Equipment For Sale

BRANDT - KDN 630, ...Edgebander.0.4 - 8 mm (5/16") Edge cap., panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8"), and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function.Equipped with: -- Quick heat up glue system, w/glue tank for maintenance, and glue color change. -- Automatic magazine for strip & coil (large coil table, 800 mm dia. to accommodate large coils of 3 mm PVC stock), 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Signal infeed light to insure proper spacing between panels. -- Automatic height adjustment with top pressure beam for all workstations, equipped with digital height indicator.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°. -- (2) Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor) with insert knives for 3 mm PVC radius. -- Top & Bottom scraping for 2 - 6 mm radius, pneumatically controlled blow off nozzles; Top & Bottom buffing (0.25 HP - 1,400 RPM motors). -- End trim & flush trim stations with: HF Motors, electronic brakes; feed chain track speed of 46 FPM, 2 HP feed drive. Complete with: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link, and used tooling.

Great Condition Recently Fully Serviced Profile Scrapers and Surface Scrapers No Premill/No Buffers

BRANDT - F-13, ...Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL, and veneer edgings; up to 3 mm max. thickness. -- Manually operated; 1/2" - 2-1/4" panel thickness; 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each). -- Built-in air jet blowoff device; 31" x 48" table size; dual foot pedal control.NOTE: Intermittent fault in the Control Panel, which will require replacement.

BRANDT AMBITION 1110 (KDN 110) EDGEBANDER: -- Specifications:0.4 - 3 mm (1/8") Edge thickness cap.; 8 - 40 mm (0.3" - 1.57") panel thickness; 60 mm (2.3") min. panel width; 140 mm (5-1/2") min. length.Equipped with: -- Infeed fence: Adjustable; manual with digital indicator. -- Gluing System: Hot-melt; quick heat-up time; easy maintenance. -- Edge Magazine: Automatic for strip & coil stock; 3 mm PVC guillotine. -- Side Pressure Section: (1) Driven plus (2) idle rollers w/digital readout setting.Workstations: -- End Trimming Unit: Double-motor end trim; (2) x 1/2 HP - 12,000 RPM motors; chamfers 0° - 15°. -- Multi-Trimming Unit: Top/Bottom for flush/bevel/radius trimming; (3) quick setting positions; motors: (2) 1/2 HP - 12,000 RPM; with insert knives. -- Buffing Unit: Top/Bottom; (2) 1/2 HP motors. -- Scrapping Unit: Top/Bottom Scrapping UnitControls:LCD Display: Approx. 2 x 6" with soft keys for fast navigation and operator comfort. Complete with: -- Feed Speed: Fixed; 8MPM (26 FPM); 3 HP feed drive. - Sound enclosure and Scraper collection box. -- Actual Model is BRANDT AMBITION 1110 (KDN 110).

BRANDT KDF 110 (AMBITION 1110) EDGEBANDER WITH PRE-MILL0.4 - 3 mm (1/8") Edge thickness cap., 8 - 40 mm (0.3" - 1.57") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- In-Feed Fence, adjustable, manual with digital indicator. -- Pre-Milling Unit, (2) motor, (1) jump, counter rotating for the best possible glue joint. -- Gluing System, hot-melt, quick heat-up time and easy maintenance. -- Edge Magazine, automatic for strip & coil stock, 3 mm pvc guillotine, -- Side Pressure Section, (1) driven plus 2-idle roller w/digital readout setting.Workstations: -- End Trimming Unit, double motor end trim (2 x 0.5 HP - 12,000 RPM motors), chamfers 0° - 15°. -- Multi Trimming Unit, top/bottom for flush/bevel/radius trimming with (3) quick setting positions. Motors (2 x 0.5 HP - 12,000 RPM) with insert knives. -- Buffing Unit, top/bottom (2 x 0.5 HP) motors. -- NOTE: Open station at end; scraping unit could be addedControls:LCD Display, approx. 2 x 6" with soft-keys for fast navigation and operator comfort. Complete With: -- Feed Speed, fixed 8 m/Min (26 FPM), 3 HP feed drive. Sound enclosure and Scraper collection box.Actual Model: AMBITION 1110

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

BRANDT AMBITION 1200 (EDGEBANDER WPRE-MILL & CORNER ROUNDING): -- Specifications: Edge & Workpiece Capacity, 0.4 - 3 mm Edge cap., min. panel thickness 8 mm (0.3"), max. panel thickness 40 mm (1.57"), min. panel width 70 mm (2.75"). Min panel length: 140 mm (5.5")Line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all workstations. Auto in-feed stop to insure proper spacing between panels. Equipped with:Pre-Milling Station:(2) motors @ 0.75 kW (1.0 HP) ea., 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Gluing Section:Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, Pressure Section with (1) large drive plus (2) idle rollers "pneumatically controlled." Hot Melt granulate quick heat-up glue system. Workstations: End Trimming: 2 x 0.18 kW (1/4 HP), 12,000 RPM motors, THK guided, chamfers 0° - 15°. -- Flush/Bevel/Radius Trimming:2 x 0.55 kW (0.75 HP),12,000 RPM motors with insert knives for 3 mm PVC radius. cutter-heads, bevels 0° - 15°. -- Corner Rounding Station:1-Motor (4-corners) contour trim for profile corner rounding, 1 x 0.35 kW (0.5 HP), 12,000 RPM motor, with insert knivesFor 3 mm PVC radius w/digital read-out set-up and pneumatic change-over from thin to thick PVC edge tape. -- "Quick-Change" Profile Scraping Unit:Top & bottom for 2 - 3 mm radius, pneumatically controlled blow-off nozzles. -- Flat Scraping Unit:Top & bottom flat scraping units with copy wheels to remove residual glue squeeze-out.Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad.Production readiness displayed by traffic light indicator with ability to adjust units quickly thanks to direct access via ctrl keys. Intuitive, user-oriented navigation with a clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Complete With: &#9679 Trim stations have HF motors w/electronic brakes &#9679 Fixed feed chain track speed of 8 MPM (26 FPM) &#9679 2 HP feed drive &#9679 208/230/440/480v, 3ph Transformer &#9679Sound/Safety Enclosure &#9679 Adjustable Out-Rigger Support &#9679 Used tooling. -- Actual Model is BRANDT AMBITION 1200.

BRANDT KDN 650 C Edgebander; 6-Station Edgebander with 0.4 - 8 mm (5/16") Edge capacity. Specifications: -- Panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; -- Line control (NO limit switches) for workstation function. -- Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator. -- PC-16 Program Control with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; -- Signal infeed light to insure proper spacing between panels. Equipped with: -- Quick heat-up glue system (10 to 12 minutes). -- Automatic magazine for strip & coil stock (large coil table 800 mm diam. to accommodate large coils of 3 mm PVC), 3 mm PVC guillotine; -- (1) Drive plus (3) idle roll "pneumatically controlled" pressure sections. Workstations: -- End trim (1/3 HP - 12,000 RPM motors) chamfers 0° - 15°; -- Top & bottom flush trim, bevels 0° - 15°, (2) 1/2 HP - 12,000 RPM motors) with insert knives. -- 2-Motor (4-corners) contour trim for profile corner rounding (2) 1/2 HP - 12,000 RPM motors), with insert knives for 3 mm PVC radius. -- Top & bottom scraping for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. -- Last Station: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Feed chain track speed 42 FPM, 2 HP feed drive. Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling.

BRANDT OPTIMAT KDN 650 C Edgebander, with Corner Rounding, Pre-Melt, & 8,654 Hrs. (As of 6/2/22) Specifications: -- Edgebanding thickness 0.4 - 8 mm (0.02" - 0.31"). -- Panel thickness 8 - 55 mm (0.31" - 2.17"), Min. panel width 65 mm (2.56"), Min. panel length 160 mm (6.30"). -- Feed speeds 11/14 FPM (36/46 FPM). -- Working height 950 mm (37.40").Equipped with: -- 32-1/2" Dia. Coil table. -- Automatic magazine. -- 3 mm (0.12") Guillotine. -- "Quick-Melt" Hot melt glue unit, with Heat-up time: Approx. 12 min., Pre-melt hopper feed, Quick-change hopper & tank for color changes, Reversible glue applicator roller rotation, & Retractable glue roller. -- Pressure section, with (1) Large driven & (3) Small pneumatically-controlled idler rolls. -- "POWER CONTROL PC 20+" Control, with 600 MHz, 256 MB RAM, USB Port, 1 GB Flash card, Internal modem for remote diagnostic access link, & 12" TFT Flat screen monitor. -- Line control (no limit switches) for workstation functions. -- Feed chain, with 2.2 kW (3 HP) Feed motor & Automatic chain track lubrication. -- Digital height indicator. -- Sound enclosure.Workstations: -- Front & rear end trimming unit, with (2) 0.35 kW (1/2 HP) - 12,000 RPM High frequency motors, 0° - 15° Chamfer, & Programmable pneumatic control for straight or chamfer trimming. -- Top & bottom flush trimming unit, with (2) 0.55 kW (3/4 HP) - 11,300 RPM High frequency motors, 0° - 25° Swivel, & Combination straight/radius cutters. -- Corner rounding unit, with (2) 0.35 kW (1/2 HP) - 10,940 RPM High frequency motors & 3 mm (0.12") Radius insert cutters. -- Top & Bottom Profile scraping unit, with Vertical & Horizontal tracing. -- Top & bottom buffing unit, with (2) 1/4 HP - 1,400 RPM Motors and Vertical & Horizontal tilt.

BRANDT AMBITION 1440 (KDF-440 C) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 (KDF 440 C).

BRANDT KDF 660 Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.

BRANDT AMBITION 1440 FC (KDF-440 FC) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Heated Adjustable Infeed Fence: Radiant Heated with Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for Top & Bottom, Leading & Trailing edges & Corner Rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 FC (KDF 440 FC).

BRANDT KDF 440 C (AMBITION 1440 FC) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) & 3,359 Hrs.Specifications: -- Edge & Workpiece Capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") Panel thickness, 160 mm (6.30") Min. panel length, 70 mm (2.76") Min. panel width.Equipped with: -- Adjustable Infeed Fence: Motorized adjustment with 0.049 kW (0.07 HP) Motor. -- Joint Trimming/Pre-Milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, Left-Hand & Right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting, 0.4 - 8 mm (0.016" - 0.31") Strip thickness, 3 mm (0.12") PVC Max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kg/Hr. (13 - 22 Lbs./Hr.) Melting capacity (Depending on glue type). -- Workpiece Preheating Unit -- Pressure Zone: (1) Driven & (2) Idle Rollers, Timed pneumatic pressure controlled, Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM), 11 MPM (36 FPM) with Contour trimming. -- BRANDT "POWERTOUCH" Control: With 21" HD LCD Touchscreen monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors, with 0° - 15° Automatic chamfer, Pneumatic adjustment & Activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt, with Horizontal & Vertical Tracing wheels, Brushless multi-axis servo motors for positioning of work-unit & horizontal copy wheels for quick changeover, with (3) Positioning options: Profile 1, Profile 2 & Flush trimming. -- Multi-Functional Trimming Unit: (2) 0.4 kW (1/2 HP) 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Either radius or chamfer cutters can be mounted, 3 mm (0.12") Max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"), Servo control positioning of vertical & horizontal copy wheels, PVC Scrape collection box, Pneumatic adjustment using "POWERTOUCH" control, Pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface, with Floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) 2,750 RPM Motors.Complete with: -- Motorized, programmable hold-down pressure beam with 0.12 kW (0.16 HP) Motor, 1.5 kW (2 HP) Feed motor, 32" Diameter Coil table, Padded sound enclosure.NOTE: CPU needs to be replaced.

Brandt KDF 440C Edgebander

BRANDT - "KD-68", ...Edgebander1/4" (6 mm) Edge thickness cap. (will even do 8 mm max.); max. edgebanding height: 60 mm (2-3/8"); min. workpiece length: 160 mm; width: 70 mm (2-3/4").Equipped with: -- Quick Melt Glue System with: (10) Min heat up time and reversible glue roller. -- Automatic magazine for strip & coil stock; 3 mm PVC guillotine; 3-roller Pressure Section.Workstations: -- Double motor end trim on uni-slide: 0.33 HP - 14,400 RPM; chamfers 0° - 15°. -- Top & Bottom flush/bevel & radius trim; bevels 0° - 15°; 1/2 HP - 14,400 RPM motor ea.; w/SIKO digital readouts. -- Top & Bottom scraping for standard or 3 mm PVC edging; air jet blowoff; SIKO digital readouts. -- Top & Bottom buffing: 1/2 HP - 1,650 RPM; adjusts 0° - 40°. -- Feed chain feed speed: 36 FPM.Complete with: Electronic motor brakes on both trimmers; padded sound enclosure; eye level height swivel control panel w/fault sensor control; adjustable outboard panel support track; frequency converter; used tooling.

Brandt KF 76F Edgebander: Pre-milling, top/bottom trim, buffing, extra glue pot

--make offer--requires repair-- BRANDT KDF 440 C/AMBITION 1440 FC EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) & 3,359 Hrs. Specifications: Edge & Workpiece Capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") Panel thickness, 160 mm (6.30") Min. panel length, 70 mm (2.76") Min. panel width. Equipped with: Adjustable Infeed Fence: Motorized adjustment with 0.049 kW (0.07 HP) Motor. Joint Trimming/Pre-Milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, Left-Hand & Right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting, 0.4 - 8 mm (0.016" - 0.31") Strip thickness, 3 mm (0.12") PVC Max. coil thickness. Hot Melt Glue Application Unit: 6 - 10 kg/Hr. (13 - 22 Lbs./Hr.) Melting capacity (Depending on glue type). Workpiece Preheating Unit Pressure Zone: (1) Driven & (2) Idle Rollers, Timed pneumatic pressure controlled, Servo motor positioning for programmable edge thickness changeover. Feed Speeds: 8 - 14 MPM (27 - 45 FPM), 11 MPM (36 FPM) with Contour trimming. BRANDT "POWERTOUCH" Control: With 21" HD LCD Touchscreen monitor. Workstations: Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors, with 0° - 15° Automatic chamfer, Pneumatic adjustment & Activation/deactivation of edging material overhang using "POWERTOUCH" control. Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt, with Horizontal & Vertical Tracing wheels, Brushless multi-axis servo motors for positioning of work-unit & horizontal copy wheels for quick changeover, with (3) Positioning options: Profile 1, Profile 2 & Flush trimming. Multi-Functional Trimming Unit: (2) 0.4 kW (1/2 HP) 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Either radius or chamfer cutters can be mounted, 3 mm (0.12") Max. edge thickness. Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"), Servo control positioning of vertical & horizontal copy wheels, PVC Scrape collection box, Pneumatic adjustment using "POWERTOUCH" control, Pneumatic disengagement. Top & Bottom Glue Scraping Unit: Flush on panel surface, with Floating insert knives. Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) 2,750 RPM Motors. Complete with: Motorized, programmable hold-down pressure beam with 0.12 kW (0.16 HP) Motor, 1.5 kW (2 HP) Feed motor, 32" Diameter Coil table, Padded sound enclosure. NOTE: CPU needs to be replaced. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.