DENRAY 9600 B Down Draft Sanding TableExtra large 48" x 96" table; Comfortable 36" working height. -- Powerful system with 4,800 CFM rating. -- 5 HP Motor with magnetic starter. -- Space-saving self-contained unit w/built-in dust drawers and high efficiency cartridge filters. -- No duct work, no loss of conditioned air. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Fully enclosed unit. -- "Self-Cleaning" System with push button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust that can be directed away from operator. -- Quiet operation with only 82 dB. -- Available options; (4) Swivel casters with (2) that lock in place, Auto-Self cleaning timer or muffler.

DENRAY 7200 B DOWN DRAFT TABLELarge 48" x 72" Table. -- 3,900 CFM rating after filters. -- 5 HP Motor w/magnetic starter. -- Space-saving fully self-contained unit: No duct work, no loss of conditioned air. Contains (2) cartridge filters that clean to 0.5 microns. -- Comfortable working height 36". -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- "Self-Cleaning" System with push button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust which can be directed away from the operator. -- 84 dBA Sound level. -- Options include; Timer to automatically clean filters without operator, (4) swivel casters (2) that lock into place, noise reducing muffler (Reduces volume by 10 to 12 dBA),Unit also available in 220 V single-phase.

DENRAY 3660B Down Draft Sanding TableConvenient 36" x 60" table with a 36" working height with DENRAY's Pulse jet Cleaning System. -- Rated at 3,400 CFM for fast, easy removal of dust. -- 2 HP 3-phase motor. -- Space-saving self-contained, double filtration unit with integrated table top surface filter and bottom filters on all (4) sides. -- No duct work, no loss of conditioned air. Sound level 74 dBA. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board with rubberized surface. -- Also available in 115 V and 220 V single phase

DENRAY 3672 B Downdraft Sanding Table.Convenient 36" x 72" Table, comfortable 36" working height w/ DENRAY's Pulse Jet Cleaning System. -- Rated at 3,500 CFM. -- 2 HP, 3-Phase motor with magnetic starter. -- Self-contained system with 80/20 cartridge filters which clean with a 99.95% capture rate at .5 microns. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Space-saving design with no duct work, no loss of conditioned air. -- Sound level at 78 dBA. -- Available options include: Exhaust chimney, exhaust mufflers to reduce sound level to 10 - 12 dba, casters and filter cleaning auto timer.

DENRAY 9600 Down Draft Sanding Table: Extra long 48" x 96" table with a 36" working height. -- Rated at 4,300 CFM with 3 HP motor. -- This model features the Tube Filtration System which cleans with a 99% capture rate at 1 micron. -- Includes: (4) Swivel casters, including (2) that lock in place. -- No duct work, no loss of conditioned air. -- Comfortable 1-1/8" thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface.

DENRAY 2872 B Down Draft Sanding TableThis model is great for medium sized jobs, and can be used for plastics, woods and finishing materials. The 2872B comes with 80/20 cartridge filters which clean with a 99.95% capture rate at .5 micron. This model comes standard with Denray's "Jet Pulse" push-button cleaning, rubber coated top, along with motor access on the left end and filter access on the right end.Large work surface on this 28" x 72" table with DENRAY'S Pulse Jet Cleaning System. -- Rated at 3,000 CFM, after filters, with 2 HP motor and magnetic starter. -- Space-saving self-contained unit w/built-in dust drawer. -- High efficiency cartridge filters (180 sq. ft. of cloth area) that clean dirty air to .5-micron. -- Includes: Push Button cleaning -- Quiet operation at only 74 dBA sound level. -- Comfortable 36" working height. -- 3/4" Thick steel-reinforced MDF board worktable with "non-marring" rubberized surface. -- This machine can be used in heavy wood, finishes, solid surfaces and stone type materials. -- Available options: -- Explosion Proof Motor (3 Phase only). -- Light Bar. -- Casters. -- Auto-timer. -- Muffler (reduces sound level 10-12 dbs.). -- 100% Spunbond Polyester FiltersCarbon Filter Bank (odor only). -- HEPA Filter bank. --Three-sided Hinged Safety Shield. -- Magnehelic Gauge. -- HDPE Plastic Tabletop. -- Hydraulic Height AdjustmentAlso available in 230V, 460V and 575V 3 Ph..

DENRAY 2872 G Downdraft Sanding Table for Metal GrindingDenray grind downdraft tables are made for the general grinding of ferrous metals and come equipped with water pans built over the filters to help protect them from hot sparks. The flame-retardant 100% Spunbond polyester cartridge filters clean to .5 micron. These tables come equipped with Denray's "Jet Pulse" push-button cleaning, which can be set with an automatic timer.Includes: -- 28" x 72" Table top work area. -- 36" Work height. -- 3 HP motor w/ 3,600 CFM. -- 18" Fan. -- 76 Decibels Sound Level. -- Auto-timer. -- Magnehelic Guage Available Options: -- Explosion Proof Motor (3 Phase only). -- Light Bar. -- Casters. -- Muffler (reduces sound level 10-12 dbs.). --Carbon Filter Bank (odor only). -- HEPA Filter bank. -- Fiberglass Grate top. -- Rubber Mat for Steel Tabletop. -- Stainless Steel Tabletop. -- HDPE plastic tabletop. -- Hydraulic Height Adjustment. -- Smoke Arm. -- Larger Motor/Fan Up-grade?

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EXTREMA - XP-126A: Planer with Helical Head26" x 11-3/4" Cap.; 5/16" max. material removal; 10-1/2" min. part length; 20 HP WESTINGHOUSE / TIKO belt driven motor; STEALTH helical carbide insert cutterhead: 6,000 RPM; variable speed feed: 20 - 75 FPM. -- Equipped with: Powered raise-and-lower of 27" x 35-1/2" table; digital thickness controller; sectional chipbreakers; sectional infeed roller & dual outfeed rollers; (2) adjustable bed rollers.

Extrema WS-110 Single Spindle Shaper -- 3/4" & 1" Interchangeable spindles. -- 3 HP Single Phase, 3,450 RPM motor designed for operation in most smaller shops -- Belt drive for spindle speeds of 8,000 & 10,000 RPM _ 2-5/8" capacity under the nut (3/4" spindle) and 3-7/8" vertical spindle travel will accommodate a variety of cutters. -- Large Table size 28" x 30" with a 6" max. dia. table opening -- Includes Fence assembly, miter gauge, 1/2" collet adapter, and power feeder.

Extrema XG12 Gang Rip SawSpecifications -- 12" long arbor for 11-3/4" max. cutting width and powered -- 50 HP main motor; --10" to 16" dia. blade runnin g at 3,200 RPM and with cutting depth from 1/8" to 5-1/8". -- Min. working length is 9-1/8".Equipped with & Features -- 3 HP feed motor for variable speed feed 30 to 130 FPM. -- Feed system provides power to Heat trreated chain for positive feeding; automatic lubrication of chain and race; low iol shutdown; -- (6) individually spring loaded top rollers; table is 15" wide x 109" long. -- .25 HP motor for power raise and lower of top feed rolls. -- Disc arbor brakes, carden shaft driven system, and interchangeable blade sleeves including sleeve changing rack. -- Swivel control panel and Square D electrical controls, solid cast-iron construction, -- Soft start, -- Triple anti-kickback fingers, and replaceable pressure plate. -- (4) Overhead LasersNote from the seller: Gang Rip Saw comes from a small 3 man shop.

EXTREMA - DCY-1425 L3 TYPHOON: Cyclone Filtration Dust Collection System -- Powerful 2-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system before passing finer particles through the fan & filter.Free air volume: Rated @ 10,500 CFM. Low noise operation. -- Equiped with: 25 HP Motor with a Soft Start already wired in. -- Rotary air lock with: 1 HP Motor @ 38 CFM. -- Standard support frame: LEG 3 164" clear height x 149" clear width x 91" clear depth. -- (2) DCF-327E Exterior baghouses for more than enough filtering capacity.

EZ CAR - (Used) Model A: Car Crusher Approx: 6,200 hours.New in: 1988.System Pressure: 2,500 PSI.Port Reliefs set at: 2,650 PSI.Cylinders: 10" Bore.Travel: 78".Shaft: 4" rod.OpeningSize: 20" x 8'-1" x 7'-7".OverallWeight: 61,000 Lbs.Length: 43'-1/4."Travel & operating height: 13'-1/4'.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

FARR GOLD GS4 DUST/FUME/MATERIAL COLLECTOR: 3,000 CFM Rated cap., 1,300 sq. ft. filter area from (4) cartridge filters, approx. 2.3:1 air: cloth ratio . -- Equipped with: 5 HP Pull thru motor; dirty air is pulled into the filter area at bottom of filter media section allowing gross dust particles to fall into collector barrels located beneath pyramidal hopper discharging to a sealed drum (not included) -- Fine dust is pulled up thru the cartridge filters; dust filter cartridges are cleaned by automatic pulse jet with minimum compressed air consumption; cleaned air continues thru blower and is returned to the building air supply thru a silencer.. -- Includes: Cyclone with slide gate discharging into a sealed barrel (not included), electrical control panel, support stand with clearance under hopper, discharge for a waste bin,. access door, some pipe as pictured.

FELDER RL-350 Dust CollectorFelder clean-air extractors filter the air so that the dust remaining is less than 0.1mg/m cu. These exceptional air quality values are achieved by the position of the impeller. In other extracting systems, the impeller works by creating pressure between the machine and filter; with the Felder systems, the impeller is located on the clean-air side creating negative pressure throughout the system so no dust can escape. Specifications: -- 15 HP blower with 13-3/4" in-let -- Max. airflow 4,705 CFM, nominal air flow capacity 4,072 CFM -- Static pressure 9.4" WG -- Compressed air connection for automatic cleaning function. -- Dust emission quality less than mg/m cu. -- Filter surface area 71 m/sq. -- Acoustic pressure 75 dB -- Chip volume 2 x 55 gal. -- Dimension / Weight: 104" L x 45" W x 89" H, 1,785 lbs.

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FELDER FORMAT4 - Profit H08: Flat Table Machine Specifications -- 4’ x 8‘ Flat Table Working Capacity: X: 2,500 mm (98.4";); Y: 1,250 mm (49.2";); Z: 85 mm (3.3";).Gantry Outrigger: (2) synchronized Servo drivers in the X-direction; max. speed rate: 25 MPM (985 IPM). -- (1) Servo Driver: Y-Direction; max. 25 MPM (985 IPM); (1) Servo driver: Z-Direction max.; 15 MPM (590 IPM); power transmission in X. -- Y Via rack & pinion ball bearing spindle on: Z Axis; axis runs on ground linear guides. -- Automatic Centralized Lubrication of all axes -- Nesting Table: (2) Stops in X-direction: (1) Stop in Y-direction, left rear side; (6) manual switches situated in front of the machine; heavy valve system. -- Phenolic Vacuum Table with: (6) Vacuum fields and manual field choice. -- Stop cylinder at: Rear left; (2) in X, (1) in Y direction; electric box front left with light barrier. -- 1 ST 305-01004. -- Configuration package "Professional" H08 13.25 10 kW (S6) main spindle: HSK F63 Left/right rotation; 1,000 - 24,000 RPM controlled by inverter. -- Drilling Head "DH8": (8) Vertical drills; 1,000 - 6,000 RPM; controlled by inverter; 8-position tool changer. Extraction Hood: (22) Separate connections -- Software: Compact; standard PC with Windows 7 Controller; control for the use of ISO-Code; WOODFLASH programs on the machine.Includes: 210 cbm/Hr BECKER Vacuum Pump.

FELDER - G-330: Edgebander0.4 - 3 mm Edge thickness cap.; 40 mm panel thickness; 3" min. width; 4-3/4" min. panel length.Equipped with: -- Quickmelt TEFLON coated glue pot for granular hot-melt adhesive. -- Heavy-Duty Guillotine: Up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations -- Single motor; Double Blade End Trim with: HF Motor; 12,000 RPM. -- Top & Bottom Flush/Bevel Trim: Bevels 0° - 15°; 1/2 HP motor - 12,000 RPM each. -- Open space at outfeed. -- Single feed speed: 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations; outrigger panel support; used tooling.NOTE: Seller states that the equipment has less than (500) hours of use!