15" Width cap. with 1/4" - 8" thickness opening, 1/16" max. depth of cut; 3 HP single-phase motor belt drives 3-knife, 3-15/64" dia. cutter-head at 5,000 RPM; head with high-speed steel knives, max. thickness 8", min. 3/16"; dual feed speed of either 16 or 30 FPM; 16" x 42" cast iron table, table extensions on infeed/outfeed. Complete with: Magnetic controls, 2" dia. metal infeed & outfeed rollers, open fabricated steel base, and large hand wheel for cutter-head assembly adjustment.

GRIZZLY G4185 2-Spindle Horizontal Boring Machine, Will Accept 3-Spindle Boring HeadSpecifications: -- Max. stock width 7-1/2";. -- Table size 9-3/4"; x 15-3/4";, Max. table height 35";, Table height adjustment 3-1/2";. -- Max. bit cap. 9/16"; (Right-hand threaded), Spindle travel adjustment 3";, Spindle speed 4,000 RPM, Max. speed 12 SPM at 90 PSI. -- Hold-down force 600 Lbs.Equipped with: -- 2 HP 3,450 RPM TEFC Direct drive motor. -- Pneumatic spindle travel. -- 2-1/4"; Pneumatic hold-down. -- Pneumatic foot pedal control. -- Steel stand.Complete with: -- GRIZZLY "G5952"; 2C-W19"; 2-Spindle Boring Head, Max. bit cap. 5/8";, Bit threads 7/16 - 14 TPI Right-hand, Spindle speed 4,000 RPM.

GRIZZLY G9981 Heavy-Duty Overarm Pin Router Specifications: Throat 25-19/32". Table size 29-3/4” LR x 21-1/2” FB with Table tilt 0° - 45° Forward, Table height 36-1/2" - 42-3/4".Vertical table travel 8". Spindle speeds 10,000 & 20,000 RPM. Spindle travel 3-15/16". Equipped with: 5 HP - 3,450 RPM Motor. Foot pedal control.

GRIZZLY G0631 Downdraft Sanding Table28" x 79" Table area with a 1 hp motor using a squirrel cage fan pulling up to 1,437 CFM, to pull the dust away while sanding on Non-maring rubber grommets to suport your work. -- Table surface area 25 1/4" X 76 1/4", table height 31 1/2" -- 1 st stage filter 16" X 25" X 1"; 2nd stage filter 16" X 25" X 2" -- Filter micron: 1/0.3 -- Inlet size 8" Features; -- SHeet metal table construction, -- Easy access filter bay, quiet operation 68 Db, -- Two convenient dust drawers -- Table surface 39-1/2"x 28". -- Filter size 16"x 25"x 2" cleaning down to 0.5 micron. -- Working height of 37".

GS - HEAVY-DUTY 34 KVA, ...Transformer.SCR Drive Transformer. -- Cat # DT631H34S. -- High voltage 575 Volts Delta; Low voltage 230 Y/133.

GUBISCH MODEL CP-230 4 HEAD PUSH FEED MOULDER: -- 4-Head (T-R-L-B), working capacity 6" x 4". -- Head sequence: Top 15 HP, right/left 15 HP and bottom 15 HP motor. -- Spindle dia. 1-13/16" all heads with cutterhead speed of 6,000 RPM on vertical spindles and 7,000 RPM on horizontal spindles. Heavy duty, built-in profile jointers on spindles #2, #3 and #4. -- Mechanical adjustment for spindle settings. Spindle adjustments from the front side of machine. -- Variable speed feed drive via 7-1/2 HP, variable speed motor with speeds from 16 to 120 FPM; with (2) powered rollers from the top and (2) powered rolls in the table. -- Infeed table;chromed table plates. --Pneumatic jointers on all 4 heads Amazingly well built Moulder; off-the-shelf parts accessibility; low maintenance/operating costs.

GUIDETTI - WIRE 415, ...Copper & Wire Chopper with Pre-Shredder -- Currently Disassembled.Specifications: -- Feed size of material; 1,310 x 2,140 mm. -- Load pusher stroke: 600 mm. -- Rotor diameter: 220 mm. -- Rotor rotation speed: 82 RPM. -- Hydraulic power: 0.75 kW. -- Grid hole diameter: 40 mm. -- Rotating blades: 23 + 4 External. -- Low hours; 2,300 Hrs.? -- Has not been used since 2015GUIDETTI Pre-Shredder New in 2012. -- Model: PM6N 600/200 -- Low hours: 1,700 -- Has not been used since 2015 -- Loaded onto your truck.

HAAS - 2000XL 2.0, ...Mobile ShredderLow Hours; 2018 YMFG.Specifications & Features: -- Can be used at any location (comfortable transport measurements). -- Easy & quick positioning thanks to crawler track and radio remote control. -- Shreds different materials with just (1) tool configuration. -- High throughput capacity of up to 100 tons/Hr. -- Resistant against foreign bodies. -- Low wear cost and long lifetime. -- Service and maintenance friendly. -- No wrappings; self-cleaning. -- Quiet main drive.

RAFIX - Futura 250: Hinge Boring & Inserting Machine with 1-1/2 HP MotorSpecifications -- High-quality air cylinder (80 mm bore with 650 ft. Lbs of pressure @ 90 PSI) rated for 3-1/2 million 3" strokes.A skilled Operator can bore & insert in (3 - 4) seconds. -- Features: (2) Types of boring depth adjustment: Drawbar style for quick and easy adjustment and a solid stop adjustment for the changing of door thickness applications. This allows changing of the door thickness and still bore the same depth without adjustment. -- Fixed table with: Adjustable back rail to control the tab location. -- Enclosed cutting area for better chip removal with blow off nozzle to assist in chip evacuation and adjustable 2" & 4" vacuum hookup. -- Pneumatic drilling unit with push button control. -- Includes: Adjustable cutting speed control; indicator light; reset thermal circuit breaker; emergency stop button; drill & insert buttons (2-hand activation for Operator safety); rotary switch for pair of pneumatic holddown clamps; 600 mm ruler & (4) flip stops.

HAMMEL 750D HAMMERMILL NEW IN 2019Approx 3,000 Hours --Hydraulic recycling machine with 2 slow running tool shafts --Suitable for Wood (Old wood, construction & demolition wood, rhizomes, green waste, pallets, cable drums) or Rubbish (Domestic waste, industrial and commercial waste) and Paper, paper rolls, aluminum profiles and balesAdvantages: --Increased performance for more throughput --low energy consumption --Very easy to maintain --User-friendly handling by IFM control --Better accessibility of the control panels --Low noise --Tilt funnel with increased inclination for optimum material flow --Mobile on a chain or semi-mobile on a hooklift

HAMMOND DK-1055-B Cyclone Dust Collector w/ After-FilterSelf-contained indoor cyclone type unit w/afterfilter bags, the blower wheel is located on the clean air side and is direct driven by 7.5 HP motor @ 3,600 RPM, performance ranges 3,470 CFM @ 5" H20, 2,727 CFM @ 8.6" H20, 2,200 CFM @ 11.4" H20. -- (1) 10" Dia. inlet and (1) 8.5" x 15" outlet; waste discharges via bottom of unit to (2) 55-gal. drums (drums not included). -- Includes: Multi-exhaust manifold with (4) after-filter bags, 167 sq. ft. cloth area, push button starter.

SPX FLOW HANKISON HPRN200 200 CFM Non-Cycling Refrigerated Compressed Air DryerSpecifications: -- Cap. 200 SCFM at 100 PSIG & 100° F. -- Max. working pressure 232 PSI. -- Max. inlet temperature 120° F -- Refrigerant type R-407C.Equipped with: -- 200 W (1/4 HP) Refrigeration compressor motor. -- Stainless steel cross flow heat exchanger. -- LED Dew point indicator. -- Dry alarm contact. -- Timed electronic drain valve.

SPX FLOW HANKISON HPRN200 200 CFM Non-Cycling Refrigerated Compressed Air Dryer Specifications: Cap. 200 SCFM at 100 PSIG & 100° F. Max. working pressure 232 PSI. Max. inlet temperature 120° F Refrigerant type R-407C. Equipped with: 200 W (1/4 HP) Refrigeration compressor motor. Stainless steel cross flow heat exchanger. LED Dew point indicator. Dry alarm contact. Timed electronic drain valve. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

IMA NOVIMAT COMPACT/I/G80/700/L12 EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): -- Basic Specifications:Edgebanding coil stock capacity, 0.3 - 3 mm; (0.012 - 0.118"), Strips up to 12mm (0.47") can be processed. Panel thickness min/max 8 - 60 mm (0.315 - 2.362").Equipped With: -- Spraying Unit, anti sticking solvent, top and Bottom application. -- In-feed Fence with N.C. servo motor positioning. -- Pre-Milling Unit 08.378, with kW 4.5 x 2 (HP 6 x 2) vertical joining spindles, N.C. controlled, both w/jump movement and reversible rotation, SIKO digital readouts, particle & debris air jet blower. -- Edge Pre-heating Lamps, for best possible glue bond. -- Glue System: EVA Glue (Hot Melt) + 1 Quick Melt unit. -- Side Pressure Section: N.C. controlled, with (5) pressure rollers w/individual pneumatic pressure control for each roll -- Edge Magazine: Vertical coil cartridge assembly, 1 x 6 positions with auto edge-selection and HD guillotine.Workstations: -- End Trimming Unit 08.0555: High speed, double motor KW 0.66 x 2 (HP 0.88 x 2) suspended from the hold-down beam, automatic chamfer adjustment 0° - 15° for speeds up to 32 m/min (105 ft./min). -- Flush/Bevel/Radius Trimming Unit: Top & bottom, multi profile, N.C. controlled, KW 1.5 x 2 (HP 2.0 x 2) - 12,000 RPM motors, bevels 0°-30°, vertical & horizontal tracing wheels, digital read-outs. -- Corner Rounding Unit KFA 25: High Speed, (1) x Kw 0.66 (HP 0.88), 12000 RPM motor with multi-profile and N.C. servo positioning. -- Profile Edge Scraping Unit: Top & bottom, multi-profile (4) positions N.C. controlled scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing wheels, digital readouts for adjustments, chip extraction system for scraping unit. -- Glue Scraping Unit: Flat, top & bottom self-tracing glue scraper, N.C. controlled. -- Buffing Unit: Double Stage, (2) top & (2) bottom KW 0.18 x 4 (HP 0.25 x 4) - 3,000 RPM ea. motor for linear & vertical corner edge polishing. -- Glue Scraping Unit: Flat, top & bottom self-tracing glue scraper. -- Buffing Unit: Top/Bottom (2) x KW 0.18 (HP 0.25) - 3,000 RPM ea. motor.Operator Interface: -- ICOS OPEN, Large color LCD display; displays stored data, on/off work station sequence, troubleshooting diagnostic; data input by alphanumeric keyboard. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete With: -- Heavy Duty "sliding" feed chain with 80 mm wide x 60 mm long rubber pad inserts, central lubrication of transport chain, -- Variable Feed Speed 6 - 30 MPM (20 - 98 FPM); -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Frequency inverters; ball bearing guided outboard panel support up to 27-1/2", sound enclosure, all stations, all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Unit with polishing solvent prior

IMA ADVANTAGE 500 L EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Production Edgebander -- Specifications:Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped With:Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. -- Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is IMA ADVANTAGE 500 L

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMA - HKA EXPERT CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. Designed for straight or curved (contour) edgebanding:0.5 - 3 mm Edgebanding thickness; 16 - 45 mm (0.63" - 1.77") panel & banding height; 23 - 45 mm (0.9" - 1.77") min. strip width; 100 mm (3.9") min. panel width; 250 mm (9.8") min. strip length. -- Equipped with: Versatile glue head that can be fixed to 1-side of the table to allow the operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine, via foot-pedal control. -- Work Table:32" (800 mm) Dia. coil dispensing table, large 813 x 914 mm (32" x 36") High-Flow Phenolic worktable surface;Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head (hot melt) glue pot" with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.