//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i6c WALKER 14" Bench-Top Vertical Band Saw Specifications: Table size 17” LR x 18" FB x 20” H. Maximum height under guard 8". Equipped with: 3/4 HP - 1,725 Motor. 16” Rubber-covered spoked wheel.

WEB MECAHNICAL JET 10M Jet Air Oven Supply Side complete with the following: -- 400,000 BTUH rating, 3,200 CFM forward curved blower, 5 HP motor 575 V /3 Ph /60 Cy. -- Inlet filter section HEPA 99% DOP rated, Magnehelic gauge across the filter section. -- Thermometer to show outlet temperature, Thermostat to set and control temperature design from 60° -70° C, -- Jets designed to control flow across the belts. Exhaust Side complete with the following: -- Vane axial fan set to exhaust 600 CFM,1/2 HP motor. -- Direct drive fan with motor out of air stream, external grease fittings for lubrication.Heating Module: -- Air makeup sized for 3,200 CFM, 2 HP motor, rated for 400,000 BTUH. --Fan to exhaust through 2"; pleated filter and 12"; HEPA filter, Down discharge,3 HP motor, 3,200 CFM @ 2.0"; E.S.P. -- Engineered for 90° F temperature rise, 0.4 MBTU/hr hydronic coil, features FUJI temperature selector. Conveyor: -- Robust 10-gage steel frame, Novo 40 grey belt designed for up to 90° C and with Auto tracking mechanism. -- Large size 6"; driver and idler pulleys, Support pulleys 3"; as required. -- Heavy duty NORD gear box and a 2 HP direct coupled motor. OPTIONAL (Not included in Price):IR Adder (Lamps): -- Three (3) MW IR lamps in the center of the oven, Three (3) MW IR lamps at the end of the oven, -- Heated length of lamps 54";, dual gold plated element, 3,200 watts per bulb. -- Lamps are designed to sit between the jets on the oven with lamps 8"; (200 mm) above belt and 8"; apart. - Please add ...$ 7,700Control Panel for the above (600 V - Electric) complete with: -- Line interlock, E-stop, fuses, disconnect switch, DC power supply. -- Phase angle controller to control two (2) banks of three (3) lamps. CSA approved panel. - Please add ...$ 12,100BOILER: -- One (1) RBI dominator boiler "DB 600" to supply up to 600,000 BTUH. - Please add ...$ 18,900

WEB MECHANICAL HYDRONIC OVEN - Low Velocity Flash Off - STAGE # 1 and High Velocity Bake Oven - STAGE # 2 STAGE # 1, Low Velocity Flash Off Oven. -- The oven consist of one (1) only hot water oven, 14' wide x 9' high x 30' long with Air flow requirement of 30 FPM/ 9,000 CFM.Supply side complete with the following: -- 400 000 BTUH heat exchanger -- Motor/blower, 2 HP 575 V / 3 Ph / 60 Hz -- Thermometer to show outlet temperature -- Thermostat to set and control temperature to design temperature -- RTD's (1) for accurate oven dispersion temperature -- Eighteen gage galvanized steel panels -- Perforated metal side walls for even air distribution -- Design temperature of 30 -40°C -- Adjustable inlet mixing damper with intake filter (70% recycle) -- Exhaust fan for combustible gasesExhaust will be complete with the following: -- Size 14 direct drive aluminum fan wheelset to exhaust 30% of the contaminated airflow (2,500 CFM) -- Direct drive with the motor out of air stream -- External grease fittings -- Fan module c/w aluminum extrusions and galvanized panels, and will be complete with HEPA style filter, -- DWDI fan, space for hot water heat exchanger STAGE 2 HIGH-VELOCITY OVEN BAKEThe oven consist of one (1) only hot water oven, 14' wide x 9' high x 20' long with Air flow requirement of 50 FPM/ 9,000 CFM Supply side will be complete with the following: -- 1,500,000 BTUH heat exchanger -- 10,000 CFM -- Motor/ blower 5 HP 575v / 3 Ph / 60 Hz -- Thermometer to show outlet temperature -- Thermostat to set and control temperature to design temperature -- Eighteen gage galvanized steel panels c/w 3" insulation -- Perforated metal side walls for even air distribution -- Design temperature of 40 - 60C 104 - 140 F -- Adjustable inlet mixing damper with intake filter (85% recycle) -- Exhaust fan for combustible gases Exhaust will be complete with the following: -- -- -- Size 12 direct drive aluminum fan wheelset to exhaust 15% of the contaminated airflow (1,500) CFM) -- Direct drive with motor out of air stream -- External grease fittings There will be two (2) air knives one at start of the oven and one art the exit to control heat and fume exhaust Air knives will be complete with Multivee filters for inlet air Fan module c/w aluminum extrusions and galvanized panels will be complete with HEPA style filters, DWDI fan, space for hot water heat exchanger.

--MAKE OFFER!---VERY GOOD CONDITION-- WEEKE BHP 100/VANTAGE 480 FLAT TABLE MACHINE, with ATC, Boring, Infeed Roller & Outfeed & 4,771 Hrs. (As of 10/31/23) Specifications: 4' x 8' Bridge style gantry machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. Working Area: 'X" axis 99.21" (2,520 mm), "Y" axis 49.21" (1,250 mm), Max. material thickness of 3.94" (100 mm). Travels: “X” axis 146.06” (3,710 mm), “Y” axis 81.30” (2,065 mm), “Z” axis 13.70” (348 mm) Routing, 8.46” (215 mm) Boring. Positioning Speed: "X" & "Y" axis Vector speed is 314 FPM (96 MPM), "Z" axis 65 FPM (20 MPM); The head travels via AC brushless drives & THK linear motion guides on all axes. Worktable: User-Friendly "S/C Tech "MATRIX" grooved phenolic vacuum table for easy vacuum pod placement. (2) Fixed LH side & (2) Fixed RH side pneumatic pop-up positioning stops. Boring Unit: (1) 3 HP (2.3 kW) Motor, variable speed for 1,500 - 7,500 RPM; (21) Independent vertical spindles with (8) in "X" axis, (9) in "Y" axis (1st Row), & (4) in "Y" axis (2nd Row). Machining: (1) 12 HP (9 kW) Air Cooled High speed constant duty Router with HSK F63 adaptor, 1,250 - 24,000 RPM, constant torque achieved at 9,000 RPM, RH or LH rotation (1) 14-Position tool changer Carousel located at the back side of the spindle carriage. Machine & Operator Control: PC Front-End with WEEKE "Power Control + Windows + WoodWOP operating system. 17" TFT Color graphic monitor, Hand-held control pendant, Foot pedal control; "BECKHOFF" Programmable logic control for (3/4) axes, linear, circular & helical interpolation; The controller is contained in a separate free-standing, dust-free control cabinet that can be placed at either the LH or RH side of the machine. Complete with: 488” W x 96” L Infeed electric/hydraulic Scissor Lift platform, with 3” x 3” Support beams on 7” Centers; 4’ L Roller track intermediate table; vacuum arm with (2) 10” dia. vacuum pads; rake off-feed System; 49” W x 10’ L x 36” H Outfeed motorized belt conveyor; BUSCH "MM 1322 A VM3" 10 HP (7.6 kW) 300 mbar Vacuum Pump; 6’ H Safety fencing. Actual model is WEEKE BHP 100/VANTAGE 480 Machine Dimensions: 292” x 202” x 96” H. Machine with Scissor Lift Dimensions: 389” x 202” x 96” H. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

WEEKE BHP 200 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications:5' x 12' Bridge style gantry machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. -- Working Area:'X" Axis 145.6" (3,700 mm), "Y" axis 61" (1,550 mm), "Z" axis stroke is 12.8" (325 mm), max. material thickness of 4" (100 mm). -- Positioning Speed:"X" Axis is 164 FPM (50 MPM), "Y" axis is 131 FPM (40 MPM), "Z" axis 66 FPM (20 MPM);The head travels via AC brushless drives & THK linear motion guides on all axes. -- Worktable: User-Friendly "S/C Tech "MATRIX" grooved phenolic vacuum table for easy vacuum pod placement, divided into (2) work zones.(4) Front pneumatic pop-up positioning stops, (2) side pneumatic pop-up positioning stops & (4) back pneumatic pop-up positioning stops. -- Boring Unit:(1) 4 HP (3 kW) motor, variable speed for 1,500 - 7,500 RPM;(10) Independent vertical spindle with (5) in "X" axis & (5) in "Y" axis. -- Machining:(1) 12 HP (9 kW) High speed constant duty Router with HSK F63 adaptor,1,250 - 24,000 RPM, constant torque achieved at 9,000 RPM, RH or LH rotation(1) 8-Position tool changer magazine located at the back side of the spindle carriage.Router is powered by an 14 kW programmable frequency inverter. -- Machine & Operator Control:PC Front-End with WEEKE "PC 85T" + Windows "XP" + WoodWOP 5.0 operating system.17" TFT Color graphic monitor, keyboard for data entry, PC 85T hand control pendant; CD R/W & floppy drives, EtherNET interface for LAN connection to office PC, RS-232 serial interface, USB ports. -- Complete with:(1) 500 m³/Hr Vacuum pump, safety mats & safety fencing. -- Actual model is WEEKE BHP 200

WEEKE VANTECH 512 CON2/BHP 008 FLAT TABLE MACHINE (W/ATC/BORING): + AUTO IN-FEED/RAKE/OUT-FEED: -- Specifications:5' x 12' Flat Table "Bridge Gantry" machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. -- Working Capacity: "X" Axis 156.7" (3,980 mm), "Y" axis 61" (1,550 mm), "Z" axis stroke is 9.6" (243.8 mm); max. material thickness is 3.9" (99 mm). -- Positioning Speed:"X" & "Y" Axes 315 FPM (96 MPM); "Z" axis is 82 FPM (25 MPM).The head travels via AC brushless drives & THK linear motion guides on all axes. -- WorktableUser-Friendly "S/C Tech MATRIX" grooved phenolic vacuum table for easy vacuum pod placement.(6) Pop-up pneumatic locator/positioning on the front side & (1) on the back side in "X" axis & (2) pop-up pneumatic locator/positioning pins on RHS facing side in "Y" axis.(4) Vacuum Table work zones can be used independently or together for full table area Foot pedal vacuum zone controls. -- Boring Unit1.5 kW (2 HP) Motor, with "Quick Change" drill bit holders; programmable variable speed from 1,500 - 7,500 RPM; -- Machining(1) 12 HP (9 kW) High speed constant duty, variable speed electro-spindle router with "HSK F 63" adaptor.Router is programmable from 1,250 - 24,000 RPM, RH or LH rotation.(1) 10-Position ATC rack located at the end of machine. -- Operator InterfacePC Front-End with: WEEKE "PC 85T" + "Windows XP" + WoodWOP Operating System.17" TFT Color graphic monitor; keyboard for data entry; PC 85T hand control pendant; central USB hub; Ethernet interface for LAN connection to office PC; RS-232 serial interface.BECKHOFF Programmable logic control for (3/4) axes, linear, circular & helical interpolation; the controller is contained in a separate freestanding, dust-free control cabinet that can be placed at either the LH or RH side of the machine. -- Complete with: (4) 100 cbm/Hr Vacuum Pumps; safety light curtain (the machine will stop when the Operator enters the work area); safety fencing; separate control cabinet. - Manuals & Documents -- Options Include: NC Controlled Touch-Off Tool Probe, length measuring device. (1) NC controlled scissor lift/vacuum in-feed device. (1) NC controlled, powered flat belt outfeed table with Automatic Dust Control Vacuum Sweep Arm Rake system. Laser fence surround for safety -- Actual Model is: WEEKE VANTECH 512 CON2/BHP 008.

WEEKE BHP 100/VANTAGE 480 FLAT TABLE MACHINE, with ATC, Boring, Infeed Roller & Outfeed & 4,771 Hrs. (As of 10/31/23) -- Specifications:4' x 8' Bridge style gantry machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. -- Working Area:'X" axis 99.21" (2,520 mm), "Y" axis 49.21" (1,250 mm), Max. material thickness of 3.94" (100 mm). -- Travels:“X"; axis 146.06"; (3,710 mm), “Y"; axis 81.30"; (2,065 mm), “Z"; axis 13.70"; (348 mm) Routing, 8.46"; (215 mm) Boring. -- Positioning Speed:"X" & "Y" axis Vector speed is 314 FPM (96 MPM), "Z" axis 65 FPM (20 MPM);The head travels via AC brushless drives & THK linear motion guides on all axes. -- Worktable:User-Friendly "S/C Tech "MATRIX" grooved phenolic vacuum table for easy vacuum pod placement.(2) Fixed LH side & (2) Fixed RH side pneumatic pop-up positioning stops. -- Boring Unit:(1) 3 HP (2.3 kW) Motor, variable speed for 1,500 - 7,500 RPM;(21) Independent vertical spindles with (8) in "X" axis, (9) in "Y" axis (1st Row), & (4) in "Y" axis (2nd Row). -- Machining:(1) 12 HP (9 kW) Air Cooled High speed constant duty Router with HSK F63 adaptor,1,250 - 24,000 RPM, constant torque achieved at 9,000 RPM, RH or LH rotation(1) 14-Position tool changer Carousel located at the back side of the spindle carriage. -- Machine & Operator Control:PC Front-End with WEEKE "Power Control + Windows + WoodWOP operating system.17" TFT Color graphic monitor, Hand-held control pendant, Foot pedal control;"BECKHOFF" Programmable logic control for (3/4) axes, linear, circular & helical interpolation;The controller is contained in a separate free-standing, dust-free control cabinet that can be placed at either the LH or RH side of the machine. -- Complete with: 488"; W x 96"; L Infeed electric/hydraulic Scissor Lift platform, with 3"; x 3"; Support beams on 7"; Centers; 4’ L Roller track intermediate table; vacuum arm with (2) 10"; dia. vacuum pads; rake off-feed System; 49"; W x 10’ L x 36"; H Outfeed motorized belt conveyor. BUSCH "MM 1322 A VM3" 10 HP (7.6 kW) 300 mbar Vacuum Pump; 6’ H Safety fencing. -- Actual model is WEEKE BHP 100/VANTAGE 480Machine Dimensions: 292"; x 202"; x 96"; H.Machine with Scissor Lift Dimensions: 389"; x 202"; x 96"; H.

WEEKE VANTECH 510 V7 PO FLAT TABLE MACHINE (LOADING & UNLOADING): -- Specifications:5' x 10' Flat Table "Bridge Gantry" machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. -- Working Area:"X" Axis is 122" (3,100 mm), "Y" axis 61" (1,550 mm), "Z" axis stroke is 9.6" (243.8 mm), max. material thickness of 3.9" (100 mm). -- Positioning Speed:"X" Axis is 236 FPM (72 MPM), "Y" axis is 203 FPM (62 MPM), "Z" axis 82 FPM (25 MPM).The head travels via AC brushless drives & THK linear motion guides on all axes. -- Worktable: User-Friendly "S/C Tech MATRIX" grooved phenolic vacuum table for easy vacuum pod placement.(2) Pop-up Pneumatic locator/positioning bars, one on each side in "X" axis & (1) Pop-up pneumatic locator/positioning pins in "Y" axis.(4) Vacuum Table work zones can be used independently or together for full table area Foot pedal vacuum zone controls. -- Machining:(1) 16 HP (12 kW) High speed electro-spindle router with "HSK F 63" adaptor; constant duty, variable speed from 1,250 - 24,000 RPM, RH or LH rotation.(1) 8-Position ATC rack located at the end of machine. -- Operator Interface:PC Front-End with WEEKE "PC 85T" + Windows "7" + WoodWOP operating system.17" TFT Color graphic monitor, keyboard for data entry, PC 85T hand control pendant; central USB hub, EtherNET interface for LAN connection to office PC, RS-232 serial interface, "BECKHOFF" Programmable logic control for (3/4) axes, linear, circular & helical interpolation; the controller is contained in a separate free-standing, dust-free control cabinet that can be placed at either the LH or RH side of the machine. -- Complete with:(2) 225 m³/Hr Vacuum pumps; safety light curtain (the machine will stop when the operator enters the work area), safety fencing, separate control cabinet. -- Options Include: Boring unit with 2 HP (1.5 kW) motor & (7) Independent vertical spindles with "Quick Change" drill bit holders; programmable variable speed from 1,500 - 7,500 RPM; Touch-off tool length measuring device (1) SCHMALZ "Jumbo Ergo 85" Vacuum Lift (1) NC controlled, powered flat belt outfeed table (1) Automatic Dust Control Vacuum Sweep Arm/Rake system. -- Actual Model is WEEKE VANTECH 510 V7 PO

WEEKE - VANTECH 512: Flat Table Machine (w/ATC/Boring) -- Specifications 5' x 12' Flat Table "Bridge Gantry" machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. -- Working Capacity "X" Axis 156.7" (3,980 mm); "Y" axis 61" (1,550 mm); "Z" axis stroke is 9.6" (243.8 mm); max. material thickness is 3.9" (99 mm).÷ Positioning Speed "X" & "Y" Axes 315 FPM (96 MPM); "Z" axis is 82 FPM (25 MPM). -- The head travels via AC brushless drives & THK linear motion guides on all axes. -- Worktable: User-Friendly "S/C Tech MATRIX" grooved phenolic vacuum table for easy vacuum pod placement. -- (6) Pop-up pneumatic locator/positioning on the front side & (1) on the back side in "X" axis & (2) pop-up pneumatic locator/positioning pins on RHS facing side in "Y" axis. -- (4) Vacuum Table work zones can be used independently or together for full table area foot pedal vacuum zone controls. -- Boring Unit: 2 HP (1.5 kW) motor; 3,450 RPM motor with: (7) Independent vertical spindles; (4) in "X" axis & (3) in "Y" axis. -- Machining: (1) 12 HP (9 kW) High speed constant duty, variable speed electrospindle router with "HSK F 63" adaptor. -- Router is programmable from 1,250 - 24,000 RPM, RH or LH rotation. -- (1) 10-Position ATC rack located at the end of machine. -- Operator Interface: PC Front-End with: WEEKE "PC 85T" + "Windows XP" + WoodWOP Operating System. -- 17" TFT Color graphic monitor; keyboard for data entry; PC 85T hand control pendant; central USB hub; Ethernet interface for LAN connection to office PC; RS-232 serial interface. -- BECKHOFF Programmable logic control for (3/4) axes; linear, circular & helical interpolation; the controller is contained in a separate freestanding, dust-free control cabinet that can be placed at either the LH or RH side of the machine. -- Complete with: (4) 100 cbm Vacuum Pumps; safety light curtain (the machine will stop when the Operator enters the work area); safety fencing; separate control cabinet. - Manuals & Documents. -- Options Include: NC Controlled Touch Off Tool Probe length measuring device. (9) HSK F63 Tool Holders, as pictured. -- Actual Model is: WEEKE - VANTECH 512 OPTIMAT NBP084.

WEEKE ABD 050 CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:(1) Horizontal drilling aggregate with (1) individual spindle; with servo control of the "X" Axis; (1) glue & dowel injector with glue flow control; (1) vibrating hopper dowel feeder. -- Working Capacity:Part size: Length 20 mm - 1,250 mm (.75" - 49") Width 20 mm - 800 mm (.75" - 31.5") Thickness 10 mm - 60 mm (.4" - 2.4") thick.Machine is set up for 8 mm Dia. x 30 or 35 mm long dowels -- Work Area(2) Separate working fields with (4) pneumatic top clamps can process up to (2) parts independently on the left-hand, right-hand or center stops; work pieces can be loaded in (1) field while being machined in the other to allow fast production of varying parts. -- Operator Interface:PC Front-end with Homag Power Control PC 85T, WoodWOP 5.0 operating system with graphic programming & error messaging.17" TFT flat screen monitor, CD-RW drive, 1.44 MB floppy drive, standard keyboard & mouse; Software allows program design with automatic mirror-image by use of an active center stop located 600 mm (23.6") from zero. -- Complete with:Bar code control reader. All manuals, documentation & program disk provided with machine. -- Actual Model is WEEKE ABD 050.

WEEKE ABD 100 CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:(1) Horizontal drilling aggregate with (1) individual spindle; (1) glue & dowel injector with glue flow control; (1) 23" Dia. x 4" D vibrating hopper dowel feeder. -- Working Capacity: Material size from 20 mm - 1,250 mm (.75" - 49") long, 50 mm - 800 mm (1.9" - 31.5") wide, 10 mm - 60 mm (.4" - 2.4") thick. Machine is set up for 8 mm dia. x 30 or 35 mm long dowels (additional dowel sizes are optional). -- (2) Separate working fields with (4) 2-3/4"; LR x 3"; FB pneumatic top clamps can process up to (4) parts independently on the left-hand, right-hand or center-stops; work can be loaded in (1) field while it is being machined in the other to allow fast production of varying parts. -- Operator Interface:PC Front-end with Windows XP + Weeke "WoodWOP 5.0" operating system with graphic programming & error messaging; USB front side bus, 17" TFT flat screen monitor, CD-RW drive, Modem, standard keyboard & mouse.Software allows program design with automatic mirror-image by use of an active center stop located 600 mm (23.6") from zero. -- WEEKE "ABD 100" is designed for small or large capacity horizontal drilling, gluing and dowel insertion; built on a Heavy Duty welded steel base; main horizontal beams hold the carriage for the boring head and glue/water injector. -- Complete with: HAND-HELD PRODUCTS "ADAPTUS 5.0 3800G04E" Handheld Barcode Reader.

WEEKE ABD 050 CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:(1) Horizontal drilling aggregate with (1) individual spindle; with servo control of the "X" Axis; (1) glue & dowel injector with glue flow control; (1) vibrating hopper dowel feeder. -- Working Capacity:Part size: Length 20 mm - 1,250 mm (.75" - 49") Width 20 mm - 800 mm (.75" - 31.5") Thickness 10 mm - 60 mm (.4" - 2.4") thick.Machine is set up for 8 mm Dia. x 30 or 35 mm long dowels -- Work Area(2) Separate working fields with (4) pneumatic top clamps can process up to (2) parts independently on the left-hand, right-hand or center stops; work pieces can be loaded in (1) field while being machined in the other to allow fast production of varying parts. -- Operator Interface:PC Front-end with Homag Power Control PC 85T, WoodWOP 5.0 operating system with graphic programming & error messaging.17" TFT flat screen monitor, CD-RW drive, 1.44 MB floppy drive, standard keyboard & mouse; Software allows program design with automatic mirror-image by use of an active center stop located 600 mm (23.6") from zero. -- Complete with:Bar code reader. All manuals, documentation & program disk provided with machine. -- Actual Model is WEEKE ABD 050/12/NA.

WEEKE ABD 260 CNC BORE GLUE & INSERTER -- Specifications:Designed for small or large capacity horizontal drilling, gluing and dowel insertion; built on a Heavy Duty welded steel base; main horizontal beams hold the carriage for the boring head and glue/water injector.Support Table with a left and right side stop as well as a rear stop bar, center stop pneumatically activated. Eight (8) clamping cylinders, manually adjustable, automatic central lubrication. -- Working Capacity: Material size from 20 mm - 2,800 mm (.75" - 110.25") long, 100 mm - 800 mm (3.9" - 31.5") wide, 10 mm - 80 mm (.4" - 3.5") thick. Machine is set up for 8 mm Dia. x 30 mm or 35 mm long dowels (additional dowel sizes are optional). -- Horizontal Drilling and Dowelling Aggregate: with (3) individual spindle on 32 mm centers; (1) glue & dowel injector with glue flow control; (1) vibrating hopper dowel feeder. -- Vertical Three Spindle Drilling Unit: with (3) individual selectable spindles at 32 mm spacing, adjustable in "Y"- direction from 0 to 50 mm, minimum workpiece width 100 mm. -- (2) Separate stations process: (2) parts independently on the left-hand or right-hand stops or (1) large piece as required with no additional setup; work can be loaded in (1) field while it is being machined in the other to allow fast production of varying parts. -- Operator Interface: Power Control PC Front-end with Microsoft Windows based control + Weeke "PC85T" + "WoodWOP" operating system with graphic programming & error messaging.17" TFT flat screen monitor, CD-RW drive, 1.44MB floppy drive, standard keyboard & mouse. Software allows program design with automatic mirror-image by use of an active center stop located 1,380 mm (54.3") from zero. -- Includes: All manuals, documentation and program disk provided with machine.

WEEKE BP 80 CNC MACHINING CENTER: -- Specifications: X-Axis 122.6 (3,105 mm); Y-axis 40.3" (1,020 mm); Z-axis stroke is 5.3" (135 mm); max. material thickness 3.9" (100 mm). -- Positioning Speed:X-Axis is 213 FPM ((65 MPM); Y-axis 164 FPM ((50 MPM) & Z-axis is 49 FPM (15 MPM); head travels on THK linear ways on all axes. -- Worktable:(6) Movable support rails with: (2) Square matrix vacuum cups ea.; (6) pneumatic backstops & (2) pneumatic side stops creating (2) working zones. -- Boring Unit:2 HP (1.5 kW) Motor; (11) independent vertical spindles: (6) in X-Axis & (5) in Y-axis; (6) horizontal spindles with (1 + 1) in X-axis & (1 + 1) in Y-axis; (1) X-axis grooving saw with 100 mm dia. blade. -- Machining:(2) 7.5 HP (5.6 kW) High speed routers with: "Hydro-Grip" Spindle & EPT 25 adaptors, 6,000 - 18,000 RPM; controlled by frequency inverter. (One of the router spindles is not operational & needs rebuilding.) -- Operator & Machine Control:PC Front-End with: HOMATIC + Windows + WoodWOP 4.0 Operating System; NUM PLC for (3) axes; linear, circular & helical interpolation;15" monitor; keyboard for data entry; floppy disk drive; 40 MB hard drive,;32-bit processors; RS-232 port for possible connection to office PC; all mounted in separate free-standing control cabinet. -- Complete with:(1) 40 cbm/Hr Vacuum Pump; safety mats. -- Actual model is: WEEKE - BP 80

WEEKE BHX 200-25 OPTIMAT CNC MACHINING CENTER (VERTICAL): + PANEL RETURN SYSTEM + CLAMEX-P PROCESSING: -- Specifications: Flexible "Vertical" Machining Center that uses less than 10 sq/m of valuable floor space in addition to an innovative Panel Handling System. -- Working Cap.:Max. workable part size for "X" axis is 120" (3,050 mm); "Y" axis 49.2" (1,250 mm) max. part thickness 3.1" (80 mm).Min. worktable part size for "X" axis is 13.8" (350 mm); "Y" axis 2.36" (60 mm); min. part thickness of 0.31" (8 mm) automatic infeed & outfeed. -- Positioning Speed:The BHX 200 can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axes & 50 FPM (15 MPM) in "Z" axis with total safety; provides an unmatched working capacity. -- Boring Unit:(1) 3 HP (2.3 kW) Motor, variable speed from 1,500 - 7,500 RPM; (15) independent spindles with: (9) Spindles in "X" axis & (6) spindles in "Y" axis.(10) Horizontal spindles with: (3 + 3) in "X" axis & (2 + 2) in "Y" axis; boring block has "QUICK CHANGE" spindle system. -- Operator & Machine Control:WEEKE "POWERTOUCH" + Windows "7"+ WoodWOP Operating System; "i5" Processor.21.5" HD multitouch Wide Screen Display Monitor; soft-touch keypad & USB connection; Digital Field Bus System; RS-232 Serial ports, Ethernet connection.Real-time multitask processing; programs can be transferred via USB or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure; complete set of safety devices. -- Options Include:(1) NC Controlled 0° - 90° "X/Y" Grooving Saw for max. 125 mm dia. x 5 mm thick blade.(1) 13.4 HP (10 kW) Air-Cooled electrospindle router with HSK F3 adaptor; variable speed from 1,500 - 24,000 RPM.(1) 4-Position ATC tool rack mounted on the side of the machine base.(1) "CLAMEX-P Connecting Hardware Processing System; ...watch the Literature Video @ 3:45!(1) NC Controlled Panel Return System; ...watch the Literature Video @ 4:30! -- Actual Model is: WEEKE - BHX 200-25 OPTIMAT

WEEKE BHX 050 CNC MACHINING CENTER (VERTICAL): -- Specifications: Flexible "Vertical" Machining Center that uses less than 5 sq/m of valuable floor space, in addition to an innovative Panel Handling System. -- Working Cap.:Max. workable part size for "X" axis is 98.4" (2,500 mm); "Y" axis 33.4" (850 mm); max. part thickness 2.4" (60 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness of 0.47" (12 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning Speed:The "BHX 050" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axes & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit:(1) 3 HP (2.3 kW), Variable speed from 1,500 - 7,500 RPM motor, (8) independent vertical spindles with: (4) spindles in "X" axis & (4) spindles in "Y" axis.(3) Horizontal Spindles with (1+1) in "X axis & (1) spindle in "Y" axis.Boring block has QUICK-CHANGE spindle system. -- Operator & Machine Control:WEEKE "POWER CONTROL" + Windows + WoodWOP 6.0 + Operating System; "IntelCore 2 DUO" Processor.17" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:&#9679 (1) "X" Axis grooving saw; 9,000 RPM, saw blade dia. 100 mm. &#9679 (1) 7 HP (5 kW) Electro-spindle router with hydraulic "QUICK-CHANGE" tool system & "ETP 25" tool holders; variable speed from 6,000 - 18,000 RPM. -- Actual Model is WEEKE BHX 050.

WEEKE BHX 050 CNC MACHINING CENTER (VERTICAL): -- Specifications: Flexible "Vertical" Machining Center that uses less than 5 sq/m of valuable floor space, in addition to an innovative Panel Handling System. -- Working Cap.:Max. workable part size for "X" axis is 98.4" (2,500 mm); "Y" axis 33.4" (850 mm); max. part thickness 2.4" (60 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness of 0.47" (12 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning Speed:The "BHX 050" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axes & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit:(1) 3 HP (2.3 kW), Variable speed from 1,500 - 7,500 RPM motor, (6) independent spindles with: (4) spindles in "X" axis & (2) spindles in "Y" axis.Boring block has QUICK-CHANGE spindle system. -- Operator & Machine Control:WEEKE "POWER CONTROL" + Windows + WoodWOP 5.0 + Operating System; "IntelCore 2 DUO" Processor.17" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:&#9679 Max. workable part size for "X" axis is 120" (3,050 mm. &#9679 (1) "X" Axis grooving saw; 9,000 RPM, saw blade dia. 100 mm. &#9679 (1) 7 HP (5 kW) Electrospindle router with hydraulic "QUICK-CHANGE" tool system & "ETP 25" tool holders; variable speed from 6,000 - 18,000 RPM. -- Actual Model is WEEKE - BHX 050.

WEINIG P-22 Feed Through Moulder5-Head WEING Molder with a working cap. 9-1/16" x 4-3/4".Head sequence: -- Bottom 10 HP, right/left 10 HP, top 15 HP, and bottom 10 HP motor. -- Spindle dia. 1-1/2" with cutterhead speed of 6,000 RPM; mechanical spindle brakes all spindles. -- Mechanical digital readouts on all spindles; Digiset readouts on left & top spindles; mechanical readouts on chipbreaker & pressure elements of top spindles.Feed: -- Controlled feed speed from 16 - 78 FPM, 5.5 HP feed drive. -- Infeed straightening table 2 M (6-1/2"), fences, side holdover roller mounted to infeed table, manual Waxilit pump.Features: Reduced distance feed roller, protection against backlash when splitting, central location of lubrication points, and sound/safety enclosure. -- It comes with a large assortments of cutter heads 9 inch - 2 inch approximately (30) and it includes a lot of different knives for each of the heads

WEINIG UNIMAT 10005-Head (B-R-L-T-B), 9-1/16" x 4-3/4" cap. -- Head sequence: Bottom 10 HP, right 15 HP, left 15 HP, top 25 HP and bottom 20 HP motor. -- WEINIG "Memory Re-Dial" system with storage of (100) separate profiles; electronic LED readouts for all spindles. -- Spindle dia. 1-13/16" with the following cutterhead speeds; Spindle #1 at 6,000 RPM, spindles #2 - #5 at 7,000 RPM with high precision bearings & mechanical spindle brakes; adjustment of vertical spindles 3-1/8" axially. -- Electronic LED readouts for chipbreaker & pressure elements for top spindles. -- Cutting circles 8-7/8" on spindles #2 - #5; vertical spindles with adjustable table plates to cutting circles, hardened infeed bed plates before-and-after 1st bottom head. -- Motorized feed beam adjustment; variable feed speed from 20 - 118 FPM, 10 HP inverter controlled Cardan feed drive, overhead feed wheels with pneumatic pressure. -- (1) Powered table roller in bed at outfeed. -- Infeed straightening table 2 M (6-1/2') with adjustable fence and adjustable table at outfeed. -- Equipped with: Central location of lubrication points, side pressure roller at infeed, manual waxilit pump, and (2) lights inside sound enclosure. -- Includes Set-Up Stand.Note - Machine is in good running condition, but electric brakes are not functional, but does not affect running or performance.

WEINIG HYDROMAT H 1000 MOULDER (FEED THROUGH):5-Head (B-R-L-T-B), working cap. 9-1/16" x 6-5/16" capacity. -- WEINIG H 1000 spindle sequence: Bottom 15 HP, right 10 HP, left 10 HP, top 20 HP, and bottom 15 HP motor. -- Spindles: Dia. of 1-13/16" with cutter-head speeds of first head 6,000 RPM, 2,3,4,5, at 8,000 RPMs; mechanical digital readouts on all spindle adjustments. Pneumatic pressure elements on left & top head chip-breakers. -- Feed drive, variable feed speed from 20 - 120 FPM, all feed wheels driven and with pneumatic pressure. -- Central lubrication, automatic table lubrication pump, machine prepped for lateral feeder, sound enclosure, safety hood with (1) inside lights.