Equipment For Sale

35 Ton, Contractor Special Neck, Spring Assisted Ramps, 27' Flat Deck, 4' Beavertail, 38" Deck Height, 22.5 Tires, Apitong Wood Floor Same trailer with 22.5 tires, 38" deck height, and Hydraulic Ramps available for $36,900 Same trailer with 17.5 tires, 33" deck height and Spring Ramps available for $33,500 Prices are plus FET

51 Ton Detach Lowboy, 25' Well, 22" Loaded Deck Height, 4 Position Ride Height, Spring Suspension, Open Fenders, Battery Backup Strobe Lights, Apitong Wood Floor, Boom and Bucket Trough. 13hp Honda power unit adds $3,800.00 35 Ton and 55 Ton Trailers are also available Prices are plus FET

51 Ton Contractor Special Neck, 33" Loaded Deck Height, Self Contained Hydraulic Ramps, 30' Flat Deck, 8'6" Upper Deck, 4' Beavertail, Apitong Wood Floor, 17.5 Tires Same spec with Spring Ramps call for pricing 35 Ton Trailer also available Prices are plus FET

55 Ton Detachable Lowboy, 26' Well, 22" Loaded Deck Height, Load Bearing Covered Fenders, Air Ride Lift Rear w/Manual Override, 4 Position Ride Height, Battery Backup, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires 25' Well trailer also available for $65,900 Flip Axles adds $17,500 Honda Power Unit adds $3,800.00 35 Ton and 51 Ton Trailers also available All prices plus F.E.T.

55 Ton Detachable Lowboy, 4th Axle Flip with Covered Fenders and Stobe Lights, 25' Well, 22" Loaded Deck Height, Load Bearing Covered Fenders, Air Ride Lift Rear w/Manual Override, 4 Position Ride Height, Battery Backup, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires Trailer without the Flip is $65,900 26' Well trailer also available for $67,500 Honda Power Unit adds $3,800.00 35 Ton and 51 Ton Trailers also available All prices plus F.E.T.

1999 Pitts 40’ Log Trailer, Center Point Suspension, Rebuilt

2020 PITTS, Plantation Log Trailer, 40', 4"" Drop, 11R24.5 Hub Pilot, Air Ride, Dead Bolster, Maxi Brakes, Grapple Bar, Covered Tandem. Same spec trailer 4 Spring Hutch Susp $25,100 Single Point Susp $27,200 Single Point with Vulcan Scales $30,300 Headboard adds $1,500 All prices are plus FET Please give LMI-Tennessee LLC a call to discuss your financing needs.

CONNECTING LINES INCLUDED FOR CATERPILLAR 926M PJB VOLVO STYLE QUICK COUPLER SOLD AS IS

18 CYD CAPACITY BOLT ON CUTTING EDGE PIN ON LUGGING PJB 982M WOOD CHIP BUCKET SOLD AS IS

FUSION COUPLER LUMBER YARD FORKS 100" SIDE SHIFT MAST FUSION TINES 1.5X8X48, CARRIAGE 60" WIDE

60" CARRIAGE WITH MAST FOR SMALL WHEEL LOADER FUSION INTERFACE PJB LUMBER YARD FORKS SOLD AS IS TINES 1.5"X8"X48"

100" SIDE SHIFT MAST 48" TINES 60" WIDE CARRIAGE ISO LINKAGE PJB SMALL WHEEL LOADER LUMBER FORKS SOLD AS IS

100" MAST 48" TINES INSTALLED 60" WIDE CARRIAGE FOR CATERPILLAR ISO STYLE COUPLER PJB LUMBER YARD FORKS SOLD AS IS

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter

Used but reconditioned Pneumafil Corp. reverse air bag house, sizes range from 12,000 CFM up to approximately 60,000 CFM. Reconditioning includes new paint, new filter bags, rebuilt interior components. Call for pricing.