Northtech 12" Resaw Model NT-HBR12V Self contained hydraulic pack

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

Northtech Chop Saw

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Nyle PHT350 Kiln System was powered up and tested, but not put into production.

There are (5) saws available that range in age from: - 2006 (2) - SOLD - 2007 - SOLD - 2011 - One saw available

Oliver 36" Band Resaw

7.5 HP single phase cyclone/dust collection assorted dust pipe and fittings as pictured

Optimatic TS-06 Tooth Straightener Manufacturer specs: Every Tooth - Every Run - Every Time Introducing the TS06 automatic bandsaw tooth straightener. This latest Filing Room innovation from OPTIMATIC is designed to work in place of the backfeed on a bandsaw sharpener. The TS06 is timed from the feed of the bandsaw sharpener. Each tooth is examined as it passes through the sensor. When a tooth is not aligned properly it will bend it back to correct it. Teeth are examined on each round of the grinder, giving the tooth straightener the opportunity to examine each tooth several times as the saw is processed and make progressive improvement putting the tooth back in line. A standard 5' resaw can generally be processed in 30 minutes. The TS06 is designed to measure the body of the tooth, just below the grinding burr and just behind the swage or tip. The actual contact point is easily adjustable. It's important to measure the body of the tooth so that we do not cover up problems with swages, shapers, or tippers. - but instead provide them a square, strong tooth to work from. 1. The TS06 has two stations. The first station feeds then measures. 2. The second station bends. Specifications:Connection values:Electrical connetion:220 V 50 Hz or special voltageAir Pressure:1/4? Gas threadAir:Minimum 5 bar air consumption, 1 liter per strokeSaw blade diameter:Saw Wide:From 80 mm to 300 mm wide or special up to 420 mmSaw Long:From 6 m in the grinding machine carousel can be integratedSaw Thickness:0,7 mm to 2,7 mmDimensions:Length:1350 mmHeight:1550 mmWidth:600 mmWorking position:1000 mm can be adapted to grinding heightWeight:210 kg

Optimal 4-Side Canter See photos fro complete specs

Peerless Chip Bin MOD 14

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter

Pneumafil Dust Collector Model 135 (13.5-460-8): 150 hp. The round duct enters the collector at 48" Diameter. Dixie Air Dust Collector: Size: 108-12, Type: SPB, 50 HP, Inlet to the motor, circumference is 90".

2000 Povlsen Wide-bandsaw mill. In good working condition 75hp Isuzu Diesel engine and has approximately 1500hrs on it. Mill can saw logs approximately 36"D x 25' L Comes with an Armstrong #2 bandsaw sharpener and approximately 20 new bandsaw blades.

Prater 18" Hammer Mill 40 HP Motor Hammers in good shape New screen

Precision 55 screener, was working when pulled out of production.