Equipment For Sale

Baker Furnace Dry Kiln 110volt 3 phase Excellent condition

Baker Furnace Dry Kiln 110volt 3 phase Excellent condition

Baker 6-head resaw, electric drive, good working condition

Baker 4hd Bandsaw with complete run around. Located in WI. #C952

Baker A single Head Bandsaw with 18hp Kohler motor #00899

2013 Baker M4I DeDuster with hopper infeed and variable speed drive and three 2hp brush heads. Electric complete with 480 voltage, panel, and pedestal mounted start and stop station. $6,500.00

The Baker M4i DeDuster has been designed to be a super-high-performance dust removal machine that will accept and remove sawdust from the highest production multi-head horizontal band resaw today. The M4i DeDuster can operate at over 700 feet per minute! Boards drop into the M4i DeDuster hopper. The hopper’s height adjustment (for the amount of lumber), indexable stops (for the length of the lumber), and adjustable fence (for the width of the lumber) allow you to set it up for the most efficient operation. This virtually eliminates jam-ups. The hopper’s variable-speed conveyor sends the lumber through the M4i DeDuster chamber one piece at a time. The rear height adjustment of the conveyor can be adjusted from a minimum of 24" and up to 34" maximum. Inside the M4i DeDuster chamber, high-speed brushes clean all four sides of the boards. The independently powered brushes are fully adjustable for longer brush life. The specially designed chamber maximizes air flow, directing the dust out the dust chamber instead of back onto the boards. The entire side of the chamber easily opens for full open accessibility. The Baker M4i DeDuster comes with its own electrical panel and a stand-mounted, remote start/stop control station.

This is a slightly used 2022 model 26” air activated chop saw with a 15hp motor wired for 480 voltage. It comes complete with the electric panel and controls. It has a 10’ idler infeed roll case with fence and a 5’ idler outfeed with a 48” stop bar and 4 manual stops.

Baker Furnace Inc Dry Kiln 3 phase 110V

Dry Kilns (cream), Conventional Heating System, 600,000 BTU Propane, single phase, 120V control voltage, 3 phase 208V motor voltage, open volume: 672 cubic feet, max operating temperature: 500F, owners manual included, excellent condition, 2 units available

Baker Furnace Inc Kiln 110V 3 Phase

Complete Drying System, 10.5’ x 32’ Triple Pass Drum Dryer, Wood Or Gas Dryer, 300 HP Fan & Cyclone, Excellent Condition!

BALEMASTER E-1290 Auto-Tie Horizontal Baler with AMERISHRED AMS-7500 Shredder/Conveyor/TipperBaler Specifications: -- Cylinder: 10" -- Bale size: 36" x 40" x variable -- Motor: 75 HPShredder Specifications: -- Cut: 5/8" -- Motor: 75 HPSystem equipped with: -- Enduraveyor Baler Feed Conveyor -- Discharge Conveyor -- Metering Feed Conveyor -- Cart Tipper

BALEMASTER - 48 X 72, ...Horizontal Closed Door Baler -- Designed for baling of whole or flattened corrugated boxes. -- Large feed opening to accommodate feed of larger material. -- Large 48" x 36" x 72" bale; weighs up to 1,700 pounds. -- Perfect for a Qarehouse application. -- 25 HP Moroe

BALEMASTER - 4550G-10: Auto-Tie Horizontal BalerSpecifications: --27"; x 40"; Opening. -- 50 HP. -- 10"; Cylinder. -- 30"; x 40"; x Variable Bale.

BALEMASTER - EO-650: Horizontal Auto-Tie Baler Specifications: • 25 HP Motor.• 8"; Main Cylinder.• Hopper Opening: 46";x 50";.• Bale Size: 48"; x 30"; x (variable).• Main Ram Face Pressure: 75 PSI.• System Pressure: 2,000 PSI.• Total Compression Force: 100,500 Lbs.

BALESTRINI MINI C 2500 DOUBLE SIDED TEMPLATE PROFILE SHAPERSpecifications: -- (2) Offset shaping heads with 10 HP (7.5 kW), 230/460 volt three phase drives. (1 each side) -- Maximum reciprocating length 98" (2500 mm). -- Maximum height 7" (180 mm). -- Maximum width between spindles 8", and shaping heads are staggered for full end rounding. -- 1¼"; Diameter work arbors with 7″ under the nut capacity, and Spindle speed of 8400 RPM -- Hydraulic stroke of 9-3/4″ wide x 110″ long tee slotted work table, with feed speeds of 3 - 49 feet per minute (1-15 m/Min.) powered by 3 HP, 230/460 volt three phase hydraulic pump -- Overhead beam clamp bar with (4) adjustable clamps. -- Push button operator control station.

BALESTRINI - "MICRON": Slot MortiserSpecifications -- Dual Spindle System (1) Each side with: Tables and overhead holddown; 3 HP - 9,000 RPM spindles; (60 - 350) oscillations/Min; 18 mm collet dia. -- Capacity: 4-23/32" (120 mm) Max. length of slot; 3-1/8" (80 mm) max. slot depth; 1-3/16" (30 mm) max. slot thickness.Hourly production rate: (500 - 800) Slots.

BALESTRINI 2 CAP Mortiser --Automatically mortises or bores round holes in chairs or case good --Specifications -- Twin tables with pneumatic holddown clamps, (1) on each side eliminating dead cycle time, 19" long tables tilt left or right 0ø to 20ø. --Equipped with & Features -- 3 HP - 9,000 RPM Spindle motor and 1 HP oscillation motor. -- Spindles are mounted on prismatic guides with adjustable bronze gibs and move by rack & pinion, -- (120) to (240) oscillations/Min; 4-23/32" max. oscillation length, -- 3-1/8" max. depth, 7/8" max. bit dia., 13 mm spindle collet dia.

Balestrini "MICRON" Slot Mortiser:Sprcifications -- Dual spindle system, (1) each side with tables and overhead holddown, 3 HP - 9,000 RPM spindles, (60 - 350) oscillations/Min, 18 mm collet dia. -- Capacity: 4-23/32" (120 mm) Max. length of slot, 3-1/8" (80 mm) max. slot depth, 1-3/16" (30 mm) max. slot thickness. - Hourly production rate of (500 - 800) slots.