Equipment For Sale

CANTEK MX-370P EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): --Specifications:0.4 - 3 mm Edge thickness, panel thickness 0.315" - 1.77". Minimum panel length 6.7", minimum panel width 3-¾". Heated infeed fence for better glue adhesion. Fixed feed speed 29 FPM.Equipped with: -- Pre-mill (2) 1.5 kW each (12,000 RPM) counter-rotating cutter-heads for removing up to 3mm of the panel edge. -- Quick change 1.2 kg Teflon-coated glue pot is designed for EVA hot-melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than 1 minute. -- Guillotine shear: The guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consist of one large driven roller, followed by a smaller one. Workstations: -- End Trim: The end trim system is a single motor with (2) saw blades. The unit is mounted on high-precision linear guide rails. -- Top & bottom trimmers with (2) high-frequency motors for top & bottom trimming of the panel. Each motor has an inset knife cutter-head which can be adjusted from flush to beveled finish for thin edges, and radius trimming (2 mm radius). Single motor Corner Rounding Unit Can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm). The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Radius scraping unit fine-tunes the edge radius while removing knife marks during the milling process on radius edging. Insert knives have a 2 mm radius. -- Buffing unit leaves a super finish on ABS and PVC edging and removes any discoloration on the edges.

CANTEK MT-610 24"; Rotary Milling PlanerSpecifications -- Heavy duty welded steel construction. --Moving table type -- Display position number. -- Alarm bell and flash light. -- Speed change for feeding, controlled by Inverter (VFD) -- Rubber Endless Belt. -- Automatic device for feed belt tracking. -- Air jet cleaner for cutter -- Working width 610mm -- Workpiece thickness 3-125mm Equipped with & Features -- Number of cutters 2 units -- Spindle motor power 20 HP -- Brush motor power 1 HP (150 mm dia) -- Vacuum motor power 1 HP (suction for conveyor belt) -- Feed motor power 1 HP -- Lifting motor power 0.5 HP

CANTEK - GOODSPEED CP-1250 AP Hydraulic Copy Lathe. -- General Data: 44" Length cap. with 4" min. length of stock and 1/2" - 4" max. diameter cap., hopper feed with automatic chucking, square or round stock can be hopper fed. -- Equipped with: 7.5 HP Spindle motor, 1,800 - 3,200 RPM spindle speed adjustable by pulley change, 3 HP hydraulic motor. -- Complete with: Swivel control panel, PLC sequence controller built into separate control cabinet, (3) pressure gauges, automatic way & support collar lubrication & safety wire mesh across the front of machine. -- Includes: Two hydraulic copiers (rough + fine). Travelling steady rest and installed knives. -- Production capacity: Approx. (5 - 7) pieces/Min for 600 mm length, (3 - 5) pcs./Min for 900 mm length, (2 - 3) pcs./Min for 1,200 mm length, depending on cutting speed, type of material, etc. -- Electrical load: 11.4 amps, 10.5 HP @ 575/3/60.volts.

CANTEK D405A 10' Sliding Table SawSpecifications: -- Max. cutting length 126". -- Max. depth of cut: 4.13" at 90° (355 mm), 5.12" at 90° (400 mm), 2.75" at 45° (355 mm). -- Main saw: 7-1/2 HP Motor, Blade dia. 16", Arbor dia. 30 mm (1.18"), Arbor tilt 0° - 45°, & Blade speeds 3,000, 4,000, & 5,000 RPM. -- Scoring saw: 1 HP - 8,000 RPM Motor, Blade dia. 120 mm (4.72"), & Arbor dia. 20 mm (0.79").Equipped with: -- 15-1/2"; x 126"; x 35-1/4"; H Precision anodized aluminum sliding table with Prismatic rollers running on precsion ground steel guides, 21.6"; x 35"; x 35.3"; H Cast-iron fixed table, 12.6"; x 32.7"; x 35.3"; H Auxiliary table. -- Main saw blade motorized height & tilt adjustment. -- 39-1/2"; L x 3-1/2"; H Aluminum rip fence, with 130 mm (51.18";) Cutting cap. -- Aluminum extruded crosscut fence, with (2) Flip stops with miter angle adjustment, & Sliding outrigger support. -- Eye-Level touchpad control, with LED Displays for main saw blade height & tilt. -- Overhead blade guard.

CANTEK - SS512TB Tilting Spindle ShaperSpecifications: --Tilting spindle from -5° to +45° and 6" x 43" fence. --1-1/4" interchangeable spindle is standard (other sizes available). -- Large cast-iron table is ground and polished for maximum stability and durability. -- Powerful 7.5 HP motor for even the most demanding profiling work. -- Five spindle speeds can be easily adjusted to suit your tool diameter. -- 5-1/2" Useable spindle length, above table 13-¼"; below table 8-¼". -- Electronic spindle brake for added safety and facilitates fast changeover. -- Precision fence assembly with micro-infeed and outfeed fence adjustment. -- The finger-style fence allows the fence to be adjusted around the cutter for added safety and workpiece stability. -- Table size 31 ½"; x 39.4″. -- Dust port (1) 5″ on guard, (1) 4" into the table.

CANTEK SS512CSB Heavy Duty Production Shaper with Sliding Table & Spindle Brake7.5 HP Features: -- Cast iron sliding table runs on ball bearing for smooth table transition. -- Cast iron ground & polished table with insert rings; table size: 31- ½"; x 39.4″. -- Precision ground and electronically balanced spindle. -- V-belt drive with (5) feed speeds is easily accessed from the front of the machine. -- Electric spindle brake for added safety. -- Spindle lock - with limit switch safety, machine will not start with lock engage. -- Micro spindle height adjustment with dial indicator. -- Interchangeable cutter spindle. -- Forward/reverse spindle rotation. -- Adjustable "finger" type fence Independent micro-fence adjustment on both sides. -- Includes the following standard equipment: 1- 1/4" Spindle, (1) 5"; dust chute on guard & (1) 4"; dust chute in the table, safety guard, Miter tenon jig, and Telemecanique magnetic controls.Net weight 1034 Lbs. Machine dimensions 48.4"; x 39.4"; x 52 ¾";. Shipping weight 1166 Lbs.Shipping dimensions 45 ¼"; x 37"; x 41";

CANTEK MX340 Edgebander (Single Phase or 3-Phase)The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

CANTEK MX350 EDGEBANDER (W/ PRE-MILLING): -- Specifications:0.4-3 mm Edge thickness, panel thickness 8~45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″). Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lb capacity. Two spring loaded pressure rollers (One driven, one idling). Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed. PLC control system with LED display and keypadWorkstations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Top & bottom scrape station 2 mm radius. -- Top & bottom buffing. -- Feed speed 29 FPM

CANTEK - GT635ARD-16 25″ Double Surface Planer25″ Wide x 16″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external handwheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 16″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK GT610HI CARDAN SHAFT DRIVE DOUBLE SURFACE PLANERSpecifications: -- Max. working width 24" (610 mm). -- Max. working thickness 8" (200 mm). -- Min. working thickness 5/16″ (8 mm). -- Min. working length 12" (300 mm). -- Cutterhead RPM 5000 RPMCutterhead diameter 5.3" (135 mm). -- Feed speed 30-98 FPM 10 – 30 m/min. -- Top cutterhead motor 40 HP. -- Bottom cutterhead motor 30 HP. -- Feed motor 5 HP. -- Table Rolls 7 (3) driven. -- Opening hoist motor 1 HP. Machine dimensions: (LxWxH) 112"; x 67"; x 67"; 2830x1700x1700mm . Machine weight 8800 Lbs 4000 kgsShipping weight 9240 lbs 4200 kgs. -- Shipping dimensions (LxWxH) 115"; x 75"; x 75"; 2900 x 1900 x 1900mmMachine electrics (Standard) 460/3/60 = 110 amps (Other voltages on request, factory order)Key Advantages• Cast iron machine frame for superior vibration damping resulting in a long machine & bearing life.• Chrome-plated tables and top and bottom for maximum wear resistance.• Cutterheads are mounted in precision ABEC 7 RHP bearings.• The feed system uses a spring-loaded pin arrangement to pass material over the bottom jointing head.• Sectional serrated infeed roll before the top cutterhead.• Variable feed speed by frequency inverter (VFD) with digital display for the feed speed.• Digital thickness control for quickly and precisely setting the desired thickness.• The upper assembly is adjusted for desired thickness by four large-diameter cylindrical posts.• Adjustable infeed bed by easily accessible handwheel to set desired stock removal on the bottom head.• Easy to access swivel control panel with individual ammeters for load monitoring and hour meter to aid in maintenance planning.• Cutterhead starters are Y-Delta providing a soft start to the heads for reduced power consumption on startup.• Automatic lubrication to the conveyor feed system.• High-quality Schneider electrical components to CSA/UL standard.

CANTEK MX340 EDGEBANDER (COMPACT): (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications: -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations: -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MX340M EDGEBANDERThe MX340 from CANTEK is designed to be a compact, and durable edgebander.Specifications: -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad. -- The MX340 handles panel thickness of 0.315" up to 1.77" (8 mm to 45 mm), -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed). --Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon-coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring-loaded double-pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

CANTEK - MX340, ...Edgebander (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MRS-610M-4 GANG RIPSAW WITH (4) SHIFTING BLADES: Specifications: -- (4) Shifting Blades and 4.2" Max. cutting thickness without pressure plate, 3.7" with pressure plate; 24" Max. cutting width; 35.4" Max. material width of pass-through; -- 60 HP Saw motor (larger optional); 2.8" (70 mm) Saw arbor diameter turning at 3800 RPM; 12" Min. or 14" max. Sawblade diameter; 2.8" (70 mm) Sawblade bore when mounted directly on shaft, 3.5" (90 mm) when mounted on saw sleeve; -- 5 HP feed motor with variable feed speeds from 25 to 200 FPM; 1/2 HP pressure roller raising motor; 24" Min. stock length; 31.9" Min. stock length with board under (2) rollers.Features and Benefits: -- The main frame is cast iron, all the main parts are enclosed, ensuring protection and perfect stability -- Nickel chrome steel saw arbor with 70 mm OD double keyed quick removal sleeve. -- Heavy duty precision straight line feeding caterpillar chain type. -- Feed chain with easily replaceable bolt in cast steel or urethane pads - optional. -- The top pressure roller system is electronically positioned from the front control panel with regard to lumber thickness with position readout. -- Top roller hold down system is mated to the servo positioning short stock shoe providing optimum straight-line ripping performance and comprehensive safety. -- Pneumatic pressure (infinitely variable) to the holddown feed rollers provides better control of the lumber. -- Nickel chrome steel saw arbor. -- Variable feed speeds of 16 - 200 FPM. (5 - 60 m/min) via an inverter motor and speed control with led readout. -- Electronic overload sensing system is integrated to the inverter feed system providing automatic speed reduction under heavy amperage load. -- New - short stock cutting device included. -- Digitally controlled lubricator for chain. -- Centralized lubrication system. -- (2) Powered top & bottom outfeed rollers are a standard feature. The powered roll system facilitates positive flow of the stock through the gang saw and onto outfeed conveyors or transfers. -- (3) Rows of anti-kickback fingers. -- Telemechanique - automatic star-delta starter (low amperage soft-start) and low voltage controls -- Controls are mounted on the saw for easy convenient machine operation. -- Includes 12' infeed table -- Gang saw sleeve is an optional extra. -- Electrics to 230/460 or 575-volt, 3-phase, 60-cycle to UL/CSA standards -- Complete Shifting Fence Infeed Tables and complete Outfeed Sweep Systems, handling decks and Stacking Systems are available.Options available: -- Add a 75 HP saw arbor motor instead of 60 HP - including a Wye-Delta low amp Starter. -- 100 HP Saw arbor motor in lieu of 60 HP - including Wye-Delta low amp Starter -- 125 HP Saw arbor motor instead of 60 HP - including Wye-Delta low amp Starter. -- Short Stock Feeding device (min. length 12" - must use 12" blades for max. thickness of cut of 2.16" (55 mm). -- 20 mW Laser (FP MLC1320W) & Laser Holder w/12" B

CANTEK - C 12 RSH, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 16 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", -- Distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond-cut surface for positive material feeding.

CANTEK - PCM 120, ...Hollow Chisel MortiserFeatures: -- Power stroke of head permits easy, fast, and accurate successive cuts. -- Separate fan blower to keep work clean and free from dust & chips. -- Manual adjustable table height and lateral position. -- Heavy-Duty cast iron construction. -- Convenient centralized control panel. -- Foot pedal actuated cycle. -- Pneumatic workpiece clamping by lever.Specifications: -- Chisel range: 1/4" - 3/4"; Motor; 2 HP; Spindle speed: 3,400 RPM. -- Table: 16-3/4" x 21-1/4; Table tilts 30°. -- Air pressure: 8kG Clamping; Cylinder: 2-1/2"; (63 mm). -- Head traveling cylinder: 3.15"; (80 mm); Table cross travel: 5";. -- Table longitudinal travel: 18";; Table vertical travel: 12";. -- Max. stock width: 12";; Max. mortising depth: 4";. -- Machine weight: 572 Lbs. -- Shipping weight: 726 Lbs; Shipping dimension: 35"; x 38"; x 70"; (880 x 960 x 1,780 mm).

Cantek Horizontal Resaw Great Condition Very Low Hours Voltage 230/480/3

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12"; saw arbor dia. 1"; saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. --:1-Piece cast iron chain with a diamond cut surface for positive material feeding.Total amperage is 21.5 and the gross weight approx. 2,530 Lbs.

CANTEK - P-630HV, ...24" Single Sided Planer with Spiral Knife CutterheadSpecifications: -- Planing width: 24-3/4"; planing thickness: 3/8" - 11-13/16". -- Max. depth of cut: 5/16". -- Min. length: 8-3/4". -- Table size: 26-1/2" x 33-1/2". -- Cutterhead speed: 5,600 RPM. -- Variable feed speeds: 20 - 39 FPM. Equipped with: -- 98 mm (3.86") Dia. Steel spiral knife cutterhead with: (6) Rows of (86) 30 x 12 x 1.5 mm inserts mounted on angle for shear cut & 10 HP Motor. -- 3" Dia. Sectional infeed roller with: 1 HP Feed motor & chip breaker. -- (2) 2-7/8" Dia. idler rollers in table; quick-set adjustment. -- 1/2 HP Bed elevation motor. -- eTEK "CH-525" Digital thickness controller with: LCD Display & Touchpad.Complete with: -- Instruction Manual & Parts List.NOTE: Seller purchased new and states machine has light use.

CANTEK EM-12 End Matcher;1.6" to 12" Width x 0.4" to 1.38" thickness (to 2-1/4" optional) x 10.6" min. length capacity. Unlimited lengths possible.Specifications: -- Feed speeds to 295 FPM with approximate production speeds of 77 FPM (based on 6-1/2' incoming boards). -- Standard 173" long infeed table and standard 86" (2,200 mm) long outfeed table; -- (2) 10 HP cutterhead motors with 40 mm spindle diameters; 1 HP feed motor; 1/2 HP motor drive to cutterhead carriage; clamping pressure from top and side; 24 volt DC controls.Standard equipment and Features: -- Designed for machining tongue & groove with or without V's on flooring and panel products; designed to be used for finger joint cutting. -- Heavy-duty self supporting main frame; compact design requires minimum floor space.Feedworks: -- Capable of processing material as short as 11" to an unlimited length; variable speed through-feed systems is controlled by frequency inverter; through-feed system allows the tongue to be cut simultaneously on the tail of one board and the leading edge of the next board. -- Powered top Urethane rolls and spring loaded bed rollers feed the material into position for processing. -- Pneumatic side pressure ensures the material is held square against the fence.Complete with: -- Safety and noise reduction enclosure; convenient touch screen control is used to quickly activate and adjust the machine functions. -- Powered 176" long infeed conveyor is included (additional length optional); with a 86.6" long outfeed table (additional length optional). -- Includes: (2) Individual Precision Insert Tooling Heads as Supplied with Machine & stacked to make (1) pair of heads; set of heads provided for groove on left and tongue on right.