BLACK BROTHERS “22-D 875-62"; TOP & BOTTOM GLUE SPREADER with 62"; working width. -- Upper elevator opening 0"; – 4";. -- 8-¾"; dia. Neoprene coated applicator rollers with 16 TPI Grooving. -- 6-½"; dia. Smooth Neoprene doctor rolls. -- 40 - 120 FPM Variable speed drive. -- Complete with: Push button magnetic starter, NEMA 12 electronics, safety guards, all warning labels.LITERATURE PHOTO - Not actual equipment offered, for reference only.

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. EPDM covered applicator rolls, 6-1/4" chrome plated doctor rolls, upper elevator opening 0" - 6". -- Single speed 1.5 HP drive for 88 FPM, NEMA 12 enclosures. -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar.NOTE: Very Good overall condition, but rolls will need to be recovered, and Seller has discounted price to reflect this expense.

BLACK BROTHERS TOP AND BOTTOM 775- HOT MELT Glue Spreader with 32" working width.7-3/4" Heated Adhesive applicator rolls, with flow controlled by Chrome Doctor rolls. -- Single speed feed drive motor, operating at approximately 88 FPM. -- It has a 32″ width capacity and a 5-1/2″ thickness capacity. -- The doctor rolls are in very good condition. The price listed reflects that the 2 applicator rolls need to be re-covered. Or we can have them recovered for you for an extra cost and re-install. Please contact us with your specifications as we do not recover rolls until a machine is sold as these machines are very application specific. Meaning type of material which is usually silicone or a blend and durometer.This Model 775 has been cleaned and checked, and it heats up, and runs as it should.

BLACK BROTHERS 775-56 Top and Bottom Glue Spreader with Extra Tall Opening for SIP PanelsDescription & Specifications:1. Top and Bottom glue spreader2. Upper elevator machine opening to 12 - 1/2" opening3. Pass line-height 30"4. Variable speed drive by inverter 40 - 120 fpm5. Electrical interlock on upper and lower Nip Guards6. Operating control bars7. NEMA 12 electrical enclosure 575 Volt, 3-phase power8. Coating rolls rubber 7 - 3/4" dia OD, 14 TPI with 1/2" Cross Hatch Grooving.9. Doctor rolls chrome 6 - 1/2" dia ODThis is a 2007 machine but has never been put into operation and is ready to go, it has 575 volts, you may need a transformer.

BLACK BROTHERS 22D-875-62 Top & Bottom Glue SpreaderSpecifications: -- 62" Working width, 8-3/4" dia. Grooved Neoprene applicator roll with 24 TPI, 6-1/2" dia. smooth Neoprene doctor roll -- Lower elevator opening 0" - 4-1/2", -- Single speed of 88 FPM with 1.5 HP drive; -- NEMA 12 electrics. -- Complete with: Push button magnetic starter, safety guards, all warning labels.

BLACK BROTHERS - 22-D-875-56, ...Roller Coater56" Nominal length; 8-3/4" dia. applicator, Chrome doctor roll, upper elevator and top only. -- Setup to 0" - 6" thick. -- Smooth EPDM applicator rolls and Chrome doctor rolls. -- Variable feed speed drive, pass line height 34". -- Drip Pan, Feed Pan, Continuous Flow Trough to be Stainless Steel or Teflon Coated. -- Trough for continuous flow 1" pneumatic pump and hose to supply product.Complete With: -- NEMA-12 Electrical enclosure, operating control bars, magnetic brake, electrical interlocks, reverse lockout and cleanup pan.

BLACK BROTHERS - 22-D-875-56, ...Roller Coater56" Nominal length; 8-3/4" dia. applicator, Chrome doctor roll, upper elevator & top only. -- Setup to 0" - 6" thick. -- Smooth Chrome applicator rolls and Chrome doctor rolls. -- Stationary feed speed drive, passline height 34". -- Drip Pan, Feed Pan, Continuous Flow Through. -- Trough for continuous flow 1" pneumatic pump and hose to supply product. -- (30) Day warranty for workmanship and manufacture's warranty for all parts used.Complete with: -- NEMA-12 Electrical enclosure, operating control bars, magnetic brake, electrical interlocks, reverse lockout, and cleanup pan.

BLACK BROTHERS - 22-D-875-32, ...Top Only Glue Spreader.Capacity 32" Working width. -- 8-3/4" Dia. Rubber roll -- 6-1/2" Dia. chromed steel doctor rolls. -- Top elevator opening w/Readout -- Constant pass line: 36-3/4" -- Outfeed roller conveyor -- 7.5 HP MotorComplete with:1 Spare rollerNOTE: Machine is currently wired for 220v

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. grooved rubber covered applicator rolls, 6-1/4" chrome plated doctor rolls -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar. -- Top elevator style glue spreader, constant pass line --Main Motor 1HP, 3ph --Feed speed 88FPM --Thickness adjustment via manual hand crank

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. Grooved rubber covered applicator rolls, 6-1/4" hard rubber covered doctor rolls --Main motor 1.5hp -- Bottom roll adjustment -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar.NOTE: Currently wired for 460v

BLACK BROTHERS 4010 Cold Press with Motorized OpeningEnd loading on 50" side, Platen dimensions: 50" x 122", single upper platen, motorized adjustable daylight opening of 4" - 55". -- Pneumatic pressure by (32) air pods in upper platen, producing 50 PSI specific pressure, max. air pod stroke 5-1/2"; -- Equipped with: Dual chain feed-thru system, with forward and reverse, for automated loading & unloading. 80 FPM fixed speed drive motor, air cylinders automatically raise and lower chain depending on the position of the Air Pods. NEMA 12 electrics and electrical power supply.

BLACK BROTHERS COLD PRESS LAMINATING LINE (Complete)With BLACK BROTHERS "APP PL" 5 X 12, 50 PSI END LOADING FIXED OPENING AIR POD PRESSCurrent Line Set Up: Infeed Scissor Lift, Panel Pusher, Panel Cleaning Brush, Glue Spreader, Stack-building Scissors-Lift, Laminate Rack over Conveyor, Stack Staging and press loading Conveyor, and Cold Press. -- Station 1: PNEUMATIC PANEL FEEDERPanel Pusher feeds individual panels from side loaded (w/forklift) scissor lift into panel cleaner. Photo electric eye activates arm that pushes panel into panel cleaner.Pusher arm: to feed panels into machine on demandSwitch: for remote mountingPass Line: 44", 24" Stroke with 4' of adjustment: to feed panels from 1/2 thickness, up to 250#, in lengths of 8', 10', or 12'; Controls on (Left or Right)NEMA 12 Enclosure with main power disconnect switch and over-current protection: (230 or 460) Volt, 3 Phase, 60 Hertz, 24 VDC Control CircuitsDual Limit Switch Arrangement: to control the Scissors Lift with "hand/auto" selector and a Barrier Guard to prevent double board feed. -- Station 2:SCISSORS LIFT 36" Vertical Travel foot operated raise/lower switch48" X 120" Plain Deck with 6,000 Lbs CapacityPin Adjustable Edge Guides, mounted on SL and Anchor Clips for mountingTransverse Conveyors with air brake to allow loading or unloading from side. -- Station 3:MIDWEST AUTOMATION "PC160" Panel Cleaner with 63" Working width capacity, (2) spiral type cleaning brushes, 0" to 3" thickness opening, single end adjustment with roll opening (scale-type) indicator;Variable feed speed 30 - 150 FPM with 1 HP - 1,725 RPM drive, (2) 6" dia. infeed and (2) 6" dia. outfeed rolls, variable brush speed with 3 HP motor. Equipped with: All guards, dust hoods, and magnetic starter. -- Station 4:BLACK BROTHERS "775" TOP & BOTTOM ADHESIVE SPREADER, 68" width capacityApplication: To apply water base adhesive to top and bottom Particle board, plywood and MDF substrateUpper Elevator: 0 to 4-1/2" OpeningRoll Opening Indicator: shows opening between rolls in 0.001 incrementsRiser Base: 44" pass line heightCaster Arrangement: (4) plain rigid casters with guide track and lockCoating Rolls: (2) 7-3/4" Maximum O.D., 60 Durometer - Neoprene/SPR, Grooved: 16 TPIDoctor Rolls: (2) 7" Maximum O.D., 100 Durometer - Ebonite, Ground Smooth Single Hand-wheel Doctor Roll Adjustment with mechanical digital read-out. Electrical Interlocks on nip-guard(s)NEMA 12 Enclosure with main power disconnect switch and over-current protection.1-1/2 HP Single Speed with 3" reverse Lockout 88 FPMPivoting In-Feed TableOperating Hand-wheels & Controls: Parallel to the direction of flow on the right Motor On Left EndOperating Control BarsLiquid Level Control: FIBER OPTICMachine Mounted Double Diaphragm Pump: l" Ports, Aluminum body with Neoprene diaphragm Feed Lines:Automatic Roll Cleaning Arrangement -- Station 5:Hydraulic "Conveyor-Lift" with conveyor roller top: as the board leaves the spreader, the person on each corner guides the pane

BLUE GIANT SFSRH33/575 Scissor LiftHydraulic 3,000 Lbs. scissors lift -- 34" x 108" platform with idle roller -- Low 9" x high 53",Hydraulic pumping unit with 3 HP motor.

BLUM - Mini Press, ...Hinge Borer. -- Tabletop "Mini Drill" unit for BLUM Hinge Boring; 1.5 HP (1.1 kW) - 2,450 RPM drill head assembly for hinge cup boring. -- Head assembly rotates for several hinge & drawer system boring patterns; pneumatic drill cycle with air blow off. -- Includes: 48" x 24" Tabletop. -- Machine also used for line boring by purchasing an auxiliary BLUM spindle head; not included. Complete with: 3-Drawer mobile storage base for all hinge components.

Boarke BKM-43103RRK (3) Head 42″ Wide Belt Sander (3 NEW DRUMS)43" Width cap. Drum, Drum , PlatenHead Configuration1st Head : 30 hp, 10″ Helical grooved drum,2nd Head: 25 hp 10″ helical grooved drum,3rd Head: 20 hp helical grooved (idler) with a platen. Specifications -- 42″ width capacity, a 5″ height capacity running -- 43″ X 103″ abrasives. -- First head is a 30 hp, 10″ Helical grooved drum, -- Second head is a 25 hp 10″ helical grooved drum -- Third head is a 20 hp helical grooved (idler) with a platen. -- First and second heads have dial indicators to dial in abrasives. It does also have the optional 5 hp vacuum feed bed.Equipped with & Features -- The feed is variable from 7-45 FPM via a 2 hp motor and has a VFD for the speed control. -- The feed mat is thick and has the usual crazing but has plenty of life. -- Elevation is handled by a 1/2 hp motor. -- This machine does have a digital read out and touch pad control combined with an auto thickness calibration unit on the right.

BOERE - TKS 900, ...2-Head Top Wide Belt Sanding Machine900 mm (36") Working width; equipped with: (1) Contact roller, (1) Fine sanding pad. Head Configuration -- 1st Head: Rubber contact roller, spirally grooved, Shore hardness 80, diameter 265 mm (10.4"), driven by 18 kW (25 HP) motor. -- 2nd Head: Sanding pad, electronic-pneumatic controlled, 114.7 kW (20 HP); Air blowing unit for cleaning the abrasive belt. -- All heads use abrasive belts size: 910 x 1,900 mm (35.8" x 74.8").Feed System -- Variable feed speed: From 5 - 25 MPM (16 - 82 FPM); 1.5 kW (2 HP) motor. -- Motorized part thickness opening: 3 - 150 mm (0.1" - 6"), driven by 0.12 kW (0,15 HP) motor.Complete with: -- Emergency Stop Systems for abrasive belt breakage and low belt tension. -- Infeed safety bar for operator protection and oversized parts. -- Automatic Star Delta starters, motor load meters. -- Pneumatic belt tension. -- Emergency Stops at the front & back. -- Extended infeed belt, approx. 42" long.Actual model: BOERE "TKS 900".

CAM-WOOD TRS-405-SS Short Stock Rip Saw ...with the following specifications and features:Specifications: -- Max cutting width: 12.6"; -- Min length part: 3.15"; -- Short stock ratio of thickness to length: 2:5 -- Distance from center of chain to throat, 30"; -- Saw arbor powered by 50 HP Std. - 30 HP, 60 HP and 75 HP optional -- Spindle speed, 3,200 RPM -- Sawblade diameter to thickness: 10"; dia = 2"; thick, 12"; dia = 3"; thick, 14"; dia = 4"; thick, 16"; dia = 5"; thick -- Sleeve diameter (sawblade bore), 70 mm -- Sawblade keyway, 2 each 20 mm wide -- Spacer size, 70 mm ID x 95 mm OD -- 2 HP feed motor, 3 HP optional -- Variable feed speeds from 20 to 80 FPM -- Head elevation powered by ¼ HP motor -- With (2) 6"; dia. dust outlets -- NET weight, 5,500 Lbs. Features and Benefits: -- Exclusive feed track - Design for short stock feed – see literature! -- Exclusive length capacity on a standard Gang Ripsaw, as short as 3";! -- Turn waste blocks into useable parts -- Pressure rolls supported from both sides hold stock securely for even, smooth ripping -- Pressure plate (hold-down shoe) supported from both sides; helps prevent split parts from damaging sawblades -- Power raise and lower for overhead pressure roll and hold-down assembly -- Variable feed speeds allow ripping a variety of material, hard or soft, thick or thin -- 2-Top and 1-bottom rows of kickback fingers plus side splitter guards provide operator safetyNOTE: ...Where have you seen a Gang Ripsaw capable of ripping as short as 3"!!! ...Also perfect for slats!

TRS-460M4 Multiple Blade Rip Saw w/Optimizing, (4) SHIFTING BLADES &#9679 WITH 18" OF USEABLE ARBOR SPACE!Specifications: -- Moveable sawblades when using the Optimization program.1-1/2"; minimum distance between movable saw blades -- Sawblade configuration with (4) movable saws and (1) fixed sawblade -- Sawblades are optional -- Infeed & outfeed roller tables are optional -- With 50 HP saw arbor drive motor and 3 HP feed motor -- Pressure rollers elevation motor: 1/2 HP -- (4) 1 HP servo motors for shifting sawblades -- Fence adjustment is manual. -- (4) 0.13 HP servo motors for shifting Laser Lights -- With (5) Laser Lights -- UL electrical components. -- 10 to 130 FPM variable feed speed -- 18"; Max. distance between fixed saw and the last (outside) movable saw -- 31"; Max. material feeding width -- 27"; Min. cutting length -- (2) 6"; Dust hoods -- Cutting depths: 10" blade, 1.65"; thick ; 12"; blade, 2.65"; thick; 14", 3.66"; thick; 16" blade, 4.64"; thick -- Sawblade size vs. RPM. Make Blade size clear when order) -- Spindle speed @: 3,800 RPM (10" & 12"sawblade) / 3,000 RPM (14" & 16"sawblade)Computerized Rip Optimizing Program, Included: -- The operator only sets a line for total width, then the computer performs optimized ripping according to sizes set on the job sheet and the priority mode set from these options: -- 1. Priority according to the widest -- 2. Priority according to the same size -- 3. Fixed-width ripping -- 4. Yield priority -- 5. Value priorityOPTIONAL MODEL TRS-460M4-INCOV 3500mm AUTOMATIC INFEED CONVEYOR SYSTEM WITH SCANNER AND OPTIMIZING SYSTEM, add $198,000 -- Automated infeed system, speed rate controlled by electrical clutch connected with the Ripsaw's feed chain -- 13' max. infeed length with (16) width detectors (scans every 8") -- Special pressure roller set, motion with liner rail and air cylinder -- Width scanning by sensors, with optimizing program for auto calculating -- Moving fence by servo motor, according to the wood width

CAM-WOOD AC-100120 Piston Air CompressorHeavy Duty unit with a 10 HP induction motor.Features & Specifications: -- 34.2 CFM @ 90 PSI, Splash lubricated cast iron 2-stage pump. -- Automatic start/stop operation. -- 120-Gal. horizontal tank that meets the ASME standards. -- Manual tank drain & pressure gauge. -- Deep finned after-cooler. -- Fully enclosed belt guard and ON/OFF pressure switch. -- Deep finned cylinder head for cooling and replaceable air filter/silencer. -- Durable painted finish for years of service under the worst conditions.

Cam-Wood TRS-MR-1300 X 75mm Roll Feed Gang Rip SawSpecifications -- Working thickness: 10 - 100mm • -- Working width: 530 - 1300 mm • -- Working thickness : 10 – 75 mm / 100 mm • -- Saw Blade 14", • Washer Diameter 110mm • -- Minimum length of work piece when feeding consecutively: 600mm • -- Number of spindle : 1 • Equipped with & Features -- Up & down motor : 1 HP x 1 • -- Feed speed : 6 - 15 M/ min. • -- Feed motor: 7.5 HP x 1 with Inverter • -- Multiple rip saw spindle motor:150 HP / 200 HP • -- Spindle diameter : 80 mm with two key-ways 10 mm5 mm • -- Spindle R.P.M.: 4,000 R.P.M. • -- Movable 1300 mm Saw Shaft Support for easy saw blade replacement.