BLACK BROTHERS 775-56 Top and Bottom Glue Spreader with Extra Tall Opening for SIP PanelsDescription & Specifications:1. Top and Bottom glue spreader2. Upper elevator machine opening to 12 - 1/2" opening3. Pass line-height 30"4. Variable speed drive by inverter 40 - 120 fpm5. Electrical interlock on upper and lower Nip Guards6. Operating control bars7. NEMA 12 electrical enclosure 575 Volt, 3-phase power8. Coating rolls rubber 7 - 3/4" dia OD, 14 TPI with 1/2" Cross Hatch Grooving.9. Doctor rolls chrome 6 - 1/2" dia ODThis is a 2007 machine but has never been put into operation and is ready to go, it has 575 volts, you may need a transformer.

BLACK BROTHERS 22D-875-62 Top & Bottom Glue SpreaderSpecifications: -- 62" Working width, 8-3/4" dia. Grooved Neoprene applicator roll with 24 TPI, 6-1/2" dia. smooth Neoprene doctor roll -- Lower elevator opening 0" - 4-1/2", -- Single speed of 88 FPM with 1.5 HP drive; -- NEMA 12 electrics. -- Complete with: Push button magnetic starter, safety guards, all warning labels.

BLACK BROTHERS - 22-D-875-32, ...Top Only Glue Spreader.Capacity 32" Working width. -- 8-3/4" Dia. Rubber roll -- 6-1/2" Dia. chromed steel doctor rolls. -- Top elevator opening w/Readout -- Constant pass line: 36-3/4" -- Outfeed roller conveyor -- 7.5 HP MotorComplete with:1 Spare rollerNOTE: Machine is currently wired for 220v

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. grooved rubber covered applicator rolls, 6-1/4" chrome plated doctor rolls -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar. -- Top elevator style glue spreader, constant pass line --Main Motor 1HP, 3ph --Feed speed 88FPM --Thickness adjustment via manual hand crank

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. Grooved rubber covered applicator rolls, 6-1/4" hard rubber covered doctor rolls --Main motor 1.5hp -- Bottom roll adjustment -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar.NOTE: Currently wired for 460v

BLACK BROTHERS - Cold Press Laminating Line (Complete)with: BLACK BROTHERS - APP PL: 5 x 12, 50 PSI End-Loading Fixed Opening Air Pod PressCurrent line setup: Infeed Scissor Lift; Panel Pusher; Panel Cleaning Brush; Glue Spreader; Stack building Scissors Lift; Laminate Rack over Conveyor; Stack Staging; Press Loading Conveyor; Cold Press. -- Station 1: Pneumatic Panel Feeder. Panel Pusher feeds individual panels from side loaded (w/Forklift) Scissor Lift into Panel Cleaner. Photoelectric eye activates arm that pushes panel into Panel Cleaner. Pusher Arm: Feed panels into machine on demand. Switch: Remote mounting. Pass Line: 44"; 24" Stroke with 4' of adjustment: Feeds panels from 1/2 thickness (up to 250#) in lengths of: 8', 10', or 12'; controls on (Left or Right). NEMA 12 Enclosure with: Main power disconnect switch & overcurrent protection: 230 or 460 Volt: 3-Phase; 60 Hertz, 24 VDC Control Circuits. Dual Limit Switch Arrangement controls the Scissors Lift with: "Hand/Auto" selector; Barrier Guard to prevent double board feed. -- Station 2: Scissors Lift. 36" Vertical travel foot operated raise/lower switch. 48" x 120" Plain deck with: 6,000 Lbs Capacity. Pin adjustable edge guides, mounted on: SL & Anchor Clips for mounting. Transverse Conveyors with: Air brake to allow loading or unloading from side. -- Station 3: MIDWEST AUTOMATION - PC160: Panel Cleaner. 63" Working width capacity; (2) spiral type cleaning brushes; 0" - 3" thickness opening; single end adjustment with roll opening (scale-type) indicator. Variable feed speed 30 - 150 FPM with: 1 HP - 1,725 RPM Drive; (2) 6" dia. infeed & (2) 6" dia. outfeed rolls; variable brush speed with: 3 HP Motor. - Equipped with: All guards, dust hoods, and magnetic starter. -- Station 4: BLACK BROTHERS - 775: Top & Bottom Adhesive Spreader; 68" width capacity. Application: Apply water-based adhesive to top & bottom particle board, plywood, and MDF substrate. Upper Elevator: 0 - 4-1/2" Opening. Roll opening indicator: Shows opening between rolls in 0.001 increments. Riser Base: 44" Pass line height. Caster arrangement: (4) Plain rigid casters with guide track & lock. Coating Rolls: (2) 7-3/4" Max. O.D.; 60 durometer - neoprene/SPR; grooved: 16 TPI. Doctor Rolls: (2) 7" Max. O.D.; 100 durometer - ebonite; ground smooth single-hand wheel doctor roll adjustment with: Mechanical digital readout. - Electrical Interlocks on nip guard(s). NEMA 12 Enclosure with: Main power disconnect switch & overcurrent protection. 1-1/2 HP Single speed with: 3" Reverse lockout 88 FPM. Pivoting infeed table. Operating handwheels & controls: Parallel to the direction of flow on the right; motor on left end. Operating control bars. Liquid level control: FIBER OPTIC. Machine mounted double diaphragm pump: l" Ports; alumi

BLUE GIANT SFSRH33/575 Scissor LiftHydraulic 3,000 Lbs. scissors lift -- 34" x 108" platform with idle roller -- Low 9" x high 53",Hydraulic pumping unit with 3 HP motor.

BLUM - Mini Press: Hinge Borer -- Tabletop "Mini Drill" unit for BLUM Hinge Boring; 1.5 HP (1.1 kW) - 2,450 RPM drill head assembly for hinge cup boring. -- Head assembly rotates for several hinge & drawer system boring patterns; pneumatic drill cycle with air blow-off. -- Includes: 48" x 24" Tabletop. -- Machine also used for line boring by purchasing an auxiliary BLUM spindle head; not included. -- Complete with: 3-Drawer mobile storage base for all hinge components.

BOARKE - BKM-43103RRK: (3) Head 42″ Wide Belt Sander (3 NEW Drums)43" Width cap.: Drum, drum, platen.Head Configuration1st Head: 30 HP; 10″ Helical grooved drum.2nd Head: 25 HP; 10″ Helical grooved drum.3rd Head: 20 HP; Helical grooved (idler) with a platen. Specifications -- 42″ Width capacity; 5″ height capacity running. -- 43″ X 103″ Abrasives. -- 1st Head: 30 HP; 10″ helical grooved drum. -- 2nd Head: 25 HP; 10″ helical grooved drum. -- 3rd Head: 20 HP Helical grooved (idler) with a platen. -- 1st & 2nd Heads: Dial indicators to dial in abrasives; has optional 5 HP vacuum feed bed.Equipped with & Features: -- Feed: Variable from 7 - 45 FPM via a 2 HP motor; VFD for speed control. -- Feed Mat: Thick; with usual crazing, but plenty of life. -- Elevation: Handled by a 1/2 HP motor. -- Machine includes: Digital readout; touchpad control combined with auto thickness calibration unit on the right.

BOARKE (HOLZ-HER) - BKM-37RK2: 2-Head Wide Belt Sander37" Width cap. Drum & Combination Head.Head Configuration1st Head. Rubber-covered contact roll; 6-1/4" dia.; 20 HP motor.2nd Head. Combination head with: 6-1/4" Dia. rubber covered contact roll (50-Shore); 3-1/8" wide finishing platen; 15 HP motor.Specification -- Abrasive belt size: 37" x 75". -- Air tensioning & electronic abrasive belt tracking. -- Conveyor belt feed with: 2 HP Variable feed drive. -- 9 - 45 FPM Feed speed with inverter.Equipped with & Features: -- Infeed & outfeed rubber covered holddown rollers. -- 1/8" - 7" Max. motorized thickness opening. -- LED Readout thickness. -- Part "over-thickness" protection. -- Automatic conveyor belt tracking. -- Emergency stop button. -- Motor load meters. -- Magnetic controls.NOTE: Very clean machine; low hours: Only ran prototypes; replaced with 3-head machine for production.

BOERE - TPK-900, ...Planer Sander with (2) Heads -- 2-Head, 900 mm (36") width cap.; -- Equipped with (1) Knife planer head and (1) Rubberized Drum. -- 1st Head. Helical knife planer head with: (4) Spirals of 4-sided carbide inserts, each 14 mm x 14 mm; 20 HP motor. -- 2nd Head. Drum approx. 10" dia. rubber covered contact roll; 15 HP motor; all heads with air-operated caliper disc brakes. -- Variable feed speed: 13 - 52 FPM; 2-1/2 HP motor; automatic conveyor belt tracking; -- Anti-kickback fingers on infeed; infeed hold-down shoes' double outfeed pinch rolls on outfeed. -- Motorized part thickness adjustment: 0" - 6"; LED readout display. Complete with: -- Controls are mounted on the belt loading side, load meters for each head, and conveyor infeed extension.

BOERE - TKS 900, ...2-Head Top Wide Belt Sanding Machine900 mm (36") Working width; equipped with: (1) Contact roller, (1) Fine sanding pad. Head Configuration -- 1st Head: Rubber contact roller, spirally grooved, Shore hardness 80, diameter 265 mm (10.4"), driven by 18 kW (25 HP) motor. -- 2nd Head: Sanding pad, electronic-pneumatic controlled, 114.7 kW (20 HP); Air blowing unit for cleaning the abrasive belt. -- All heads use abrasive belts size: 910 x 1,900 mm (35.8" x 74.8").Feed System -- Variable feed speed: From 5 - 25 MPM (16 - 82 FPM); 1.5 kW (2 HP) motor. -- Motorized part thickness opening: 3 - 150 mm (0.1" - 6"), driven by 0.12 kW (0,15 HP) motor.Complete with: -- Emergency Stop Systems for abrasive belt breakage and low belt tension. -- Infeed safety bar for operator protection and oversized parts. -- Automatic Star Delta starters, motor load meters. -- Pneumatic belt tension. -- Emergency Stops at the front & back. -- Extended infeed belt, approx. 42" long.Actual model: BOERE "TKS 900".

BOILERSMITH 400 HP BOILER, WOOD-FIRED -- Wood-Fired BOILERSMITH Boiler fitted with CHALLENGER Combustion Unit. -- Complete with the following major components and features: -- 250 PSIG design pressure. -- BOILERSMITH Boiler Model HRT2H8-2600SF-XW-250 with 2600 Sq. Ft. boiler surface area. -- Fuel can vary in moisture up to 50%. (Boiler HP is reduced as moisture increases.) -- Fuel feed Auger with Variable Frequency Drive. -- Fire-Tube Boiler with integrated Air Blast Tube Cleaning. -- De-Ash Augers. -- All Electrical Controls and starters. -- All mechanical/electrical engineer's drawings.NOTES: Removed and ready to load onto two trucks, 38,000 and 42,000 pounds. 15,000 to 16,000 pounds per hour steam if burning wood pellets. No building included but same building can be purchased from STAR.

BRANDT KDF 660 Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

CAM-WOOD SM-732 HS 7-Heads High-Speed Trough Feed Moulder(7) Heads (B-R-L-T-T- T-B), working cap. 111 13/16" x 6-1/4"".Specifications: -- Max/Min working width 11 13/16" - 3/4" -- Max/Min thickness 6 1/4" - 5/16" -- Minimum length 9-1/2" -- Head sequence: Bottom 20 HP, right 15 HP, left 15 HP, top 20 HP, top 20 HP, top 15 HP and bottom 15 HP motor. -- All Horizontal spindles have outboard bearings -- Spindle dia. 50 mm with cutterhead speed of 6,000 RPM. -- All spindles are equipped with mechanical digital readouts, "Dual mechanical" readouts on the left and top spindles. Mechanical readouts for pressure elements and chipbreakers; all chipbreakers and pressure elements with pneumatics. -- Feed works: Inverter driven 15 HP feed system with feed speeds of 20 - 260 FPM. -- Infeed table 2M (6'6"), chromed tables, and fences. Side pressure roller mounted at infeed. Features and complete with: -- PNEUMATIC LOAD INFEED SIDE PRESSUREWhile high speed feeding, the side pressure on infeed table ensures every timber close to the fence even under different width. It's convenient to adjust quickly. --OVER HEiGHT PROTECTIONIn case workpiece exceeds the rated maximum height, it will be restricted by the over height protection device provided at the workpiece infeed end. -- HYDRAULIC OUT-BOARD BEARING SUPPORT TOP AND BOTTOM SPINDLESpecially designed hydraulic supports on the top and bottom spindles assure maximum stability while performing high speed and heavy duty machining. -- PNEUMATIC LOAD SIDE PRESSURE WHEELS The front side air pressure wheel on left vertical spindle fully eliminates problem when feeding short or narrow stock not smoothly. The pressure plate is easy and quickly to adjust. -- PNEUMATIC LOAD TOP PRESSURE PLATEThe front pressure plate for top spindle is available to apply an air loading device ensuring maximum stability while performing high speed cutting -- CENTERAL LUBRICATION POINTThe lubrication point are located at the centralized plate for convenience. -- POWERED INFEED TABLE ROLLER The roller in the infeed table is powered, providing a smooth feeding effect for feed stock. -- VERTICAL SPINDLE AXIAL ADJUSTMENT UP TO 60MMIt allows fitting several tools on the vertical spindle, eliminating troublesome cutter change. The 60mm spindle adjustment provides full utilization for a single cutter. -- CENTRALIZED PRESSURE ADJUSTMENT• All pressure regulations for the entire pneumatic system are centralized at the front of the machine for added convenience in pressure adjustment, and sectional pressure adjustments for all pressure rollers ensure consistent pressure.• Clear numerical indicators are provided to correspond directly to the pneumatic mechanisms on the machine, allowing operators to make adjustments based on different processing requirementsAvailable options: -- Automatic Jointer for all (6) heads add: ...$45,600 -- Digital (electronic) display for X and Y axis for each head add $ 3,200 /per head -- NC Automatic positioning control sys

CAM-WOOD BR-OO42BX DOUBLE ROW LINE BORERHeavy Double Head Line Borer with (2) 21-spindle heads; 32 mm spindle spacing.Specifications: -- Drilling from the bottom up and with 5-1/2" - 23-1/2" distance between rows. -- Drilling vertically from the bottom allows the chips to drop down falling out of the holes. -- Drilling depth of up to 3" max., takes only seconds to set. -- (2) 2 HP - 3,400 RPM motors; spindles with steel gears & high quality bearings. -- Easy repetition by (2) air index pins for continuous line drilling, left and right roller track supports extend up to 400 mm (15-3/4") for larger panels.Features and Includes: -- 120" Back fence with (4) repeat "flip" stops; includes 27-3/4" (704 mm) fence for quick positioning of flip stops. -- (6) Pneumatic holddowns to automatically actuate when the drill cycle begins. -- (42) "Quick Change" chucks for easy tool change. -- Magnetic motor controls and 1/4" air regulator with filter and oiler; 100 PSI required air pressure.

CAM-WOOD BR-2132 Boring Machine21-Spindle boring head on 32 mm centers with position indicator.Features & Specifications: -- Stops in 0° & 90° with pneumatically assisted positioning in vertical & horizontal. -- 0" - 3" Adjustable drilling depth with speed control. -- Head height fine adjustment with mechanical digital readout. -- 2 HP - 3,400 RPM Motor. -- Cast iron 37-1/2" x 19-1/4" table with side fences for mirror-image. -- Line boring fence with repeat stops. -- Foot actuated pneumatic clamps & drill cycle.Complete with: Magnetic starter, overload protection. -- Optional: Quick-change chucks $28.00 ea.

CAM-WOOD WS-M1000 NAX Planer Sander -- 2 Heads with 39.4" width capacity planer head and combination sanding headFeatures: -- This machine is especially designed for tale off heavy materials such as glue panel, bend board, rough lumber. -- The first head is a knife planer head, with 25 HP motor. The spiral planer cutterhead is fitted with 14 x 14 mm, four edge throw away Tungsten Carbide knife inserts, providing superior chip removal rate, minimum noise, and extremely smooth cutting effect. Changing knife inserts are conveniently done without removing the cutterhead. -- The second head is a combination of drum and platen driven by a 20 HP motor, belt size 40.5" x 78 3/4". (1030mm X 2000 mm) -- Anti-kickback fingers, mounted at the infeed of the machine, this anti-kickback finger gives a safety guard for the operator. -- Insufficient pressure protection, in case insufficient working air pressure occurs, the machine brakes automatically for safety guard.Irreversible running of pressure roller, runs a single direction only, giving an additional safety guard for panel kickback. -- Motorized elevation of conveyor table (micro-computer controlled with digital readout), it accurately displays the position of the conveyor table and automatically moves to the setting thickness for planning, sanding. -- Panel cleaning brush roller; built at outfeed end of the machine, this cleaning brush roller cleans the powder on the sanded panel. -- Hold-down plate is hard chrome treated for maximum wear resistance.Technical Specification: -- Working width 39.4" (1000 mm). -- Working thickness up to 6 1/4". -- Minimum working length 21". -- Feed speed 10 to 90 FPM inverted driven by 3 HP motor. -- Table raised and lowered by 1/2 HP motor. -- Cleaning brush driven by 1/2 HP

CAM-WOOD WS-MN700NAX Planer/Sander Equipped with: -- (2) Heads with 27" width capacity planer head and combination sanding head -- This machine is specially designed for take-off heavy materials such as glued-up panels, bend boards, and rough lumber. -- The first head is a knife planer head, with 20 HP motor. The spiral planer cutterhead is fitted with 14 x 14 MM, four edge throw away Tungsten Carbide knife inserts, providing superior chip removal rate, minimum noise, and extremely smooth cutting effect. Changing knife inserts are conveniently done without removing the cutterhead. -- The second head is a combination of drum and platen driven by a 20 HP motor, belt size 28 3/4" X 75" -- Anti-kickback fingers, mounted at the infeed of the machine, these anti-kickback fingers provide a safety guard for the operator.Features: -- Insufficient pressure protection, in case insufficient working air pressure occurs, the machine brakes automatically for safety guard.Irreversible running of pressure roller, runs a single direction only, giving an additional safety guard for panel kickback. -- Motorized elevation of conveyor table (micro-computer controlled with digital readout), it accurately displays the position of the conveyor table and automatically moves to the setting thickness for planning, sanding. -- Panel cleaning brush roller; built-in at the outfeed end of the machine, the cleaning brush roller cleans the fine sanding dust off the sanded panel. -- Hold-down plate is hard chrome treated for maximum wear resistance.Technical Specification: -- Working width 27" -- Working thickness up to 6 1/4" -- Minimum working length 20" -- Feed speed 20 to 90 FPM inverted driven by 3 HP motor -- Table raised and lowered by 1/2 HP motor -- Cleaning brush driven by 1/2 HP

CAM-WOOD BR-50 Universal Boring MachineFeatures & Specifications: -- 3 HP Pneumatic Universal Boring Machine, all adjustments feature an index plate for accurate and convenient reading, workplace clamping. -- Vertical Base travel, 24". Horizontal Base travel 12". -- 0" - 4" Spindle stroke, 7/16" - 14-thread screw shank, 1/2" max. bit capacity. -- Table Size: 15" x 22". -- Complete with: Air operated overhead holddown clamp and foot pedal operated drill cycle. -- Drill Head can be swiveled 360° and Optional Multi-Spindle drill heads available.