x 3/4" min. -- Hopper feed with: Automatic chucking and pop-up. -- Spindle drive: 25 HP Motor; spindle dia.: 2-5/8"; arbor speed: 2,700 RPM. -- Feed rates: 2 - 45 RPM; Variable feed speed and double-end drive.NOTE: Lot of additional knives & heads available at additional cost.

MATTISON - 69-42 MATTI-MAX: Heavy-Duty Automatic Rotary, high production Turning Lathe with Hopper FeedMicroprocessor controlled for quality turnings and ease of setup; 42" long turning cap. with rotating rear arbor; 4" x 4" max. and 3/4" x 3/4" min. stock size. -- Drives & Speeds: Equipped with: 25 HP - 2,700 RPM Cutterhead Drive; 2-5/8" dia. arbor with variable speed. -- 2 - 45 RPM Stock rotational speed with: 1.5 HP DC Drive (reversing) & self-contained hydraulic unit for precise feed control.Complete with: -- Automatic hopper feed; MATTI-MAX microprocessor-based PLC Controller with keypad entry; machine functions & operation parameters are set directly from the control; RPM of workpiece & feed rate can be programmed to vary during the cut.Matching the feed rate to the stock rotational speed produces an efficient cut.Features -- MATTI-MAX Allows rough cutting at higher speeds (especially rounding of corners) and fine finish cutting at slower speeds. -- Pneumatic tailstock with: Dual pressure to ensure penetration of spur center at high pressure and can be adjusted lower for small dia. turnings. -- Total electrical load: 26.5 HP. -- Setup Stand.NOTE: Large quantity of knife & heads available for additional cost.

MINNESOTA 24-8 Multi-Spindle Carving Machine.Specifications: -- Spindles/Capacity: (24) Spindles, 8" between centers & 72" length capacity. -- Motors: (12) 0.75 HP motors with (1) motor driving (2) spindles via flat belt. -- Features: Manual table elevation, motorized stock rotation, non-indexable head. -- Comes with: (2) Sets of carving tools (one medium and one fine). -- Includes: Tables for flat carving - to be confirmed (?).

TERCO NORTHSTAR 10-8 Spindle Carver.8-Spindle Carver with 10" center-to-center chuck spacing. -- (2) 0.5 HP - 3,450 RPM spindle motor direct "belt drives" spindles for 11,000 RPM rotation. -- 36" Long carving cap, with optional length extensions up to 72". -- Manual rotation for round parts. -- Operator manually traces the pattern details of the master with copying stylus. -- Capable of doing both base relief (flat backed) and 360° full round carving. -- Includes: (1) Set roughing bits, (2) sets finishing bits, tools, and manual.

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

ZUCKERMANN CHALLEGER Copy Lathe w/Sander for asymmetric/irregular shaped parts.Hopper feed, single spindle; approx. 149" (3,800 mm) max. between centers, 8-13/16" (250 mm) max. part dia.; 5 HP cutter head motor at 6,000 RPM, oscillating belt sanding unit, both units work together. -- 'Cup' style Cutter head; 2 HP spindle & pattern rotation motor; mechanical & pneumatic traverse of cutter head and sanding carriage. -- Complete with: Built-in operator push button control panel and overhead dust collector hood.

ZUCKERMANN OPTIMA-S-8/1000 Copy Lathe with integral sanding.For asymmetrical or symmetrical wood turnings ranging from furniture legs (Queen Anne), gunstocks, guitar necks, to tool handles and the like. -- General Specs: 8-Spindle Copy Lathe, 39.3" (1000 mm) max. copying length, max. working dia. 200 mm (7.86"); 5.5 HP motor on each spindle, 6,000 RPM belt-driven spindle with cup cutters. All cutters are copying according to one sample specimen. -- Equipped with: (8) Single head sanders for simultaneously shaping & sanding; (2) 2.8 HP motors power all sanding heads, 6" wide sanding belts. -- Speeds: Stock rotation variable from 15 - 75 RPM, variable feed speed of shaping & sanding cycle from 200 mm/Min - to 1,200 mm/Min (0.75 IPM to 47 IPM), pneumatic clamping of workpiece. Includes: Installed used cup cutter heads. -- Larger working dia. is possible by omitting adjacent workpieces and as the copier allows. -- Actual model is OPTIMA-S-8/1000. -- Machines are connected and can be viewed in operation. --NOTE: Several machines of the same model are available at the same location.

ZUCKERMANN CHALLENGER 1700 37-Z SYNCHRO Copy Lathe. Single spindle hopper feed CNC Copy Lathe for shaping & sanding asymmetrical parts. -- Size Capacity: 67" Maximum 67" (1700mm) and 4" (100mm) minimum working length, 9.8" maximum working diameter. -- Drives/Speeds: The cutter head is belt driven by 5.5 HP motor to run at 6,000 RPM, sanding motor 1.5 HP to drive a 5-7/8" wide sanding belt. Work piece rotation CNC controlled for variable rate from 12 - 130 RPM, via 4 HP motor, carriage speed CNC controlled 7- 67 inches per minute, automatic hopper feed as well as automatic unloading . -- Controls: Machine sequencing, cutting and sanding speeds controlled by SIEMENS "Sinumerik 810 T" CNC controller with programmable memory for rapid set up. --Complete with: Various spare parts & 220 or 440 V operation transformer.

--In Auction: https://exfactoryauctions.com/Detail/LC-230120/event/A122024$1--NO RESERVE!-- --SUPER RARE MACHINE-- BACCI T4M-O 4-Spindle Asymmetric Copy Lathe, with Sanding & Enclosure Specifications: Distance between spindle centers 170 mm (6.69"). Max. working height 165 mm (6.50"), Max. copying length 1000 mm (39.37"). Standard cutter dia. 35 mm (1.38"). Cutter holder dia. 145 mm (5.71"). Cutter holder speed 5,300 RPM. Spindle speeds 25 & 42 RPM. Carriage speeds 75 - 200 mm/Min. (2.95 to 7.87 IPM). Equipped with: (4) Duplicating/carving/copy spindles. Complete with: (4) 130 mm (5.12") W Copy Belt Sanders for asymmetrical parts, with 130 x 990 mm (5.12" x 38.98") Belts. 114" x 92" x 88" H Enclosure. NOTE: Larger diameters possible by using every second carriage position, ie. (2) heads instead of (4) heads. Machine weight: 3,330 Lbs. Enclosure weight: 775 Lbs.

BACCI T4M-O 4-Spindle Asymmetric Copy Lathe, with SandingSpecifications: -- Distance between spindle centers 170 mm (6.69"). -- Max. working height 165 mm (6.50"), Max. copying length 1000 mm (39.37"). -- Standard cutter dia. 35 mm (1.38"). -- Cutter holder dia. 145 mm (5.71"). -- Cutter holder speed 5,300 RPM. -- Spindle speeds 25 & 42 RPM. -- Carriage speeds 75 - 200 mm/Min. (2.95 to 7.87 IPM).Equipped with: -- (4) Duplicating/carving/copy spindles.Complete with: -- (4) 130 mm (5.12") W Copy Belt Sanders for asymmetrical parts, with 130 x 990 mm (5.12" x 38.98") Belts. -- 114" x 92" x 88" H Enclosure.NOTE: Larger diameters possible by using every second carriage position, ie. (2) heads instead of (4) heads.Machine weight: 3,330 Lbs.Enclosure weight: 775 Lbs.

CALPE TH5-1600 Heavy-Duty High-Production, Fully Automatic CNC Lathe: General Description: -- Multi-Spindle cutting simultaneously, (5) spindles using V-type gouge knives. -- 63" (1,600 mm) Max. distance between centers; 5-1/2" (140 mm) max. swing diameter between spindles. -- CNC Controlled with 2.95" (75 mm) travel for depth of cut. Motors/Speeds: -- Servo controlled CNC drives: -- CNC controlled electronic variable speed head drives the movement of the (5) gouge tools. -- CNC controlled feed speed carriage, variable up to 50 FPM (15 MPM). -- (1) Head stock variable speed drive for the (5) spindles, up to 6,000 RPM, approx 10 HP. -- Fast return travel of up to 590 IPM (15,000 mm/Min). 2 HP approx hydraulic drive -- Loading device & tail stock powered by hydraulic pump with 2 HP - 1,750 RPM motor; No. 5 Morse taper on main spindle shaft. Features: -- Automatic loading & unloading device; carriage mounted with linear guides providing high precision movement. -- Full CNC controller with on-screen CAD programming for all products.Matching CALPE L6-1600, record number LC-010996 spindle sander is available at additional cost at same facility.