Equipment For Sale

1992 Baker 6 Head Resaw Six-Head "C" Saw 1 needs a spindle and wheel replacement. Approximately 8,320 Hours Serial Number 92-379 6 Motors (30) HP (37) Amps Mechanical Drive

Baker Model D Resaw 16" Wide capacity Heavy Duty Return Conveyor

Baker Furnace Dry Kiln 110volt 3 phase Excellent condition

2024 Model Baker II “PAQ” with 20hp motors, 5hp variable speed hydraulic drive system, extend infeed with hopper attachment, adjustable hold over fence, & powered infeed hold down. The saw is electric complete with 480 voltage, panel, pedestal mounted start and stop stations, & hour meter. $24,000.00

Baker PAQ Resaw Good Working Condition

2 - Baker Stacking Racks available

2 strand transfer deck, 28" wide x 14' long, #80 roller chain, no drive, good condition

Baker Furnace Inc Dry Kiln 3 phase 110V

Dry Kilns (cream), Conventional Heating System, 600,000 BTU Propane, single phase, 120V control voltage, 3 phase 208V motor voltage, open volume: 672 cubic feet, max operating temperature: 500F, owners manual included, excellent condition, 2 units available

Baker Furnace Inc Kiln 110V 3 Phase

Complete Drying System, 10.5’ x 32’ Triple Pass Drum Dryer, Wood Or Gas Dryer, 300 HP Fan & Cyclone, Excellent Condition!

BALEMASTER - HD-60, ...Closed Door BalerSpecifications: -- Main motor: 20 HP -- 8" Cylinder -- Bale size 48" x 30" x 60" -- Feed opening: 57" x 35"Equipped with: -- Touchscreen controls with ALLEN BRADLEY - Micrologix, ... PLC 7" QuickPanel -- Electrical disconnect switch installed on Baler -- Ground feed oversized hopper -- Totally enclosed fan cooled (TEFC) High-Efficiency motor -- Windowed Feed Chute Door with control circuit Interrupter (Limit Switch) -- Shear Blade -- Cycling eye mounted in the frame -- Low Oil Level & Hot Oil Temperature Sensors

BALEMASTER - 48 X 72, ...Horizontal Closed Door Baler -- Designed for baling of whole or flattened corrugated boxes. -- Large feed opening to accommodate feed of larger material. -- Large 48" x 36" x 72" bale; weighs up to 1,700 pounds. -- Perfect for a Qarehouse application. -- 25 HP Moroe

BALEMASTER - 4550G-10: Auto-Tie Horizontal BalerSpecifications: --27"; x 40"; Opening. -- 50 HP. -- 10"; Cylinder. -- 30"; x 40"; x Variable Bale.

BALEMASTER E-1290 Auto-Tie Horizontal Baler with AMERISHRED AMS-7500 Shredder/Conveyor/TipperBaler Specifications: -- Cylinder: 10" -- Bale size: 36" x 40" x variable -- Motor: 75 HPShredder Specifications: -- Cut: 5/8" -- Motor: 75 HPSystem equipped with: -- Enduraveyor Baler Feed Conveyor -- Discharge Conveyor -- Metering Feed Conveyor -- Cart Tipper

BALEMASTER - EO-650: Horizontal Auto-Tie Baler Specifications: • 25 HP Motor.• 8"; Main Cylinder.• Hopper Opening: 46";x 50";.• Bale Size: 48"; x 30"; x (variable).• Main Ram Face Pressure: 75 PSI.• System Pressure: 2,000 PSI.• Total Compression Force: 100,500 Lbs.

BALEMASTER 772 AO WIDE MOUTH HORIZONTAL BALER -- 25 HP motor -- Dual door cylinder -- Bale size 48" W x 26" H x 48" L -- Feed chute cross section 46" W x 48" L -- Air to Oil cooler included -- Number of bale ties 5 -- Loaded on your truck

BALEMASTER - 760AO, ...Horizontal Closed Door BalerSpecifications: -- Cylinders: (2) 6" -- Feed opening: 60" x 40" -- Bale size: 48" x 72" x 34" -- Main motor: 25 HPEquipped with: -- (4) Wire single-loop bale ties -- Heat exchanger -- Photo-eyeNote: Dog ear springs need to be replaced and a small leak by the motor; otherwise, in great condition.

BALEMASTER 4025G-8 Auto-Tie Horizontal BalerSpecifications: -- Cylinder: 8" -- Main motor: 25 HP -- Feed opening: 32" x 27" -- Bale size: 30" x 36" x VariableEquipped with: -- 5 Wire TieNOTE: Shear not included.

BALESTRINI 2 CAP Mortiser --Automatically mortises or bores round holes in chairs or case good --Specifications -- Twin tables with pneumatic holddown clamps, (1) on each side eliminating dead cycle time, 19" long tables tilt left or right 0ø to 20ø. --Equipped with & Features -- 3 HP - 9,000 RPM Spindle motor and 1 HP oscillation motor. -- Spindles are mounted on prismatic guides with adjustable bronze gibs and move by rack & pinion, -- (120) to (240) oscillations/Min; 4-23/32" max. oscillation length, -- 3-1/8" max. depth, 7/8" max. bit dia., 13 mm spindle collet dia.