Equipment For Sale

CANTEK - GT635ARD-16 25″ Double Surface Planer25″ Wide x 16″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external handwheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 16″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK - GT635ARD-8 25″ Double Surface Planer25″ Wide x 8″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external hand wheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 8″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK - C 12 RS, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2". -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- Features: 1-Piece cast iron chain with a diamond cut surface for positive material feeding.Total amperage is 21.5 and the gross weight approx. 2,530 Lbs.

CANTEK GT610HI CARDAN SHAFT DRIVE DOUBLE SURFACE PLANERSpecifications: -- Max. working width 24" (610 mm). -- Max. working thickness 8" (200 mm). -- Min. working thickness 5/16″ (8 mm). -- Min. working length 12" (300 mm). -- Cutterhead RPM 5000 RPMCutterhead diameter 5.3" (135 mm). -- Feed speed 30-98 FPM 10 – 30 m/min. -- Top cutterhead motor 40 HP. -- Bottom cutterhead motor 30 HP. -- Feed motor 5 HP. -- Table Rolls 7 (3) driven. -- Opening hoist motor 1 HP. Machine dimensions: (LxWxH) 112"; x 67"; x 67"; 2830x1700x1700mm . Machine weight 8800 Lbs 4000 kgsShipping weight 9240 lbs 4200 kgs. -- Shipping dimensions (LxWxH) 115"; x 75"; x 75"; 2900 x 1900 x 1900mmMachine electrics (Standard) 460/3/60 = 110 amps (Other voltages on request, factory order)Key Advantages• Cast iron machine frame for superior vibration damping resulting in a long machine & bearing life.• Chrome-plated tables and top and bottom for maximum wear resistance.• Cutterheads are mounted in precision ABEC 7 RHP bearings.• The feed system uses a spring-loaded pin arrangement to pass material over the bottom jointing head.• Sectional serrated infeed roll before the top cutterhead.• Variable feed speed by frequency inverter (VFD) with digital display for the feed speed.• Digital thickness control for quickly and precisely setting the desired thickness.• The upper assembly is adjusted for desired thickness by four large-diameter cylindrical posts.• Adjustable infeed bed by easily accessible handwheel to set desired stock removal on the bottom head.• Easy to access swivel control panel with individual ammeters for load monitoring and hour meter to aid in maintenance planning.• Cutterhead starters are Y-Delta providing a soft start to the heads for reduced power consumption on startup.• Automatic lubrication to the conveyor feed system.• High-quality Schneider electrical components to CSA/UL standard.

CANTEK CM626 Single-Sided Planer with Helical Head26" x 11-3/4" capacity Planer w/Helical Cutter HeadFeatures: -- Spiral cutterhead with (6) rows insert knives provides high removal, superior finish, and low noise. -- Solid cast iron construction. -- Variable feed speed. -- Drive top and bottom feed rolls. -- Front & rear bed rollers easily adjusted from the front of the machine. -- Power table elevation by digital thickness control. -- Serrated solid infeed roll. -- Section chip breaker. -- Anti-kickback fingers for added safety. -- Dual heavy jack screws with slides for accuracy & rigidity. -- Dust/Chip exhaust outlet 6"; in diameter. -- Sound dampening machine cover. -- All operations on a convenient control panel. -- Two-sided solid carbide inserts are easily changed while providing optimum wear lifeSpecifications: -- Maximum planing width 26" -- Maximum planing thickness 11 ¾" -- Minimum planning thickness 0.15"; (4 mm) -- Maximum depth of cut 0.31"; (8 mm) -- Minimum planning length 10.35" (263 mm) -- Table area 35" x 27" -- Feed speeds variable 16 – 70 FPM -- Main motor 20 HP -- Feed motor 1 HP -- Table motor 1/2 HP -- Knives 30 x 12 x 1.5 qty 100 -- Cutterhead 4 ¾" dia. x 5000 RPM -- Top feed rollers 3" dia. -- Dust hood outlet 6" dia.

Non-Oscillating Edge Sander with end sanding kit. -- 6" Wide x 108" long belt. -- 6" x 40" Graphite covered platen. -- 1 HP -1.5 HP, or 3 HP -2 HP, 3-Phase motor w/magnetic switch. -- 7" Diameter drive pulley. -- 7-3/4" x 37" Front table with a 6" vertical adjustment. -- End table for radius work with a 6" vertical adjustment. -- Heavy laminated tables, fabricated steel base and swing-away dust hood.

CANTEK - GOODSPEED CP-1250 AP Hydraulic Copy Lathe. -- General Data: 44" Length cap. with 4" min. length of stock and 1/2" - 4" max. diameter cap., hopper feed with automatic chucking, square or round stock can be hopper fed. -- Equipped with: 7.5 HP Spindle motor, 1,800 - 3,200 RPM spindle speed adjustable by pulley change, 3 HP hydraulic motor. -- Complete with: Swivel control panel, PLC sequence controller built into separate control cabinet, (3) pressure gauges, automatic way & support collar lubrication & safety wire mesh across the front of machine. -- Includes: Two hydraulic copiers (rough + fine). Travelling steady rest and installed knives. -- Production capacity: Approx. (5 - 7) pieces/Min for 600 mm length, (3 - 5) pcs./Min for 900 mm length, (2 - 3) pcs./Min for 1,200 mm length, depending on cutting speed, type of material, etc. -- Electrical load: 11.4 amps, 10.5 HP @ 575/3/60.volts.

CANTEK C 12 RS Straight Line Rip SawRuggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2". -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes.Features: 1-Piece cast iron chain with a diamond cut surface for positive material feeding.Includes: Infeed and Outfeed ConveyorTotal amperage is 21.5 and the gross weight approx. 2,530 Lbs

CANTEK MODEL CFS100 / EM-12 DEFECT SAW AND END-MATCHING SYSTEM:Consisting of a CANTEK model "CFS-100" Optimizing Cut-Off Saw followed by a CANTEK Model "EM 12" Through-Feed End Matcher and with the following specifications and features: CANTEK "CFS-100" OPTIMIZING CUT-OFF SAW -- Up to 20 mm X 200 mm or 100 mm X 100 mm( 3/4" X 7.87" or 3.9" X 3.9" cutting capacity with 18" x 30 mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP servo drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed. -- Machine is ideal for separating crayon marked waste zones from useable material before entering into a feed-thru End Matcher; provides (3) times greater production than manual cut-off saws.5% + Material recovery (yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm / 0.40"; control employs a touch screen for easy learning and operation.Features: -- New machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included.(5) Cutting modes include: -- Adjustable end cuts to a max. of 10mm (0.4") -- Fixed length of cutting mode. -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only). -- Cutting on fluorescent marks with double-end trimming (perfect solution for end matching). -- Reading fluorescent marks with double end trim, fixed-length, random length end match, and finger joint block cutting. CANTEK "EM-12" END MATCHER -- Continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity; -- 295 FPM max. feed speed; average speed of 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; -- 5.5 HP Shaper motors, 1 HP feed motor an

CANTEK C251 24" WIDE BELT SANDERSpecifications: -- 24" Width cap. - sanding head with a rubber covered contact roll and adjustable finishing platen, 10 HP motor main drive motor. -- 25" x 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5.9" thickness capacity, Power elevation for thickness opening with digital thickness programming. -- Variable conveyor feed speed from 15 - 50FPM, 1 HP feed motor. -- 5.9" Max. working thickness, 13" min. working length, -- Spring loaded holddown rolls.Complete with: -- Magnetic controls, (2) 4" dia. dust collection outlets, and safety shutoff. - 825 CFM Dust collection required. Optional: 10 HP Single Phase motorElectronic belt tracking for optimum belt life and sanding results. Ammeter for load monitoring main drive motor. Disc brake on the main motor. Pneumatic belt tensioning with quick release outboard support. Safety Interlocks are located on all access doors.

CANTEK C10RSStraight Line Rip Saw --Specifications -- 12" Over cutting Rip Saw ruggedly constructed with cast iron & ground tables, -- Cast iron pressure housing with (6) guide rollers and solid welded steel base chassis -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", -- Feedspeeds of 50, 65 and 85 FPM - 4,500 RPM, --10 HPsaw arbor motor; 1 HP feed motor, --Min. workpiece length 8", max. cutting thickness 3-3/8", --13 3/4" distance between saw and column, -- 30" X 50" table size, 31-1/2" table height. --Equipped with & Features: -- Cast iron upper pressure housing provides a stable mounting for the precision ground & nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- (1)-piece cast iron chain with a diamond cut surface for positive material feeding. --Included: Manual , and several blades and the toolkit.÷

CANTEK - C 12 RS, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 16 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", -- Distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond-cut surface for positive material feeding.

CANTEK R-18 Heavy Duty Straight Line Rip Saw "Cuts From The Bottom"Equipped with & Features: -- Extra Heavy Main Frame Throughout with large support table. -- 6"; Minimum length with this type of saw the blade is cutting downwards, forcing the Blade onto the chain – hence max. stability and safety are realized. -- Better chip clearance for shavings on deep cutting. -- Glue Joint Range – 12"; to 10 Ft.Specifications: -- Depth of Cut 4.7"; (120 mm) max. -- Split chain – double track with HRC60 Rockwell Hardened Guideways. -- 26"; (660 mm) Saw to Column. -- (8) Press Rolls hold material firmly on the track. -- 20 HP Main Motor. -- 3 HP Feed Motor. -- Feed Speed 42 to 164 FPM variable. -- Automatic chain and track Oiler -- 41"; Length of chain above table -- Saw Arbor Height adjustable -- Max. 18"; Blade Diameter x 2"; Bore Dia. saw Arbor with 14 mm pin at 6 5mm centers.Complete with: -- Saw Arbor Brake Included -- Anti-kickback fingers top and bottom -- Dust collection outlets: Top 4" (100 mm), Bottom 6"; -(150 mmm). CFM Required: 1,400 CFM. -- Table Dimensions: 78-3/4"; x 40"; x 33.5"; high (Can be added to optional) -- Net weight - 4400 Lbs. -- Stock Machine Electrics 460/3/60 to UL/CSA Standards (Other voltages available on request)Note: The advantage of cutting from below on thick material, the gullet of the sawblade projects above the stock to clear the shavings halfway through the cut

CANTEK RAPIDEDGE PRO EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Pre-mill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counter rotating cutter-heads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot is designed for EVA hot melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with (2) pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consists of : (1) Large driven roller followed by a smaller one. Workstations: -- End Trim: (1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with (2) saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:The RAPID adjustment system uses a pneumatic 3-position adjustment to quickly change from 0.5 mm to 1 mm, to 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM high frequency motors for Top & Bottom trimming of the panel; each motor has an inset knife cutter head that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding:(1) 0.5 HP (0.37 kW) - 12,000 RPM, high frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm to 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile Scrappers:Multi-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat Scrappers:Flat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units:(2) 0.2 HP (0.12 kW) - 3,000 RPM motors, Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. -- Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Pre-milling Station so any overspray which gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface

CANTEK - MRS-340-M2, ...Rip Saw Multiblade with CAMERON SkewSpecifications -- 4.3" Max. thickness with 14" dia. fixed blade(s); 3.3" with 12" fixed blade(s); 4" with 14" movable blades and 2.95" with 12" movable blades; 13.4" max. working width between outside saws 25.6: max. -- 0verall width; 5-1/2" max. distance to fence from inside fixed blade; 0.59" to 13.38" max. saw travel; 23-1/2" min. stock length; 19.7" possible with optional short stock holddown (reduces thickness capacity). -- With 70 mm dia. x 13-3/4" long saw arbor powered by a 50 HP motor driving the blades at 3,800 RPM; 3 HP feed motor; provides feed speeds from 15 to 135 FPM; -- 0.5 HP Lift motor for holddown roll. -- Infinitely variable saw shifting speeds from 0.78" to 3.15" per second. -- 72" x 31" table size; sits 30" from the floor.Equipped with & Features -- Cast iron main frame with main parts enclosed to ensure protection and perfect stability. -- HD Precision straight line caterpillar-type feed chain with easily replaceable bolt-in cast steel or Urethane chain ads (optional). -- Fully programmable position sets (10) programs of (10) sets each or infinitely variable foot pedal position set; user-friendly -- Touchscreen control (free-standing operators control console) is integrated with 32-bit microprocessor and (2) RS232 ports for incredible positioning speeds and EXACT blade positioning. -- Touchscreen with full and easy programming capabilities and joystick control; saw blade positioning is accomplished by industrial series Servo Motor and control. -- Blade speed is infinitely adjustable from 0.78" to 3.54"/Sec to match all operations; blade positioning can be initiated by electronic joystick control (efficient & quick) or the touchscreen controls. -- (2) Saws independently or (2) saws per shifter (optional as a cluster) or with a single or bank of saws with spacers can be set up on the inside of the saw arbor to Gang Rip, if desired. New short sock-cutting device included. -- Top pressure roll system is electronically positioned from the front control panel for lumber thickness. -- Position readout; top roll holddown system is mated to the Servo positioning short stock shoe to provide optimum straight line ripping and safety; top rolls are spring tensioned and tension is adjustable (pneumatic). -- Specially designed and Patent Pending Precision Glide Lock with nickel chrome steel saw arbor with super technology for easy maintenance and free saw shifting; (2) shifting saw bushings are equipped with specially designed rollers for most accurate and very fast saw positioning. -- (3) Rows of antikickback fingers. -- Variable feeding speeds from 16' to 135' FPM inverter motor and speed control with LED readout. -- Electronic overload sensing system is integrated into the inverter feed system providing automatic speed reduction under heavy amperage load. -- (2) Powered top & bottom outfeed rolls are included; powered roll system facilitates positive flow

CANTEK MRS-340M-1 GANG RIPSAW WITH (1) SHIFTING BLADE and the following specifications and features: Capacities are: -- 4.3" Max. thickness with 14" dia. fixed blade(s); 3.3" with 12" fixed blade(s); 4" with 14" moveable blades and 2.95" with 12" moveable blades; 13.4" max. working width between outside saws. 25.6" max. overall width; -- 5.5" Max. distance to fence from inside fixed blade; 0.59" to 13.38" max. saw travel; 23-1/2" min. stock length; 19.7" possible with optional short stock holddodwn (reduces thickness capacity. -- With 70 mm dia. x 13-3/4" long saw arbor powered by a 50 HP motor driving the blades at 3,800 RPM; 3 HP feed motor provides feed speeds from 15 to 135 FPM;1/2 HP lift motor for hold-down roll; infinitely variable saw shifting speeds from 0.78" to 3.15" per second; (2) 15 mW laser lights; (2) 12" or 14" dia. x 90 mm bore blades; 72" x 31" table size sits 30" from the floor. Features include: -- Cast iron main frame with main parts enclosed to ensure protection and perfect stability; HD precision straight line caterpillar type feed chain with easily replaceable bolt-in cast steel or Urethane chain ads (optional); -- Fully programmable position sets (10) programs of (10) sets each or infinitely variable foot pedal position set; user friendly Touch Screen control (free standing operators control console) is integrated with 32 bit micro processor and (2) RS232 ports for incredible positioning speeds and EXACT blade positioning. -- Touch Screen with full and easy programming capabilities and joystick control; saw blade positioning is accomplished by industrial series Servo Motor and control; blade speed is infinitely adjustable from 0.78" to 3.54" IPS to match all operations; blade positioning can be initiated by electronic joystick control (efficient & quick) or the touch screen controls. Equipped to shift (1) saw independently or (2) saws per shifter (optional as a cluster) or with a single or bank of saws with spacers can be set up on the inside of the saw arbor to gang rip if desired. New short stock cutting device included -- Top pressure roll system is electronically positioned from the front control panel for lumber thickness; includes position readout; top roll hold down system is mated to the servo positioning short stock shoe to provide optimum straight line ripping and safety; top rolls are spring tensioned and tension is adjustable (pneumatic pressure is optional). -- Specially designed and Patent Pending Precision Glide Lock with nickel chrome steel saw arbor with super technology for easy maintenance and free saw shifting; (2) shifting saw bushings are equipped with specially designed rollers for most accurate and very fast saw positioning. -- (3) Rows of anti-kickback fingers; variable feeding speeds from 16 to 135 FPM inverter motor and speed control with LED readout; electronic overload sensing system is integrated to the inverter feed system providing automatic speed reduction under heavy amperage lo

CANTEK MRS-610M-4 GANG RIPSAW WITH (4) SHIFTING BLADES: Specifications: -- (4) Shifting Blades and 4.2" Max. cutting thickness without pressure plate, 3.7" with pressure plate; 24" Max. cutting width; 35.4" Max. material width of pass-through; -- 60 HP Saw motor (larger optional); 2.8" (70 mm) Saw arbor diameter turning at 3800 RPM; 12" Min. or 14" max. Sawblade diameter; 2.8" (70 mm) Sawblade bore when mounted directly on shaft, 3.5" (90 mm) when mounted on saw sleeve; -- 5 HP feed motor with variable feed speeds from 25 to 200 FPM; 1/2 HP pressure roller raising motor; 24" Min. stock length; 31.9" Min. stock length with board under (2) rollers.Features and Benefits: -- The main frame is cast iron, all the main parts are enclosed, ensuring protection and perfect stability -- Nickel chrome steel saw arbor with 70 mm OD double keyed quick removal sleeve. -- Heavy duty precision straight line feeding caterpillar chain type. -- Feed chain with easily replaceable bolt in cast steel or urethane pads - optional. -- The top pressure roller system is electronically positioned from the front control panel with regard to lumber thickness with position readout. -- Top roller hold down system is mated to the servo positioning short stock shoe providing optimum straight-line ripping performance and comprehensive safety. -- Pneumatic pressure (infinitely variable) to the holddown feed rollers provides better control of the lumber. -- Nickel chrome steel saw arbor. -- Variable feed speeds of 16 - 200 FPM. (5 - 60 m/min) via an inverter motor and speed control with led readout. -- Electronic overload sensing system is integrated to the inverter feed system providing automatic speed reduction under heavy amperage load. -- New - short stock cutting device included. -- Digitally controlled lubricator for chain. -- Centralized lubrication system. -- (2) Powered top & bottom outfeed rollers are a standard feature. The powered roll system facilitates positive flow of the stock through the gang saw and onto outfeed conveyors or transfers. -- (3) Rows of anti-kickback fingers. -- Telemechanique - automatic star-delta starter (low amperage soft-start) and low voltage controls -- Controls are mounted on the saw for easy convenient machine operation. -- Includes 12' infeed table -- Gang saw sleeve is an optional extra. -- Electrics to 230/460 or 575-volt, 3-phase, 60-cycle to UL/CSA standards -- Complete Shifting Fence Infeed Tables and complete Outfeed Sweep Systems, handling decks and Stacking Systems are available.Options available: -- Add a 75 HP saw arbor motor instead of 60 HP - including a Wye-Delta low amp Starter. -- 100 HP Saw arbor motor in lieu of 60 HP - including Wye-Delta low amp Starter -- 125 HP Saw arbor motor instead of 60 HP - including Wye-Delta low amp Starter. -- Short Stock Feeding device (min. length 12" - must use 12" blades for max. thickness of cut of 2.16" (55 mm). -- 20 mW Laser (FP MLC1320W) & Laser Holder w/12" B

CANTEK MODEL MRS-175 6.9"; THICK CUTTING HEAVY-DUTY GANG RIPSAW: -- FEATURES: -- Massive cast iron base provides incredible absorption characteristics for high quality deep cutting operations -- Precision chain and rails (dip chain) system facilitates straight line cutting -- Equipped with a blade mist cooling device providing cooling and cleaning for sawblades during cutting increasing blade life and improved cut quality. -- Motorized saw arbor and thickness adjustment for operator convenience. -- Specially designed auxiliary powered outfeed roller assures maximum smoothness of workpiece outfeed especially when working on extra thick, heavy and moist wood. -- A digitally controller lubrication unit is provided to provide consistent oil protection to the feed chain and guide rails. If the oil level drops below a safe level a warning lamp will light up and the feed chain will stop automatically. -- Equipped with an electronic amperage display which is tied in to an overload protection where if the saw motor exceeds a rated amperage the feed chain slows down automatically. This prevents the potential damaged to the saw arbor and/or blades and also prolongs blade life up to 20%. -- Variable feed speed adjustment by frequency inverter from the front of the machine. -- Please note. with safety cover non-CE -- Measurement: 255x210x170(cm)N.W./G.W.:3,150KGS/3,350KGS -- SPECIFICATIONS -- Max. cutting thickness, 6.9"; -- Max. cutting width, 13-3/4"; -- Fixed inside blade to column, 14.9"; -- Min. working length, 27-1/2"; -- Max. saw blade diameter, 14"; to 18"; -- Sawblade bore, 70 mm or 90mm – double keyed -- Saw arbor diameter, 70 mm without sleeve - 90mm with sleeve -- Saw arbor speed, 2500 RPM -- Saw arbor motor, 75 HP (100 HP optional) -- Saw arbor elevation motor, 1/2 HP -- Feed motor, 3 HP (5HP optional) -- Variable feed speed, 8 – 80 FPM (higher speed optional) -- Powered raise & lower of rolls, 1/2 HP -- Dust hood dia., 8"; -- Table height (pass line), 29.3"; -- Electrics – to UL/CSA standards 230/460 or 575-volt, 3-phase, 60-cycle -- Table area (L x W), 72.4"; x 31.1"; -- Overall dimensions (L x W x H), 95.5"; x 90.5"; x 63";, Net weight 6,600 lbs.

CANTEK - MX340, ...Edgebander (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MRS 300 Multi Blade (Gang) Rip Saw: General Description: -- Frame is Cast Iron, all the main parts are enclosed, ensuring protection and perfect stability. -- Straight line caterpillar style feeding with heavy guided chain. Chain blocks are special cast iron with heat treated & precision ground pins. -- Nickel chrome steel Saw Arbor with 70 mm OD – dble. keyed quick removal sleeve.Features & Includes: -- (3) Sets of Anti-Kickback Fingers (2) top, (1) bottom. -- Powered Rise & Fall to the pressure rollers. -- New style round Fence Bar support with quick shift long fence. -- Automatic Centralized lubrication system. -- Automatic Star-Delta Starter (slow speed start) and low voltage controls. -- C.E style European guard & safety features. -- Long fence for control of long material. -- Electrics to 230/460 or 575 Volts, 3-Phase, 60 Cycles.Specifications: -- Max. Working Thickness, 4 5/8"; (120 mm) with 15"; Blade diameter. -- Min. Length, 20"; standard or 12" with short stock attachment. -- Saw Sleeve Usable Length(between outside saws), 12" (305 mm). -- Sawblade Dia., 200 to 350 mm (8"; to 14";). -- Saw arbor Sleeve OD (Diameter), 70 mm; Saw arbor diameter, 50 mm. -- Saw arbor vertical adjustment, 3.6"; (90 mm).Equipped with: -- 50 HP Saw Motor – Saw Arbor Speed 3,800 RPM. -- Powered Pressure Rollers (Rise/Fall), 1/2 HP motor. -- Feed Speeds 25 - 100 FPM (8 - 39 MPM); Feed Motor with 2 HP drive. -- (2) 6"; Dia. Dust Hood. -- Table Size, 30"; x 60"; Table Height from floor 33.5".Other Information: -- Net Weight, 4,510 Lbs, Shipping Weight, 5,060 Lbs - Machine Dimensions, 82.68"; 59"; x 56.5", Shipping dimensions, 71"; x 67"; x 63";. -- Included: (1) Removable saw sleeve, (1) Set of (38) spacers; NOTE: Saw blades not included.OPTIONAL EXTRAS - AVAILABLE:Short Stock & Thin material cutting attachment12"-300mm min. length & 3.75" - 95mm max. thickness (can be added and/or used at any time) (Required for high accuracy cutting) (CANMRS300A-SHT-STK)....................................................................................................................................... $ 620.00 20mW Laser (FP MLC1320W) & Laser Holder w/6"; Bolt on Base-Stand(FP MBN03-XF8000)............................................................................................................ $ 1,020.00 OPTIONAL EXTRAS – AVAILABLE (Cont’d):NEW – Single Blade Mechanical Quick Lock Collars that can be used on the 70mm sleeve for individual blade quick setting and locking process (no spacers required) – This is desirable especially if you have to quick change from size to size and you don’t have the spacers to run a special size of product (Each CANMRS300-AM36-045-0).................................................................................................. $ 210.00 Extra for spare saw sleeve (CANMRS300A-SLEEVE)...................................................... $ 590.00Extra for spare set (38