Equipment For Sale

2006 Peterbilt Day Cab Cat C13 engine (475 hp) 13 speed Wetline 624,890 miles Engine has been rebuilt Runs and drives great

2019 PETERBUILT 389, 590,000mi., Cummins X15 Engine w/500HP, 18 spd trans., Pete Low Air Leaf! Will be polished out, New driver seat and windshields $75,000

1997 Peterbilt Sleeper 2.1 mil miles 13 speed reman tranny 3 years old 390 rears 63" bunk Cat 3406E 350k miles on engine since platinum rebuild by Cat Fiberglass front and rear fenders Both rear ends rebuilt including housings Roard ready Retiring PRICE REDUCED

2002 Peterbilt 377 Log Truck -3406 E certified rebuilt CAT with warranty -Reman transmission 18 speed -2 rebuilt rear ends -All new breaks -Good tires all the way around -2017 Rotobec elite loader

2000 Peterbilt 378 Quad Axle 475 Cat Engine 8LL Tranny Henderson 46 Full Lockers 20,400 Original Miles Nice Truck Pup trailer available

2019 PETERBUILT 389 650,000 mi., Cummins X15 Engine w/500HP, 18 spd. trans., Pete Low Air Leaf! Will be polished out, New driver seat and windshields $75,000

1981 Peterbuilt 359 -324,000 miles -CAT 3406B -15 speed transmission -Jake brake -Mack camel back -38k rears 12k front -Older truck so has its seeps but overall solid rig

2009 Peterbilt 365, C13 engine, 13 speed, 3.70 ratio, 305k miles, wet kit. $34,500

2023 PETERBILT TANDEM AXEL DUMP TRUCK 34,865 MILES CUMMINS ENGINE AUTOMATIC TRANNY STEEL BODY PINTLE WITH AIR TO THE REAR PLOW SPREADER TRUCK HAS NEVER BEEN USED TO PLOW WITH NO RUST PLOW,SPREADER,CONTROLS AND INSTALL WAS FOR $38,000 LIKE NEW CONDITION FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT WE CAN FINANCE REGISTRATION AND TAXES GRANITEHE.COM

158000 miles clean truck Paccar mx13 14,600 front end 46,000 rears Locking rear ends also available with a 2020 48’ deloupe tri log trailer for additional cost

2020 Peterbilt 567 Sleeper Semi Truck 228,000 miles 565 HP Cummins 1X15 18 speed manual trans 3.36 rears Double frame heavy spec 46,000 rears 13,200 steer 3 stage jake Wet line New clutch by Peterbilt 48" flat top sleeper

2014 Peterson 4300B -6,000 frame hours -Current hours on engine and rebuild 100(C18) -New rods and mains -New turbos -New pumps -Valves -Infeed floor and chains -6 new knives -New fans -Wiring -Tires are 90% brakes work

2014 Peterson 4300B Whole Tree Chipper, Caterpillar C-18 Engine, has 3,000 Original Hours and 6,000 Frame Hours New Wireless Remote, New Turbo, New Pumps, New Infeed Floor, New Chains, 6 Knife Chipper, New Rods on Engine, Completely Rebuilt Engine with 100 Hours, Completely gone through machine Ready to Chip. Weight 52,000 lb Length 35' 9" Width 11' 4" Height, 12' Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

765HP C18 engine, serviced, ready to go.

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

2016 Peterson Pacific 4710B Horizontal Grinder, Caterpillar C-27, 1050 HP, 9000 Hours, 90% Undercarriage, Wireless Remote Control, Ready for Work. Weight 79,000 lbs Length 36 ft 3 in Width 10 ft 9 in Height 11 ft 6 in Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

Remote control

Peterson 4800 Flail Debarker Wireless remote controlled Reman engine Runs and operates good

2018 Peterson 5710D -1,000 original hours -Owner used very few times -Belts are good -Tracks and Undercarriage are good Like new machine !!!!!

2005 Peterson 5410 Grinder -5800 hours -CAT 3412 Engine 1000H.P -Needs a discharge belt -New feed chains -New tip protectors