WILTON 4421-2 20" Pedestal-Type Disc SanderSpecifications: -- Table size 10-1/2" x 27-1/2", Table tilt 45° Out/30° In, Table can be lowered below disc to accommodate large workpieces.Equipped with: -- 3 HP 1,720 RPM Direct drive motor, Low voltage protection switch. -- Positive lock rack & gear table tilt.

5 HP - 1,200 RPM motor, roller table size 32" x 84", horizontal travel stroke 38", adjustable height of table base from 26" to 35" via large hand wheel. -- Rubber-faced Aluminum Pullies 8-1/2" face x 16" dia., accepts 6" wide abrasive sanding belts, pulleys can be spaced to accommodate various belt & material sizes, belt loop travels over table with manual handwheel belt tension & tracking. -- Includes: Magnetic starter, dust hoods

WYSONG & MILES 604 DOUBLE SIDED OSCILLATING EDGE SANDERDouble Sided Oscilating Edge Sander with 7.5 HP - 1,800 RPM TEFC motor; (2) 11" x 60" cast iron platens; 10" x 172" abrasive belt size, (150) oscillations/Min with 1/2" movement, 0.5 HP oscillation motor.Equipped with: -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table; tables tilt 30° up & 45° down; 5" vertical table travel w/hand wheel adjustment, 5" lateral side table travel w/hand wheel adjustment, 4-1/2" lateral end table travel w/handwheel adjustment. -- 10" Dia. x 10-1/2" face direct drive pulley, 4-1/2" dia. x 10-1/2" idle pulley. Complete with: -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

WYSONG & MILES Edge Sander6" x 32" Graphite mocovered wooden platen, Double 8" x 34" tilting side tables, full 180ø steel end table, tilts and raises & lowers. --2 HP motor, direct drive motor.

WYSONG & MILES NO. 303 COMBINATION DISK AND OSCILLATING SPINDLE SANDERThis machine is two in one. It features a 26″ disk sander with a 15″ X 34″ titling table (to 45 degrees) on one side. On the other you will find an oscillating spindle sander featuring a 24″ X 24″ tilting table (15 degrees forward and 35 degrees backward) with a 2″ X 8″ oscillating spindle. -- Power for each is provided via a 5 HP motor. A swing out arm holds a 2 gallon bucket to the side of the machine for small parts or waste. -- Machine is 220V/440V/3 Phase. -- The only repair we see is a braze on the motor mount which is a very old repair and does not effect machine operation. &#9679 This fully functional machine has been fully cleaned and checked

COSTA - ACCT1350, ...3-Head Wide Belt Sander 53" Width cap.; Drum, Drum, and Platen.Head Configuration:1st Head: Rubber covered contact roll, 9.8" dia., 30 HP motor.2nd Head: Rubber covered contact roll, 9.8" dia., 25HP motor.3rd Head: Polishing platen "jump type"; pneumatically controlled with timers to eliminate any dubbing of leading or trailing edges on panels; 20 HP motor.Specifications -- Contact rolls with pneumatic "grit-set" thickness control with a 4-position turret actuated from the control panel (this adjusts the contact roll for varying thickness of abrasive belts). -- 53" x 103" Abrasive belt length with electronic tracking; --Motorized part thickness opening on conveyor bed, 1/8" - 6 max. thickness opening. --2-Speed conveyor belt feed from 16 - 33 FPM --Vacuum conveyor bed assemblyEquipped with & Features --Thin veneer" sanding package with floating or rigid bed with infeed & outfeed spring loaded holddown shoes. --Oscillating sanding belt cleaners with timed entry -- All motors with Y-Delta starters, motor load meters --Infeed & outfeed conveyor extension tables with rollers, and (3) 6" OD. dust outlets.

Costa S6 XUT 1350 3 Top Head Wide Belt Sander53" Width cap, Crossbelt, Combination Head, PlatenHead Configuration1st Head :Transverse Belt Unit -- Transverse Belt Width: 5.9"; (150mm) -- Transverse Belt Motor: 14.75 HP (2nd Head: Combination Roller-Rad, Steel Roller3rd Head :Segmented Pad Unit with Superfinishing Belt, Motor Power: 20 HP (15 kW)Specifications -- Max. Sanding Width: 53.15"; -- Sanding Belt Width: 54"; (1380mm) -- Min. Sanding Thickness: 0.12"; -- Max. Sanding Thickness: 6.3"; -- Vacuum belt with fixed pass height -- Feed Belt Speed: variable up to 82 ft/min. -- Feed Belt Motor: 3 HP (2.2 kW)Equipped with & Features -- Top brush on the outfeed -- Single 3kW fan for vacuum feed belt -- Machine Programming Software: LOGIC A -- Total Installed Power: 112 HP (83 kW)

COSTA KH2 CCCT 1350 Wide Belt Sander (4) Heads52" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Steel contact roll, 9-7/8" dia. , 45 HP motor;2nd Head: Rubber covered contact roll, 9-7/8" dia., 45 HP motor.3rd Head: Rubber covered contact roll, 9-7/8" dia. 60 shore, 30 HP motor.4th Head: Finishing Platen, 23 HPSpecifications -- 53" x 103" abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking. -- Controls with PLC processor, -- Pneumatic grit compensation with 4-position stops. -- Variable feed speed conveyor with inverter control 16 - 82 FPM.Equipped with & Features -- Vacuum conveyor bed assembly with 5.5 HP suction fan and motor. -- Infeed & outfeed spring loaded hold down shoes on all heads. -- Powered raise & lower conveyor bed with LED readout and motor load meters.

COSTA - KBH CCCT 1350 & KH2 CCCT 1350, ...Top & Bottom Sander Line.Head Configuration:Machine #1 - "KBH CCCT" 4-Head Bottom Sander. Bottom Head #1: ~10" Dia. grooved Steel Drum, 47 HP motor. Bottom Head #2: ~10" Dia. grooved rubber covered contact drum, 47 HP motor. Bottom Head #3: ~10" Dia. grooved rubber covered contact drum, 32 HP motor. Bottom Head #4: Finishing platen, 23 HP motor.Machine #2 - "KH2 CCCT 1350" 4r-Head Top Wide Belt Sander. Top Head #1: ~10" Diameter Grooved Steel Drum, 47 HP - 460 V motor. Top Head #2: ~10" Grooved rubber covered contact drum, 47 HP motor. Top Head #3: ~10" Grooved rubber covered contact drum, 32 HP motor. Top Head #4: Finishing platen, 23 HP motor.Specifications: -- PC User interface for each machine. -- Sanding belt size: 53" x 103". -- 96" Belt conveyor in between machines. -- 20 HP Vacuum Blower for each machine's vacuum bed.

---In Auction--- COSTA BL 1350 1,350 mm (53.15") 4-Head Denibbing Sander, with (2) Cross Brush Belts & (2) Brush Rolls --Never used! Bought new for project that was cancelled!-- Specifications: Thickness cap. 1/8" - 6-1/4". Cross brush speeds belt 3 - 26 FPS. Brush roll speeds 130 - 1,300 FPM. Feed speeds 16 - 82 FPM. Equipped with: 1st & 2nd Heads: Each with 2” W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. (3) 2” Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. 3rd & 4th Heads: Each with 62” L x 16” Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. 2-5/8” dia x 7/8” w swivel rubber wheels before each brush roll head. (1) 2” Dia. Rubberized hold-down roll after last brush roll head. 53-1/2” W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2” W & 2” L Centers, 2-1/2” Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. Control motor load meters. Complete with: Instruction Manual. Details, Photos, Videos: https://exfactoryauctions.com/Detail/FD-230114/event/A051324$1

CROUCH 250-F EDGE SANDER37" x 6" graphite coated platen, 2 HP motor, . -- Equipped with: 9" x 36" side table with adjustment; 10" x 32" end adjustable table.

CROUCH 81-70 EDGE SANDER (NON-OSCILLATING)5 HP Direct drive motor, 6" x 144" abrasive belt size, (1) 8" x 56" Platen;Equipped with: -- (1) 12" x 56" Adjusable Side table and (1) 15" x 28" End table;. Tables adjust vertically 5" and laterally 2-1/2". -- 8" dia. rubber covered drive pulley and 4" dia. aluminum idle pulley;

DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350

DMC - 1350 RK, ...TECHNOSAND Dual Head Wide Belt Sander.(2) Heads, 52" width cap. - Head sequence: Contact sanding roll and Segmented platen. Head Configuration:1st Head: 7" (175 mm) Dia., 85 durometer rubber-covered calibrating contact sanding roll.2nd Head: Segmented finishing platen with EPICS (sectional electronic pad) with (46) electronically controlled air segments.Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 1.5 HP feed drive, vacuum conveyor bed with 7.5 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Message from the Seller: The machine was setup by a DMC tech. It has a new calibration roller & new bearings, rebuilt HYDRA 35 controller; currently under power, comes with dust collecting manifold and hoses, plus the machine can be loaded onto a flatbed for ...$ 600.

DMC - EuroSystem SY-TC 1350, ...Heavy-Duty 4-Head Wide Belt Sander53" Width cap. Drum, Drum, and Drum; Segmented Platen.Specification; -- Max. workpiece width: 53". -- Workpiece thickness: 0.32" - 6.8".Head Configuration & Feed: -- 1st Sanding Unit: 10"; Diameter grooved steel contact drum; 60 HP motor. -- 2nd Sanding Unit: 10"; Grooved rubber covered drum, 27 HP motor. -- 3rd Sanding Unit: 10"; Grooved rubber covered drum; 20 HP Motor. -- 4th Sanding Unit: Electronic segmented platen; 35 HP motor. -- Belt size of 53" x 103". -- Feed Motor: 5 HP, Variable feed speed. -- Vacuum Bed. -- Constant Pass Line.Equipped with & Features: -- Power Panel Touchscreen Control. -- Shoe type holddowns. -- Amp meters for all Sanding Units.

DMC UNISAND K 1350 M2 1,350 mm (53.15") 3-Head Veneer SanderFor lacquer sanding, veneer cut, light calibration cut.NOTE: The following specifications need to be confirmed by Seller.Specifications: -- Working Thickness 4 - 200 mm (0.16" - 7.87"). -- 1st Head: TA Cross belt sanding unit, with Electrically-controlled link sanding pad, 150 mm x 6.550 mm (5.91" x 257.87") Sanding belt, Variable sanding belt speeds 2 - 20 MPS (6.6 - 65.6 FPS), 15 kW (20 HP Motor), -- 2nd Head: "R-320" 320 mm Dia. (12.60") Shore 40 SH Spirally-grooved contact roller, Soft rubber version, 1,370 mm x 2,620 mm (53.94" x 103".15") Sanding belt, Variable sanding belt speeds 2 - 20 MPS (6.6 - 65.6 FPS), 15 kW (20 HP Motor). -- 3rd Head: Superfinishing pad with "EPICS" Electronic sectional pad, (46) Sections, 1,370 mm x 2,620 mm (53.94" x 103.15") Sanding belt, Variable sanding belt speeds 2 - 19 MPS (6.6 - 62.3 FPS), 15 kW (20 HP Motor), Pneumatic belt tensioning, Intermittent belt-emitting device, Automatic infrared band control.Equipped with: -- Oscillating belt cleaning blowers on all heads. -- Vacuum conveyor feed belt, with Variable feed speeds 3.5 to 18 MPM (11.5 - 59.1 FPM), 4 kW (5-1/2 HP) Drive motor, 15 HP Blower motor with Fan silencer. -- 200 mm (7.87") Dia. Panel cleaning brush with 1.5 kW (2) HP Motor. -- "HYDRA V-PAD" Touchscreen control.Weight: 10,500 Lbs.

DMC - UNISAND 2000-M2, ...Wide Belt Sander (2) Heads -- 53" Width cap. Drum, Platen.Head Configuration: --1st Head: 11" dia. (300 mm) Rubber-Covered Contac; (2) speeds or inverter adjustable 20 - 25 HP; Varied RPM. --2nd Head: Combination head with drum and graphite covered 2-1/2" finishing platen; 25 HP.Specifications: -- 54"x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computor controlled; set-up functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with: 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with: LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, motor load meters.2-Roll infeed conveyor extension; high efficiency dust extraction.

DMC - TC1100 1M3, ...6-Head Top & Bottom Sander(3) Heads bottom and (3) heads top; 1,100 mm (43") max. width. Head Sequence for Each Top and Bottom Machine -- 1st Head: Rubber-covered contact roll, 30 kW (40 HP) motor. -- 2nd Head: Rubber covered contact roll, 22 kW (30 HP) motor. -- 3rd Head: Finishing platen, 14 kW (19 HP) motor. -- 4th Head: Cleaning brush, 0.9 kW (1.2 HP) motor. -- Extra-long feed belt of 43" x 102"; long abrasive belt with electronic tracking. -- Variable feed speed from 11 - 60 FPM; 1/8" - 4" motorized part thickness opening with LED readout. -- 43" Wide Vacuum feed belt. -- (2) Vacuum blowers with 12 HP motor. -- Separate controls for each machine (in same control cabinet).

D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

DMC UNISAND K 1100 Wide belt sander4-Head, 43" (1,100 mm) max. width cap. Head sequence: (3) Contact rolls and (1) Combi with roller and segmented platen.Heads configuration: -- 1st Head: Helical grooved steel contact roll, 10" dia., 48 HP motor. -- 2nd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. and 65-Shore covering hardness, 35 HP motor. -- 3rd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. 45-Shore covering hardness, 30 HP motor. -- 4th Head: Combi head with roller covered with rubber, 30 shore and Finishing sanding pad unit , 30 HP 2-speed motor with segmented pads pneumatically controlled -- All heads use 44" x 103" (to be confirmed) abrasive belts and are equipped with electronic tracking, automatic tensioning, automatic emergency breaking, and oscillating sanding belt cleaners.Controls: -- "HYDRA V-PAD" 10" Touch-screen computer for setup functions, color LCD Display, allows operator to setup/recall part thickness, -- Conveyor feed speed (3.5 - 18 MPM), -- Abrasive belt direction, and reversible speed setting of 4th head. -- Conveyor belt feed with inverter control, feed speeds from 11 - 60 FPM, 5.5 HP feed drive; -- Infeed & outfeed holddown pinch rolls on all heads, automatic part thickness setup, -- 2-speed motorized part thickness adjustment, 1/8" - 6" max. opening; -- Infeed & outfeed motorized conveyor extension rollers, automatic part thickness setup sensor. Complete with: -- Safety stop at infeed, -- Anti-kickback device, -- Infeed & outfeed emergency stops, -- Motor load meters, i -- Infeed & outfeed idle rollers, -- High efficiency dust extraction, and control console with monitor.Note: (spare parts not installed) New feed belt , new front pressure roller, new front pressure bar and several new small parts for approx $15,000 of value +11 boxes (approx 5 belts/ box) sanding belts 100 grit, 120 grit, 180 grit and 220 grit.