EXTREMA DC-240.3 TYPHOON Fabric Filtration Dust Collection System. Powerful, portable, and affordable dust collector with roll around casters mounted to a steel platform base.Specifications: -- (2) Oversized Fabric filter top bags, approx. 75 sq. ft.filter area, are placed above plastic collection bags, approx. 18.85 cu. ft. storage capacity. -- 3,950 CFM Output with single-stage blower. -- 5 HP Induction motor. -- Filter bags filter dust particles down to (5) Micron in size. -- Main inlet 10" or dual 4" adapter. Also available in Single Phase.

EXTREMA DC-232.3460 TYPHOON Fabric Filtration Dust Collection System. -- Powerful, portable, and affordable dust collector with roll around casters mounted to a steel platform base. -- (2) Oversized Fabric filter top bags are placed above fabric collection bags. -- 2,950 CFM Output with single-stage blower. -- 3 HP Induction motor. -- Filter bags filter dust particles down to (2) Micron in size. -- Quad 4" dust port adapter.

EXTREMA DB-50.3 TYPHOON BLOWER. Capacity 5 HP, 3,200 CFM. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller, 10" inlet, 13" impeller, 12" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. - Complete with magnetic starter. -- Note: 460 Volt available

EXTREMA DB-75 TYPHOON BLOWER. Capacity 7.5 HP motor and rated at 4,700 CFM. -- Solid heavy gauge steel construction. -- Heavy duty 13.5" dia. dynamically balanced steel impeller. -- 12" Inlet, 13.5" impeller, 14" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. -- Complete with magnetic starter. -- Note: 460 Volt available

EXTREMA - DCY-1220 L3 TYPHOON: Cyclone Filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system before passing finer particles through the fan and filter. -- Air volume rated @ 8,800 CFM. -- Unit includes: 20 HP Motor with a Soft Start already wired in. -- Rotary air lock with: 1 HP Motor @ 38 CFM. -- Low noise operation. -- Standard support frame: LEG 3; 164" clear height x 149" clear width x 91" clear depth. Includes after filter Baghouse DC-327E. Features: 16" Inlet; (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) micron filter. -- Unit is enclosed.

EXTREMA DC-4100 Baghouse Dust CollectorThe "DC-4100" baghouse dust collector is designed to achieve maximum airflow with a superior filtration area. This is achieved by using (36) smaller diameter filter bags to have more filter media in the same space as other similar dust collectors of its size. More filter area means better airflow with less filter maintenance. A manual bag shaker is included.The DC-4100 meets the NFPA664 CFM requirements for indoor dust collectors. The compact design allows this maximum filtration unit to use a depth of less than three and one half along a wall. The 10HP main motor has a dynamic balanced impellor and a magnetic starter is included.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 361 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (36) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 12".

EXTREMA DC-3075.1 TYPHOON Fabric Filtration Modular Dust Collection System.With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive. -- (3) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 4,550 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 7.5 HP motor with push button control and motor starter. -- 13.5" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy installation and removal of bags. -- Filter bags filter out dust particles down to (1) Micron in size; 6 mil thick plastic bottom collection bags are standard. -- Options: Remote control and drum storage kit.

EXTREMA DC-275.3 TYPHOON Cyclone & Fabric Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags. -- Air volume output rated @ 4,850 CFM. -- 7.5 HP Induction motor. -- 14-3/4" Steel blower fan impeller and is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter dust particles down to (1) Micron in size. -- Low noise operation. -- Includes: Sturdy steel tripod cyclone mounting stand and drum dolly. (drum not included).

EXTREMA DCF-327E Baghouse Dust Collector.Features a 16" inlet; unit has (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) Micron filter. -- Available for outdoor & indoor use; unit is enclosed. -- Excellent addition to the "DCY Typhoon" Dust Collector; ...ask us why!

EXTREMA DC-3150S TYPHOON Fabric Filtration Dust Collection System.With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive. -- (4) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 7,500 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 15 HP induction motor. -- 25" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy addition or removal of plastic bags. -- 1-Micron filter bags with 6 mil plastic bottom collection bags are standard. -- Wye-Delta soft start power switch. -- Options: Remote control, drum storage kit.

EXTREMA RC-10 Air Lock Standard capacity Rotary Air Lock; Cycles waste off of a cyclone dust collector, while maintaining internal pressure. -- The Rotary Air Lock is an essential device for dust collectors that dump directly into a dumpster or hopper. -- This unit has a 16" dia. 1 HP - 33 RPM TEFC Direct drive motor -- 16" inlet dia. & 16" outlet dia. -- (8) rubber blades. -- Does not include electrical controls. -- Features: 38 Cu. ft./min. cap.

EXTREMA DB-250 TYPHOON BLOWER. Capacity 25 HP, 10,350 CFM.Specifications: -- Inlet 18", 27" impeller, 20" outlet. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. -- Complete with magnetic starter. Note: 460 Volt available

EXTREMA DC-232.3 TYPHOON Fabric Filtration Dust Collection System. -- Powerful, portable, and affordable dust collector with roll around casters mounted to a steel platform base. -- (2) Oversized Fabric filter top bags are placed above fabric collection bags. -- 2,950 CFM Output with single-stage blower. -- 3 HP Induction motor. -- Filter bags filter dust particles down to (2) Micron in size. -- Quad 4" dust port adapter.

HOLZ-HER DYNESTIC 7516 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications: 5' x 10' MATRIX Table for "Nested Base" Manufacturing. -- Working Field: "X" Axis 122.2" (3,105 mm), "Y" axis 61.45" (1,561 mm), "Z" axis stroke is 16.5" (418 mm). -- Positioning speed: "X" & "Y" Axis 230 FPM (70 MPM), "Z" axis is 65 FPM (20 MPM). -- Worktable: Flat table designed for "Nested Base Manufacturing" with (4) pneumatically controlled reference stop pins. -- Boring Unit:2 HP (1.7 kW) motor for spindle speed from 1,000 to 4,400 RPM;(10) Independent vertical boring spindles with (6) spindles in the "X" axis & (4) spindles in the "Y" axis; -- Machining: (1) 15 HP (11 kW) Electro-spindle Router, HSK F63 adaptor, 1,000 - 24,000 RPM;(1) 8-Position ATC. (dynamic carrousel type) -- Operator & Machine Control: PC Front-End with: CAMPUS Version 6.3.0.3 (BECKHOFF CNC Version 2.3.7) machine control,17" Color Flat Panel Monitor; continuous graphical and barcode interface, (3) axes simultaneous control; feed rate and spindle speed override & axis movement. -- CAMPUS/NC Hops Software: This package provides the prerequisites for effective machining and convenient operation. Our ECO Mode automatic standby control is a standard feature on all HOLZ-HER CNC machining centers for software-controlled minimization of the power consumption.Campus aCADemy is a full-fledged, high-performance CAD/CAM software package with versatile import features. -- Complete With:(1) BECKER 250 m³/Hr vacuum pump; manual central lubrication pump for guides & ball screw; left & right-side safety enclosure; Hand Control, pendant for set-up and program try-outs -- Actual Model is HOLZ-HER DYNESTIC 7516 10.5.

HOLZ-HER - 1516, ...Case Clamp (Single-Bay) -- Specifications:1-Bay Clamp, 100" x 50" x 24" clamping cap.; (1) movable, vertically positioned clamping beam with (3) horizontal clamps, (4) adjustable vertical clamps. -- Total of (14) pressure cylinders with 3-7/8" stroke & (4) adjustable counter-pressure bars; 700 Lbs/cylinder pressure at 100 PSI compressed air; built-in controls with pressure gauge.

HOLZ-HER 1329 SPRINT PREMIUM EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) & Features the HOLZ-HER Patented Dual "GLU-JET" EVA & PUR Zero Joint Technology System; Specifications: -- Edgebanding Capacity: edge thickness min./max. 0.4 - 15 mm (0.016 - 0.59"), coiled material 0.4 - 3 mm (0.016 - 0.157"); Panel thickness 8 - 60 mm (0.236 - 2.362"), workpiece width min. of 60 mm (2.36"); workpiece length min. 160 mm (6.29"); Feed speed 10 - 18 MPM (33 - 59 FPM). -- Programmable Logic Control (PLC) for Pre-Milling, edge feed, glue application, end trimming, flush trimming, radius trimming, scraping, corner rounding, and buffing. -- Holz-Her PPC 315 "EDGE CONTROL TOUCH" Electronically controlled set-up processes with 100% repetition accuracy. 18.5" Flat Touch Screen with Brilliant graphic display of machining process. Simple operation – rotating and swiveling control panel at eye height.,Programs can be easily created and recalled at will; Graphic interface makes programming easy,Icon of each unit may be brought up on the screen to show the operator the status of the unit and the parameters which can be programmed;Edgebander can be operated manually when required, without necessity to write a program.Machine In-Feed Configuration: -- Pre-Milling Station : (2) 2.0 KW (2.68 HP) - 12,000 RPM motors; Equipped with "ProLock" quick-change flange including height adjustment for optimum utilization of cutters. -- Edge Feeder Magazine: "SYNCRO" drive. The new magazine with its synchronous adaptation to the feed rate guarantees short intervals between work pieces & simultaneously optimizes edging protrusions. Small 3° feed angle thanks to nozzle design with easy feeding of coils, strips &up to 3 mm & solid wood edging up to 15 mm (.059"). Exclusive "Tractor-Belt feed System", edge guide equipped with automatic guillotine lock-out for safety, -- Pressure Section: Servo controlled pressure section with (1) large driven roller and (2) cantered idle rollers. Straight and tapered pressure rollers for perfect glued joints -- GLUING SYSTEM: "GUL Jet" thin film technology processes "EVA" or "PUR" Glue in Cartridge of Granulate Form, motorized, programmable glue nozzle (upper glue line) height positioning.Workstations: -- End Trimming Unit (1918-P): Front & rear 2 x 0.35 KW (0.5 HP) - 9,000 RPM motor each, uni-point swivel-axis for no re-indexing when changing from flush to bevel end trim (0° - 10° bevel),"PCS" programmable pneumatic change-over from flush to bevel. -- Multi-function Trimming Unit (1826 ): Servo controlled, 2 @ servo motors (1) for horizontal copy wheel & (1) for tool spindle position) programmable top & bottom unit 2 x 0.65 KW (0.87 HP) - 12,000 RPM each motor. Uni-Point design with no second adjustment, pneumatic, programmable tilt action for changing the degree of bevel, digital counters for vertical copy wheel position and pneumatic air cylinder for in/out pre-positioning of trimming motor. -- Trimming & Corner Rounding Unit (1833 MOT4): For linea

HOLZ-HER - CONTRIGA 1366, ...Edgebander (w/Premill & Corner Rounding) -- Specifications: NC Controlled Edgebander has the ability to program all functions including: Panel thickness, edge feed, glue application, end trimming, radius/fine trimming, corner rounding, scraping, and buffing. - Virtually eliminates setup time by selecting & loading program that automatically activates these functions simultaneously.Coil edgebanding up to 3 mm PVC cap.; 2-3/8" max. panel thickness; 7" min. panel length; powered pressure beam opening adjustments. Equipped with:"1961" Premilling Station: PC Controlled with up to 45 mm (1-3/4") milling height; (2) motors @ 2 kW (2.6 HP) - 9,000 RPM each. -- Features: Granulate glue system with: Hopper System with "floating" applicator nozzle & "quick melt" feature. -- Automatic magazine for coil, strip & solid edgebanding model "1901" with: TRACTOR-BELT Feed System, Heavy-Duty guillotine for 3 mm PVC. -- "1914" Pressure Section for 12 mm thick edgebanding with: (3) Rollers, each w/individual pressure control, powered 1st roller with electronic speed control synchronized with chain feed speed; Servo motor adjustment for edgebanding thickness from PLC. Workstations:"1819-1" Double motor (1 HP - 6,000 RPM motor ea.) end trim units with: "Uni-Point" Swivel system; "quick change" from flush to 0° - 15° bevel from operator panel. -- "1962" Top & Bottom flush trim unit: 2.6 HP - 200 Cy HF motors; 12,000 RPM cutter speed; NC Servo control, non-tilt. -- "1966" Top & Bottom fine trim unit with: Motorized 5-axis positioning; 1.5 HP - 200 Cy HF motors;, 12,000 RPM cutterhead speed; bevels 0° - 45°, Servo control; all adjustments programmable through the PLC. -- "1933 & 1934" 4-Motor corner rounding unit for top & bottom of leading & trailing corner when edgebanding all (4) sides; 0.7 HP - 200 Cy ea.; both motors with Servo positioning from control panel; Servo adjustment of entire unit (base). -- "1927" Scraper Unit: Finishing up to 5 mm thick PVC banding for radius range from 2 - 5 mm; vertical & horizontal tracing wheels, Servo positioning enabled through "PC"; Servo controlled in/out of base. -- "1964" Top & Bottom Glue scraper. -- "1851" Oscillating buffing unit: Cleaning & polishing of panel; (2) 0.25 HP - 1,440 RPM motors; tilts 0° - 45° vertically and 0° - 20° swivel on horizontal plane.Other Specifications & Features:Variable feed speeds up to 25 MPM (81 FPM); panel overhang beyond chain 35 mm (1.38"); features automatic track pad lubrication. Operator Interface:PPC-231 Controller for line control, glue temperature & flow, feed speed setting, and motorized holddown pressure beam adjustment. -- Frequency inverter, outboard panel support, and sound enclosure w/interior lights over all milling units. -- Actual Mode is HOLZ-HER CONTRIGA 1366

HOLZMA PROFIMAT HPL 500 38/16 REAR LOAD, AUTOMATIC PANEL SAW: -- Specifications: 149.6" (3,800 mm) Cutting length & pull-back; 6.7" (170 mm) max. main blade projection; 40 HP (29.8 kW) Main & 3 HP (2.2 kW) scoring motor. -- Saw carriage: Infinitely variable speed from 0 - 492 FPM (0 - 150 MPM), constant return of 492 FPM (150 MPM).Carriage is electronically & automatically controlled (cutting height & length) through the CADmatic according to the material/program being processed."Power-Loc" quick change system for fast and easy saw blade change.NC Controlled scoring saw adjustment from the control panel during operation -- Pusher Fence:Rack & pinion digital drives with AC Servos on both sides, forward speed 295 FPM (90 MPM), return speed 295 FPM (90 MPM).(7) Material clamps which open up to 6.7" (170 mm): (3) Standard clamps with two fingers & (4) clamps with one finger.(4) Trimming rakes for thin strips/scrap removal are attached at the clamps. -- Operator Interface:HOLZMA "Power Touch Control" IPC multi-tasking controller with Windows "7 PRO" + "CADmatic 4.0 PRACTIVE" operating system;Intel i5 Dual-core Processor, Intel HD graphics card, 4GB RAM, SATA 2-250GB hard drive, (6) USB ports, (1) serial port, ATI/DVI video port, Standard industrial keyboard connection,21.5" LCD "Touch-Screen" monitor with real-time moving 2D & 3D graphics (displays cutting dimensions & error diagnostic); virtually unlimited cutting dimension memory.(2) Ethernet 10/100 interface connections; downloading from office PC is possible. -- Rear of machine: Profile rails & "Combi-rollers" at 50 mm centers; (2) integrated front & cross-aligning units before cutting to prevent off-set panels within the same book. -- Front of machine: (3) Air flotation tables 85" x 31.5" (2,160 x 800 mm) with (1) central blower unit. -- Rear Lift Table:7-Ton (14,000 LBS), 4-Column electro-hydraulic powered rear lift table running lengthwise with fork cut-outs, 150" x 63" (3,800 x 1,600 mm) capacity. Powered rollers are 4.2" (107 mm) dia x 7.79" (198 mm) spacing, 39 FPM (12 MPM) infeed/outfeed speed; Feeding material from (3) sides is possible with additional roller conveyors.22" (560 mm) Max. bunk height from floor level; 30.7" (780 mm) max. bunk height with a pit or risers; -- Complete With: Holzma's Unique "EcoPlus" System offers energy savings up to 20%; Includes Standby button & IE3 energy efficiency Motors rating.Angular cross-cut fence; Automatic side pressure device integrated into the saw carriage for cross-cutting, the machine cuts left to right to the cross-cut fence.Front & rear forks electronically & automatically controlled through the CADmatic according to the material/program being processed.Min. side aligning dimension 0" (0 mm), max. side aligning dimension 149" (3,800 mm)."Power-Loc" quick blade change system for main/scoring blades. -- Options Include: (1) Non-Powered in/out-feed staging conveyor with fork cut-outs as pictured. Micro In-feed for thin an

HOLZMA HPL 380 43/16 REAR LOAD, AUTOMATIC PANEL + VrSS POST FORMING: -- Specifications: 169.2" (4,300 mm) Cutting length, 3.7" (95 mm) max. main blade projection, 28 HP (20.8 kW) main & 3 HP (2.2 kW) VrSS Post Form (Jump) scoring motor. -- Saw carriage: Variable speed from 16 - 426 FPM (5 - 130 MPM), constant return of 426 FPM (130 MPM); electronically & automatically controlled through the CADmatic according to the material/program being processed. -- Pusher fence;Rack & pinion drive on both sides, forward speed 82 - 262 FPM (25 - 80 MPM), forward speed is currently set at 0 - 82 FPM (0 - 25 MPM) per CE standards, return speed 262 FPM (80 MPM).(6) Material clamps which open up to 3.9" (100 mm); first (2) clamps with two fingers and the others with one finger. -- Operator & Machine Control:HOLZMA "Power Control 22" IPC multi-tasking controller with "Windows XP" + "CADmatic 4.0" operating system;17" TFT Flat-Screen display/monitor with real-time moving graphics (displays cutting dimensions & error diagnostic); virtually unlimited cutting dimension memory.Standard industrial keyboard; CD ROM & 1.44MB floppy drives; possible direct downloading from office PC through RS 232 or USB connection. -- Rear of machine: Profile rails & "Combi-rollers" at 50 mm centers; (2) integrated front & cross-aligning units before cutting to prevent off-set panels within the same book. -- Front of machine: (4) Air flotation tables 85" x 25.5" (2,160 x 650 mm), (1) central blower unit. -- Rear Lift Table:Automatic 4-column electro-hydraulic rear load lift table; 169.2" x 62.9" (4,300 x 1,600 mm) capacity; 4.2" dia powered rollers, 39 FPM (12 MPM) infeed/outfeed speed;22.8" (580 mm) max. bunk height without pit or risers, 30.7" (780 mm) max. bunk height with a pit or risers; 8,800 Lbs (4,000 kG) lift capacity. -- Complete With:Angular cross-cut fence; side pressure device for cross-cutting with front & rear forks electronically & automatically controlled through the CADmatic according to the material/program being processed; min. side aligning dimension 0" (0 mm), max. side aligning dimension 169.2" (4,300 mm)."Power-Loc" quick blade change system for main/scoring blades. -- Actual model is HOLZMA Optimat HPL 380-43/16.

HOLZMA HPP 380 32/32 FRONT LOAD AUTOMATIC PANEL SAW Specifications: -- 126" (3,200 mm) Rip cutting capacity & pull back; 3.74" (95 mm) saw blade projection.18 HP (13.5 kW) Main saw motor and 3 HP (2.2 kW) scoring motor; scoring saw adjustment via "CADMATIC" control. -- Saw Carriage:Variable saw carriage travel speed from 16 - 426 FPM (5 - 130 MPM), constant return of 426 FPM (130 MPM). -- Pusher Fence:Electronically controlled overhead program fence, equipped with (6) clamps that open up to 100 mm (3.9").Rack & pinion driven on both sides, forward speed of 262 FPM (80 MPM), return speed of 262 FPM (80 MPM). -- Operator Interface:HOLZMA Power Control with "CADMATIC" + "Windows XP" operating system; virtually unlimited cutting dimensions memory.TFT 17" Flat Screen monitor, REAL-TIME moving graphics; panel grooving & numeric display.Industrial keyboard, 1.44MB Floppy & DVD R/W drives, capable of online operation via RS 232 or USB port for possible link to an office PC. -- Complete with:Automatic "CENTRIC" side aligner with front & rear forks, holding ripped strips squarely against the right angle fence.(3) Front air flotation tables, 67" x 25" (1.700 mm x 650 mm). Rear support rails with non-marking roller modules. -- Options Include:Label Printer as pictured & label printing software -- Actual model is HOLZMA HPP 380 32/32.