Equipment For Sale

EXTREMA DCF-05 Bag Filter. -- Features a 16" inlet; unit has (5) sections, (5) 1 micron filter bags with (5) plastic collection bags, rings, clamps and legs. -- Modular design enables additional sections to be added or removed. -- Excellent addition to the "DCY Typhoon" Dust Collector!

EXTREMA DCF-327 Baghouse Dust Collector.Features a 16" inlet; unit has (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) Micron filter. -- For indoor use. (Enclosed outdoor unit available). -- Excellent addition to the "DCY Typhoon" Dust Collector

EXTREMA DCF-327E Baghouse Dust Collector.Features a 16" inlet; unit has (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) Micron filter. -- Available for outdoor & indoor use; unit is enclosed. -- Excellent addition to the "DCY Typhoon" Dust Collector; ...ask us why!

Extrema EP-216 16" Double Side Planer

Manufacturers Specification - ? [Specifications](https://extremausa.com/product/magnum-xp-series-25-double-sided-planer/#tab-test_tab) Horsepower: 40 / 30 HPVoltage: 230V / 460VPhase(s): 3 PHWidth: 25"Top Motor: 40 HPBottom Motor: 30 HPElevation Motor: 2 HPFeed Motor: 5 HPMax Thickness: 8"Min Thickness: 3/8"Min Stock Length: 16"Cutterhead RPM: 6000Top Cutter Access: Super SlideBottom Cutter Access: Super SlideDisc Brakes: YesFeed System: CarpetDrive System: ShaftFeed Speed: 20-110 ft/minCFM Requirements: 3000AMPS (220V/440V): 188 / 94Weight: 9300 lbs

EZ CAR - (Used) Model A: Car Crusher Approx: 6,200 hours.New in: 1988.System Pressure: 2,500 PSI.Port Reliefs set at: 2,650 PSI.Cylinders: 10" Bore.Travel: 78".Shaft: 4" rod.OpeningSize: 20" x 8'-1" x 7'-7".OverallWeight: 61,000 Lbs.Length: 43'-1/4."Travel & operating height: 13'-1/4'.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Parting Out Fabtek 153 with 4 Roller Head, Lots of Good Parts

Fabtek 546B Early 2000s Approx 24k hours Deere 6068 engine Bogie tires are new Front tires at 20% Pins and bushings are good Was ran through shop about 6k hours ago Valve seals weep a little when its cold Runs and operates good

Fabtech 546c log forwarder -engine been rebuilt -new joysticks -most cylinders have been repacked -brand new center section -hydraulic control valve was rebuilt -new log Bunks brand new LED lights -all new window seals with brand new lexan -new hydraulic hoses -new seat -John Deere power Tech 6 cylinder

1999 FABTEK 546B 8 WHEELED DOUBLE BUNK FORWARDER 6 CYL DEERE POWERSHIFT EXTENDABOOM BYPASS BUCKET JOYSTICKS 700 RUBBER

2000 FABTEK 346B DOUBLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS SQUUIRT BOOM

1998 FABTEK 344B SINGLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS BYPASS BUCKET ROTATER 23.1-26 RUBBER

Fabtek four roller processing head in decent condition. Head does come with computer.

THESE ARE BRAND NEW FABRICATED BUNKS FOR FABTEK FORWARDERS 2000 DOLLARS EACH

THESE ARE BRAND NEW FABRICATED STAKES FOR FABTEK FORWARDER THESE ARE 2300 EACH

2006 Fabtek 153 Processor, Equipped with a Fabtek (4) Roller Processor Head, Engine Has 6,100 Hours, was Remaned, Frame Hours 15,800, Enclosed Cab with Heat and Air Conditioning, Undercarriage is 80%, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2001 Fabtek FT133 Track Processer 18,300 hours Four roller head Runs and works well, $49,900

2001 Fabtek FT133, both Knife Cylinders repacked, roller cylinder repacked , main lift cylinder repacked, double grouser style 22.5 " pads, fixed 4 roller Fabtek Processing head, nice machine for the year, and has been well taken care of, $49,500

2002 Fabtek FT153 Track Processor 18,247 hours Good U/C Four roller head Good running condition, $49,900