You Have Selected
 
 
  • Used
  • New
 
  •  
 
  •  
 
  •  
 

 
14 Results Found for Woodworking Viewing 1 - 14 of 14 results
Call
used 50 inch feeder, 36" x 50" feeder, Archer 36" x 50" feeder airlock, used Archer 36 x 50 feeder airlock, Archer model# 36/50 , 1 inch thick knifes/blades, overall height 44 1/2", can provide video demonstration of gear box motor running, repainted blue, more photos available before and after paint,
Equipment Location:Toledo, WA
$9,500
•Burelbach 4 x 10ft stacker •Removed from plywood mill that went out of business, was in use at time of shut down •Currently stored inside
Equipment Location:Toledo, WA
$14,500
•Durand plywood stacker •Will stack panels up to 5ft wide x 10ft long panels •Serial # 1286 •Was in use on skinner/trimmer line when the plywood mill went out of business •Currently stored inside, and ready to load on a truck •No charge for loading
Equipment Location:Toledo, WA
$9,500
Gruendler Wood Hog •Model 24-3 •Horizontal feed •Serial# 21444, •GE 75HP 220/440 volt 1775 RPM main motor, •Direct drive, 3/4HP infeed motor for feed wheel, •Bottom discharge is 10 inch diameter . •Hammers are 1 1/2 in width. •Rotor width is approx. 24 inches. • Infeed opening is 3 inches tall, infeed opening width 17 1/2 inches. •We can quote you a delivered price to your location. stored inside. motor test available
Equipment Location:Toledo, WA
$21,500
•Jacobson / Carter Day XLT Full Circle Hammermill, •125HP •Reliance XE Energy Efficient Extra Tough direct drive motor •460 volts •1785 RPM •Model # 42315 XLT •Serial# 39960 •1/4 inch thick hammers •Inside width approx. 14 inches •Top Gravity feed • Left side and or right side discharge •Large side access rolling panels for easy rotor and hammer access •Motor starter •Prior use was grinding straw • Stored inside •Motor test available Have a starter that came with Hammermill, but don't know if if works or is the correct size. •Can quote you a delivered price to your location
Equipment Location:Toledo, WA
Call for Price
Jenkins 191SB slatbed 10ft saw, Kohler General Jenkins 6 head slat bed 10ft saw, 6 movable saw heads are attached to air cylinders to raise and lower each individual saw head independently also adjust left and right, 40HP common arbor, can cut up to 10ft + long panels, spare parts included, removed from service June 2017-stored inside our warehouse, Jenkins model# 191 SB, serial # 1159, variable speed infeed, dust collection hoses/manifold included (in photo), saw was removed from the original location in one piece for easy installation - and will ship in one piece (over sized-width load - we have photos of the saw loaded on the semi truck), approximate overall saw footprint: 12foot 9inches wide X 17foot long +-, call or email for a delivered price to your location, stored inside our warehouse, we can test run saw motor and provide video to buy, more details and photos available- please contact us with questions or more photos.
Equipment Location:Toledo, WA
Call
Ferrari resaw, Ferrari band resaw, Kimwood Ferrari 42 inch tilting infeed band resaw, 42 inch vertical band resaw variable hydraulic infeed, infeed tilting table has 4 powered rolls. Capable of using a 6-inch wide blade down to a 2 inch wide blade, Made in the USA, in Oregon. , always operated inside and currently stored inside. Removed from service in June 2018. More information and photos available, call for a delivered price to your location. price includes loading on to your truck. • infeed rolls can be tilted • Capable of sawing jambs, headers, casings, and sidings in multiples with close tolerances. • Variable speed hydraulic feed rolls drive from 40 to 400 fpm. • Hardened tool steel knife edges on all the strain components. • Utilized anti-friction bearings throughout. • Patented top and bottom saw guides. • Sniping eliminated due to the placement of feed rolls. • Guides adjustable while machine is running. • Saw Specifications: 18 to 21 gauge with 18' 6" minimum and 20' 6" maximum lengths and up to 6" wide
Equipment Location:Toledo, WA
Call for Price
Tri-State Resaw by Kimwood Corp. Model T-36-4 36” X 3 1/2” wheel size and recently reground 20 HP motor with AC inverter controller variable speed. Feed rollers recently rebuilt. All electrical in working order. Tilting feed operates up to 45 degree angle, spring loaded with blade tension. Rebuilt upper and lower block pressure type blade guides. Feed speed varies from 10 to 250 FPM, (VFD) 2 variable frequency drives, one the infeed motors and main band saw blade 20HP motor Recent epoxy paint Updated with modern electrical control panel with built in disconnect switch. The Resaw appears to be recently refurbished Always operated and stored inside More details , pictures and test run video available upon request. Doesn't require a saw dust pit to operate Price includes loading onto your truck. Can provide a delivered price upon request.
Equipment Location:Toledo, WA
Call for Price
Ferrari twin resaw, Kimwood Ferrari twin resaw bandsaw, used Ferrari band resaw, Kimwood Ferrari twin band re-saw, 42" vertical bandsaw, Ferrari double band saw resaw, Kimwood Ferrari resaw bandsaw, used Ferrari band resaw, bevel cutting band resaw, Kimwood Ferrari twin band re-saw, 42" vertical bandsaw, infeed can tilt for a bevel cutting up to 50 degrees inward or 30 degrees outward, feed speeds 40 to 400 fpm, Ferrari bandsaw Kimwood resaw, removed from operating service in June 2017, extra band saw wheels available, stored inside our warehouse, more photos and information available, video of dial indicator test available for top and bottom wheels, BELOW ARE SPECS FOR THE TWIN RESAW FROM THE MANUFACTURER ‘S (KIMWOOD) WEBSITE: BUYER WILL NEED TO VERIFY ALL INFORMATION WITH KIMWOOD CORP. Infeed Table can be tilted to 50 degrees inward or 30 degrees outward Capable of sawing jambs, headers, casings, and sidings in multiples with close tolerances Variable speed hydraulic feed rolls drive from 40 to 400 FPM. Harden tool steel knife edges on all the strain components Utilized anti-friction bearings Patented top and bottom saw guides Sniping eliminated due to the placement of feed rolls. Guides adjustable while machine is running. Rear saw is capable of moving forward 2 ½” or back 8” from the front saw or can be tilted back 20 degrees. Saw Specifications: 18 to 21 gauge with 18’ 6” to 20’ 6” maximum lengths
Equipment Location:Toledo, WA
$7,400
New York Blower fan Size 574DH •Series 20 GI Fan •Shop# M10845 100 •150HP motor, 460 volt, 1785 RPM •estimated 34,000 CFM @10" static pressure, buyer will need to verify from manufacture •Inlet vane damper •Round inlet size 33 inches •rectangle outlet size 32.5" X 26.5" •Overall measurement: Height 105", Length 143", Width 95" •prior use was pulling in clean air behind wood dust filter •fan was in service until October 2014 •Upon request we can take a video, and paper work of test run of fan and motor by an independent motor repair shop •Stored inside after we removed (Oct. 2014) it from prior location •Price includes loading on your truck, Estimated CFM and SP is available also
Equipment Location:Toledo, WA
$3,900
Siemens 300 HP direct coupler type electric motor •1790RPM •460 Volt •340 amps •Frame 449TS •Serial # 1-5113-39484-1-1 made in USA •Test ran and painted by independent motor shop, have paper work. stored inside •Call for more information or a freight rate 2 Reduced voltage starters also available(sold separately)
Equipment Location:Toledo, WA
$3,150
•Stainless steel fan (wheel and fan body) •Clean air type fan wheel (might be a backward curved?) •Inlet 25 1/2?, Outlet width 19? X 23 1/4? •wheel diameter 33? and width of wheel is 8? •no motor (used motor available) •Fan performance is only a guess- 5,000 to 26,000 CFM, 0 to 9 inches of static pressure •No tag is on the fan •Stored inside
Equipment Location:Toledo, WA
Call
Clarkes Pneu-Aire dust collector Clarkes model # 57-20, 200HP (Baldor motor) New York Blower main fan 38,000 CFM @21 sp. 48? diameter blow pipe clean air outlet 57 large filter bags Airlock size 16? diameter inlet/outlet 30HP purge fan Dust collection system was operating until April 2015 Disassembled and ready to deliver to your location. Additional YouTube videos before dismantling and inside of baghouse are available: https://youtu.be/wMpBC-2k5Qc
Equipment Location:Toledo, WA
Call
Heavy duty powered rotating platform •Industrial turntables •Platform size is 50" wide by 98" long •Large diameter ring gearElectric gear motor to rotate table topTables can be painted white •Top platform metal plate 3/8" thick •Platform frame is 6" X 6" square tube •Several platforms available •Call for a delivered price 1/2HP Sew-Eurodrive, 230/460volt The YouTube video shows one of the turn tables (painted white) manually rotating, we removed the gear box so we could use it manually
Equipment Location:Toledo, WA