Equipment For Sale

EXTREMA XF-44.1 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 4-roll Power Feeder with 4-3/4" & 2-1/4" rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Flotation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA DCY-1000 TYPHOON Cyclone Dust Collector. Cyclone & fabric filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a 1/2 HP Rotary Air Lock with 10 CFM capacity, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags; air volume output rated @ 6,400 CFM. -- Equipped with: 10 HP Induction motor, 16" steel blower fan impeller and is dynamically balanced and 12" inlet. -- Includes: Collection bag snap-in ring for easy addition or removal of plastic bag; filter bags filter dust particles down to (1) Micron in size; low noise operation. -- Supplied with: Heavy Duty support frame to allow usage with a waste hopper under the Cyclone.

EXTREMA DC-4100 Baghouse Dust CollectorThe "DC-4100" baghouse dust collector is designed to achieve maximum airflow with a superior filtration area. This is achieved by using (36) smaller diameter filter bags to have more filter media in the same space as other similar dust collectors of its size. More filter area means better airflow with less filter maintenance. A manual bag shaker is included.The DC-4100 meets the NFPA664 CFM requirements for indoor dust collectors. The compact design allows this maximum filtration unit to use a depth of less than three and one half along a wall. The 10HP main motor has a dynamic balanced impellor and a magnetic starter is included.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 361 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (36) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 12".

EXTREMA XF-44.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 4-Roll Power Feeder with 4-3/4" diameter x 2-1/4" wide rubber rollers. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 13 - 26 - 36 & 72 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Flotation of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available).

EXTREMA XF-54T.3 Power Feeder w/Mounting Column;"EXTREMELY" Heavy duty 5-roller CONTINUOUS BELT Power Feeder with (3) 44.5" x 1/2" tracks. -- 1 HP Motor with forward/reversing switch. -- (4) Speeds of 15 - 28 - 39 & 78 FPM. -- Heavy duty cast aluminum construction of the feeder housing. -- Cast iron stand components with fully adjustable mounting column. -- 3/4" Floatation travel of the rollers. -- Standard reach from base is 720 mm / 28-3/8" (optional 850 mm / 33-7/16" arm available)

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

Extrema WS-110 Single Spindle Shaper -- 3/4" & 1" Interchangeable spindles. -- 3 HP Single Phase, 3,450 RPM motor designed for operation in most smaller shops -- Belt drive for spindle speeds of 8,000 & 10,000 RPM _ 2-5/8" capacity under the nut (3/4" spindle) and 3-7/8" vertical spindle travel will accommodate a variety of cutters. -- Large Table size 28" x 30" with a 6" max. dia. table opening -- Includes Fence assembly, miter gauge, 1/2" collet adapter, and power feeder.

EZ CAR - (Used) Model A: Car Crusher Approx: 6,200 hours.New in: 1988.System Pressure: 2,500 PSI.Port Reliefs set at: 2,650 PSI.Cylinders: 10" Bore.Travel: 78".Shaft: 4" rod.OpeningSize: 20" x 8'-1" x 7'-7".OverallWeight: 61,000 Lbs.Length: 43'-1/4."Travel & operating height: 13'-1/4'.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Fabtech 546c log forwarder -engine been rebuilt -new joysticks -most cylinders have been repacked -brand new center section -hydraulic control valve was rebuilt -new log Bunks brand new LED lights -all new window seals with brand new lexan -new hydraulic hoses -new seat -John Deere power Tech 6 cylinder

1999 FABTEK 546B 8 WHEELED DOUBLE BUNK FORWARDER 6 CYL DEERE POWERSHIFT EXTENDABOOM BYPASS BUCKET JOYSTICKS 700 RUBBER

Parting Out Fabtek 153 with 4 Roller Head, Lots of Good Parts

THESE ARE BRAND NEW FABRICATED BUNKS FOR FABTEK FORWARDERS 2000 DOLLARS EACH

THESE ARE BRAND NEW FABRICATED STAKES FOR FABTEK FORWARDER THESE ARE 2300 EACH

Fabtek FT153, 14,000 hrs., $59,900

2006 Fabtek 153 Processor, Equipped with a Fabtek (4) Roller Processor Head, Engine Has 6,100 Hours, was Remaned, Frame Hours 15,800, Enclosed Cab with Heat and Air Conditioning, Undercarriage is 80%, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1998 FABTEK 344B SINGLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS BYPASS BUCKET ROTATER 23.1-26 RUBBER

Fabtek four roller processing head in decent condition. Head does come with computer.

2000 FABTEK 346B DOUBLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS SQUUIRT BOOM

2001 Fabtek FT133, both Knife Cylinders repacked, roller cylinder repacked , main lift cylinder repacked, double grouser style 22.5 " pads, fixed 4 roller Fabtek Processing head, nice machine for the year, and has been well taken care of, $49,500