Equipment For Sale

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

Manufacturer’s Specification Model EG800A ELECTRO GLUE RADIO FREQUENCY EDGE GLUER Feeds Left to Right Curing Area: 36” deep by 96” long. Clamping Capacity: 41” deep by 96” long by 2” thick. Side Pressure::Applied by (16) 5” bore by 12” stroke air cylinders on 6” centers. Cylinders are NFPA Standard “Parker” Cylinders Top Pressure: Applied by (4) 3 1/4” bore by 18” stroke air cylinders. Cylinders are NFPA Standard “Parker” Cylinders Generator: A built in 30 kW. Radio Frequency generator cures approximately 3,000 square inches of glue line per minute. The generator is completely enclosed in aluminum housing. The generator also features a vacuum variable for improved efficiency and performance. Operators Control Panel: Includes adjustable cycle timer, necessary meters, indicator lights, control pushbuttons and a two hand, no-tie-down control system for closing the press. System Controls: The system is controlled by an Allen Bradley PLC. The system is equipped with a rotary disconnect that is mounted on the electrical panel access door. All PLC outputs and branch circuits are fuse protected. Safety: An electronic eye prevents closing of the press in the event any objects are inserted from the front. All access doors are interlocked to prevent use of the generator in the event any are open. A safety switch is used to prevent the use of the generator when the press is in the open position. Voltage: Installation: Quoted price includes the services of a Rosenquist technician to assist with the installation of the equipment and training of production and maintenance personnel. Included are all travel and living expenses. Delivery: Currently 12-14 Weeks INCLUDED OPTIONS Smart Cure: This feature utilizes the capabilities of the plc to monitor the cure rate of the adhesive and will automatically end the cure cycle once the adhesive is set. This will eliminate the need for the operator to calculate the amount of glue line and manually setting the RF cycle timer. The system is also equipped with the standard cycle timer. ????????? Automatic Power Control: Eliminates the need to adjust the power control manually. Eliminates human error associated with incorrect power settings. Slightly faster cure cycles will be realized. Recipe Control: This feature allows a specific recipe for a particular species or product to be stored in the PLC. The recipe control system will automatically set the “Edge Pressure”, “Smart Cure Settings”, Dwell Time” & “Power Level” for each recipe. A recipe is recalled by depressing one of the illuminated pushbutton located at the operators control console. Powered In-feed Table: provides a convenient workspace for the operator to compose a set of panels while the press is closed. Pusher is powered by an electric motor that is controlled by an inverter drive. Includes all necessary push buttons and controls. Out-Feed Table: A metal table mounted on the same angle as the press with an area of 96” long x 42” wide. ????

Rotex 6' x 16' Chip Shaving Screen

Rotex HICAP 2100 Chip Screen

7552 ROTOBEC GRAPPLE WORKS AS IT SHOULD, GOOD DEAL FOR THIS GRAPPLE

504 Continuous Rotator, Opens to 48"", Closes to 4". Price includes delivery to you"

NICE 4048HD cont turn grapple, tight, new turn motor

3/4 yard orange peel grapple, fully enclosed tines, opens to 86 1/2 inches, cylinder protectors Grapples from 5/8 to 3 cubic yards are available. Call Tim 800-467-0944

OPTIONAL VALVE (VOS) 3 FUNCTION HYD CONTROL OPTION CUSTOM LUGGING RGP 904 ROTATOR RGS750 BUNDLE INSTALLATION KIT & DIAGRAM

RPA4570R43 OPTIONAL VALVE (VOS) CUSTOM LUGGING RGP 1300 ROTATOR RGS750 BUNDLE INSTALLATION KIT & DIAGRAM

CUMMINS QSB 6.7 TIER 5 STAGE V (173HP) 32'6" BOOM BAR SAW/PULL THROUGH DELIMBER HYDRAULIC OPTIO CARRIER READY LESS MAIN VALVE AIR CONDITIONING AM/FM RADIO CB RADIO STANDARD BOOM LED LIGHTS STANDARD CAB LED LIGHTS ANCHOR KIT YOKE 12 ½" LADDER STANDARD THERMAL VALVE

CUMMINS QSB 6.7 TIER 5 STAGE V (173HP) 32'6" BOOM BAR SAW/PULL THROUGH DELIMBER HYDRAULIC OPTIO CARRIER READY LESS MAIN VALVE OPTION DEAD HEEL 3000LB COUNTERWIGHT AIR CONDITIONING AM/FM RADIO CB RADIO STANDARD BOOM LED LIGHTS STANDARD CAB LED LIGHTS HYDRAULIC TANK HEATER (110V) ANCHOR KIT YOKE 12 ½" LADDER VISCOUS CLUTCH FAN SUN SHADE STANDARD THERMAL VALVE OPTIONAL LED LIGHT (BACK OF CAB) 7" STABILIZER CYLINDERS OPTIONAL PRIORITY VALVE (SWING PRIORITY) OPTIONAL TRAILER STABILIZER CONTROL (FROM SCR) ROTOBEC 4552HD RT502 (S/N 219648-1-1) BIG JOHN TRAILER 142LT (S/N PF105285)

ROTOBEC 6007/RT222 (SN: 139522-6-1) M25 BOOM STABILIZERS HYDRAULIC PUMP HYDRUALIC OIL TANK

ROTOBEC 6007/RT222 (SN 135476-5-1) M25 BOOM STABILIZERS OIL COOLER HYDRAULIC PUMP HYDRAULIC OIL TANK

Clean structurally, dry, tight and operates properly.

504 Continuous Rotator, Opens to 52"", Closes to 4.5"

This grapple was taken off of a 2016 Deere 437E. All new pins and bushings. Cylinders inspected and have been packed. Grapple rotate is dry. Grapple is ready to go to work. Grapple was painted red based on logger feedback. Financing and delivery available.

Opens to 42 inches closes to 4 inches, other models available

5000 hours on grapple, rebuilt swivel. Excellent condition. Off Timberpro TF830