Equipment For Sale

CEMCO 1237 DUAL HEAD WIDE BELT SANDER2-Head, 36" cap. - 1st Head: Rubber covered contact roll, 20 HP motor; 2nd Head: Finishing platen, 15HP motor; 37" x 75" abrasive belts with air tensioning. -- Variable speed conveyor feed, 15 - 60 FPM, 0" - 6" thickness cap., infeed & outfeed rubber covered pinch rollers. -- Equipped with: Motor load meters, infeed conveyor extension, air disc brakes on sanding heads, emergency operator stop bar, and dust hoods. Actual model # "1237-SE".Seller recently upgrades to a 3-Head 52" wide Sander and this one is no longer needed

Cemco SVB 120 Boring Machine 113" x 22" Boring area (14) 1.5 HP 1800 RPM motors driving (14) spindles 121" x 30.5" Table size (4) Spring loaded hold downs

CEMCO 2000 Wide Belt Drum Sander, Single Head. --Specifications: Lightly used. Only 2180 Hours. -- Belt Size is 37" X 75"; 20 HP main motor,.1.5" top roller plus 2- 5" bottom rollers. One steel 1 rubber covered. -- Thickness is from 0" - 6". No Platen. Variable speed feed. Emergency brake. good. 4-1/2" dust port. -- Note: This machine was replaced 12 years ago with a triple head Cemco. Stored in a dry warehouse since then. Ran well until we unplugged it. All Cemco equipment is of commercial quality. This sander is a workhorse.

CEMCO - 4000, ...2-Head Wide Belt Sander38" Width cap. - Drum, Platen configuration.Head Configuration:1st Head: 40 HP -1,780 RPM rubber contact drum head.2nd Head: 30 HP - 1,775 RPM platen style head.Specifications: -- 3 HP 230/460/60/3 Feed motor with TOSHIBA VFD controls. -- 15 - 60 FPM Conveyor feed speed . -- 30 HP - 3,525 RPM Vacuum blower. -- Vacuum type rubber conveyor feed belt. -- Push button controls and amp meters. -- Electric ProScale digital thickness readout. -- YASKAWA Varispeed F7.Equipped with & Features: -- VFD abrasive belt drive system. -- Outfeed workpiece dust cleaning enclosure.Includes: Replacement abrasive belts and belt racks.

Cemco 2000 Wide Belt Fair/good condition. It starts and runs until we unplugged it 12 years ago Belt size 37 x 75 2004 Single head 1- 5” roller top, 2 - 5” rollers bottom, 1 rubber covered, 1 steel. No platen Thickness ¼” – 6” 2179 hours on machine 230 V, 60 CY, 3 PH Variable speed feed 20 HP motor Emergency Brake

CEMCO SBV-120 Vertical Boring MachineSpecifications: -- 113" x 22" boring area Capacity, (14) 1.5 HP - 1,800 RPM motors driving (14) spindles, on/off switch controls for all motors -- Spindle nose with chuck 5/65" - 1/2" capacity -- 121" x 30.5" table size, (4) Spring loaded hold downs, -- 6" Spindle stroke adjustment with min. of 4" to max. of 10" between spindle nose and tabletop. -- Spindle assemblies advance hydraulically at 0 - 30 strokes/Min with single or continuous stroke -- 2 HP hydraulic feed pump w/variable speed control.Also included: -- 4 CHIP BLOW OFFS WITH INDIVIDUAL ON/OFF POSITIONS -- INSTRUCTION MANUAL/PARTS LIST -- DRILLING SAFETY GUARDS -- EMERGENGY STOP CABLE AND EMERGENCY STOP BUTTONFLOOR SPACE FOOT PRINT: 48: X 121"

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,Equipped With:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single cycle & continuous automatic modes;2 HP hydraulic feed pump, 12-gal. hydraulic pump system;Note: Riggers are required for loading

(14) spindles with 1-1/2 hp motors on each. On/off switch for each motor. chucks adjust to grip up to 1/2” bit stroke adjustable from 4” to 10” 121” x 39-1/2” table with (4) hold downs Adjustable speed hydraulic feed 230 volt 3 phase

- Width capacity 53”. Drum, Drum, Combination Head (see sander specs - Head 1: Rubber covered contact roll, 10” dia, 65 shore adjustable with dial - Head 2: Rubber covered contact roll, 10” dia, 65 shore adjustable w/dial - Head 3: Combination head, (2) 5-1/2” finishing drums w/platen - 440 V, 60 cy, 3 Phase - Year 2000, Good Condition - Warehoused after plant shut down factory in 2013 - Have manuals /spec sheets - Machine weighs app 6000#’s. - Buyer must pay for riggers to load onto truck. (our forklifts can’t pick it up)

CEMCO 3 Head Industrial Sander. Running when removed from location.

2003 CENTAURO TA-F-EC AUTOMATIC HYDRAULIC COPY

2004 CENTAURO TA-F-2000 AUTOMATIC HYDRAULIC COPY LATHE

2004 CENTAURO TA-F-2000 AUTOMATIC HYDRAULIC COPY LATHE

CENTAURO AG-125 Tool Grinding Machine for V-Type Gouges. -- Tabletop design saves space. -- Works with most sizes of V-gouges. -- Optional standing base $414.00. -- Diamond stone cutting wheels, ordered separately, price $636.00 each. -- Please specify the required voltage and lathe model when ordering wheels.

CENTAURO TC-1200 Copy Lathe;47-1/4" Max. between centers. -- 4-3/4" Height of centers over bed. -- Max. copy dia. 6" (4-1/8"). -- Max. dia. permitted by traveling steady 3-1/2" (2-1/2"). -- 4 HP main motor, 900 - 1,500 - 2,200 & 3,540 RPM spindle speeds. -- 1 HP hydraulic variable speed carriage with tool post and revolving steady rest. -- (2) Independent gouges working in conjunction with the traveling steady rest. -- Variable speed hydraulic saddle movement. Standard Equipment & Specs: -- Drive center with (2) interchangeable heads 1" and 1-3/4". -- Tailstock revolving center 1/2". -- Traveling steady rest max. 3-1/2" (square 2-1/2" x 2-1/2") with reduction bushing. -- (2) Vertical Tantung gouges, radius 1.2 mm and (1) precutting tool. -- Work-piece centering device. -- Tool support rest for hand turning. -- (2) Dust extraction ports 4" dia. -- Motor protection switch. -- Emergency push button. -- Front sliding safety guard. -- Standard: Service tool kit and Abrasive stone for cutting edge dressing.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with two copier heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and revolving steady rest attachment; 3-1/2" max. square part size with revolving steady rest, unit, 5.8" stroke of copying unit. 19-5/8" max. length for manual turning. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. -- Includes: Drive center, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center. -- Note this machine has no top Back Knife for plunging with form tool. -- Machine manual included.

CENTAURO T5-1600 Hydraulic Copy Lathe with (2) top plunging knives; Specifications: -- 63" (1,600 mm) Max. between centers, 4/5.5 HP main motor, two speed selector switch, 900 - 1,500 - 1,800 - 2,250 - 3,000 and 4,500 RPM spindle speeds. -- 1 HP Hydraulic power pack for variable speed carriage 0 - 19 FPM carriage; return speed 24 FPM, hydraulic tailstock with Pressure Reducing Valve (PRV) for fine control of pressure, especially helpful for small and/or slender turnings. Equipped with: -- (2) Independent copying units, (1) for roughing and (1) for finish cutting. 1st, 2nd pass & auto feature with 2nd pass active it will cut the pattern 2 times automatically and sequence the tools between cuts. -- Revolving steady rest, max. dia. 140/100 mm square ( 5.5"/3.9"), and for max. dia. 90/65 mm max. square billet size. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. Includes: -- (2) rear-top plunging slides manually operated with knives for making dowel ends; 45/26 mm drive center for headstock and 12 mm center for tailstock, (2) V-type gouges with 0.6 & 3.5 mm cut radii.Features: Centauro AG-125 Knife Sharpener.NOTE: Ex-Factory handles import/export to just about any country in the world.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with (2) Copier Heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and attachment for revolving steady rest; 3-1/2" max. square part size with revolving steady rest, 5" max. with copying unit, 5.8" stroke of copying unit. -- Capacity: 19-5/8" Max. length for manual turning. 9.8" (250 mm) Max copy dia., 6.8" (175 mm) max. square section without steady rest. -- Includes: Drive center with, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center.Note this machine has no top Back Knife for plunging with a form tool.

Extremely well-built Edge Sander with 5 HP - 1,200 RPM TEFC Motor. -- (2) 11" x 60" Cast iron platens. -- 10" x 172" Abrasive belt size. -- 0.5 HP oscillation motor to produce (150) oscillations/Min with 1/2" movement. -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table. -- All tables with 30° tilt up & 45° down. -- 5" Vertical table travel, 5" lateral side table travel and 4-1/2" lateral end table travel. -- Convenient hand wheel adjustment. -- Large 10" dia. x 10-1/2" face direct drive pulley with 4-1/2" dia. x 10-1/2" idle pulley for a huge sanding surface. -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

Nice CF Nielson BP5500 Press. The plant shut down in 2014. The machine was run again for a test in 2016 and everything was in good working condition. They have the dies and pistons to make round and octogonal logs. - Briquetting press CF Nielsen BP5500 - Dies to make 3’’ round logs and 2½’’ octogonal logs - Lignin dosing system - Water pump to add water if material too dry - Home-made automatic speed adjustment with encoder. - Briquette breaker from CF Nielsen at the end of the cooling line - Home-made flying saw with lenght asjustment at the end of the cooling line too with capability to switch from the saw to the breaker. - Can run up to 1200kg (even 1400kg I think) per hour depending on material and briquette shape - Cooling line can be opened to make pucks also. - 575V AC motors - Installed in 2008 - 10,865 hours