Baker Model A Resaws comes with: Return conveyor, Powered Hold Down, Power Hold Over, Infeed/Outfeed Turnarounds, 240V 3Phase

Used/Reconditioned 1998 Baker Model “A” Resaw with Slide Return This is a Reconditioned 1998 Baker Model “A” Resaw with Powered Slide Return Conveyor and is Wired for 480 Volt 3 Phase. Machine has had 2-161900 Recrowned and Rebalanced 28” Band Wheels, 1-161387 Return Belt, 2-141021 Top Guide Shoes, 2-141003 Top Guide Pads 1”, 1-141004 Bottom Left Guide Pad 1”, 1-141005 Bottom Right Guide Pad 1”, 2-141001 Guide Rollers, 1-164358 6” Conveyor Beam and Hold Down Stand, 1-161126 T-Handle for Blade Tensioning, 2-111013 5VX710 Belts, 1-111002 B38 Belt, 1-171117 Blade Brush, 1-161836 Front Hold Down Slug, 1-161243 Acme Hold Down Adjuster, 4-131040 50B12 1” Bore Sprocket, 8-181080 1” Bearings, 1-181019 Hydraulic Tank Filter, and several other Miscellaneous items have been replaced on the machine including but not limited to Springs, Suction Hoses, #50 Chain, Hydraulic Belt Extenders, O-rings, Hose Ends, Slide Return Shear Off Arm and T-Handles for Shear Off Arm.

This is a slightly used 2022 model 26” air activated chop saw with a 15hp motor wired for 480 voltage. It comes complete with the electric panel and controls. It has a 10’ idler infeed roll case with fence and a 5’ idler outfeed with a 48” stop bar and 4 manual stops.

Baker Products’ Self-Dumping Steel Hoppers can be used to collect almost anything. It has a reinforced base and continuous weld. When the hopper is full, you can easily pick it up with almost any forklift and dump it simply by pulling a lever. It has a lock, so the load will not dump by mistake. The Baker Self-Dumping Steel Hopper is a convenience every company should have. A. 2 yd (1,828 mm) 603 lbs. (274 kg) B. 2 yds (1,828 mm) 805 lbs. (365 kg) C. 3 yds (2,743 mm) 971 lbs. (440 kg) A. 44” (111.8 cm) 59” (150 cm) 69½” (176.5 cm) B. 45½” (115.6 cm) 57½” (146 cm) 64½” (163.8 cm) C. 55” (139.7 cm) 58” (147.3 cm) 71” (180.3 cm) Forklift Opening: 2½” (6.4 cm) high by 48½” (123.2 cm) wide

2013 Baker M4I DeDuster with hopper infeed and variable speed drive and three 2hp brush heads. Electric complete with 480 voltage, panel, and pedestal mounted start and stop station. $6,500.00

The Baker M4i DeDuster has been designed to be a super-high-performance dust removal machine that will accept and remove sawdust from the highest production multi-head horizontal band resaw today. The M4i DeDuster can operate at over 700 feet per minute! Boards drop into the M4i DeDuster hopper. The hopper’s height adjustment (for the amount of lumber), indexable stops (for the length of the lumber), and adjustable fence (for the width of the lumber) allow you to set it up for the most efficient operation. This virtually eliminates jam-ups. The hopper’s variable-speed conveyor sends the lumber through the M4i DeDuster chamber one piece at a time. The rear height adjustment of the conveyor can be adjusted from a minimum of 24" and up to 34" maximum. Inside the M4i DeDuster chamber, high-speed brushes clean all four sides of the boards. The independently powered brushes are fully adjustable for longer brush life. The specially designed chamber maximizes air flow, directing the dust out the dust chamber instead of back onto the boards. The entire side of the chamber easily opens for full open accessibility. The Baker M4i DeDuster comes with its own electrical panel and a stand-mounted, remote start/stop control station.