DOUCET - BT 3-48: Return Conveyor for Edgebanders with Panel TurnerFor Left-Hand feed Edgebanders with Right-Hand Return Conveyor. -- Receiving table: 66" L x 96" W; Return Conveyor: 48" W with total length of 38'. -- Unit can process: 48" Wide x 108" length. -- Minimum part capacity: 4" x 12" For the side turner.Options Include: -- Side mounted "PT 90" Panel Turner; 22" W x 89" L. -- Panels are turned 90° as part of the transfer process between the Receiving and Return Conveyor, eliminating panel overhang.Actual Model: BT3-48-H30-5-38-D-PT

Doucet SRH-48L-31-T Return Conveyor for Edgebanders For RIGHT-HAND feed Edgebanders with LEFT-HAND return conveyor. -- SpecificationsMin part sizes on conveyors: 12"; x 12"; -- Min part sizes on conveyors as equipped with panel deviator: 4" x 12" -- Max panel sizes feeding all 4 sides: 66" x 66" -- Max panel sizes feeding long sides: 66" x 96" -- Max panel weight capacity: 150 lb -- Conveyor pass Height: 30-42"; -- Receiving table Minimum speed: 9.14 meters per minute (30ft/min) -- Receiving table Maximum Speed: 27.43 meters per minute (90ft/min) -- Return conveyor speed 18-54 meters per minute(60-80ft/min) -- Variable conveyor speed 30 to 90 feet/min. -- Belt transfer speed is fixed at 180 feet/min and return -- Return conveyor speed is adjustable 60 to 180 feet/min. -- FeaturesPneumatic actuated down-stroke transfer belts which raise and lower to transfer the receiving panel to the return conveyor rollers. 48" wide x 5’ long receiving conveyor with 2" Ø steel rollers covered with black vinyl, 10mm belt driven individually every 3" centers -- 48" wide x 31' long return conveyor with 2" steel rollers covered with black vinyl, 10mm belt driven individually every 3" centers -- Belt transfer device 6" wide featuring 9 transfer belts -- Transfer by-pass switch -- Variable speed switch located on operator console -- One rail located along the return section of the conveyor to support long and narrow pieces, adjustable in height -- A panel deviator to redeploy narrow parts over several rollers -- PT-90 panel turner to return long rectangular panels lengthwise rather after finishing -- Actual Model is Doucet SRH-48L-31-T

DURA-QUIP - VC-3532, ...Vibrating Conveyor: -- Specifications:35" Wide x 32' Long; Pan is 7" deep and has 1/4" round holes punched plate in most of length to allow sawdust to drop outside of Conveyor. -- Bottom frame is filled with concrete 12" deep and rests on coil springs to isolate vibration from the ground. Buyer to replace screens. -- Include: 10 HP TEFC 460 V Drive motor.

DUST TECHNOLOGY DT-50 Modular Dust Collector5 HP BALDOR Motor, compact 2-bag free-standing & self-contained Heavy Duty Dust Collector, rated @ 2,400 CFM, 9" - 11" static pressure at fan. -- Equipped with: 10" Inlet dia., (2) Cotton Filter bags with 66 sq. ft. filter area and (2) Plastic Collection Bags w/ 30 cu. ft. collection capacity. -- (2) Double "T" Bolt Straps and (2) Quick Release Metal Straps. Includes: Magnetic Starter

DUST TECHNOLOGY DT-150 Modular Dust Collector Free-standing self-contained internal air system, 15 HP Motor, rated for 6,000 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 133 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. -- Includes: 15 HP motor, magnetic starter, (4) Upper cloth filter bags with 133 sq. ft. filter area and (4) lower plastic disposable collection bags

DUST TECHNOLOGY DT-75 Dust Collector7.5 HP BALDOR Motor, compact 3-bag free standing & self-contained heavy-duty dust collector, rated @ 3,450 CFM, 9" - 11" static pressure at fan. -- Equipped with: 12" Inlet dia., (3) upper filter bags with 99 sq. ft. filter area (patented BEANE bags designed to be 99% efficient to .5 microns). -- Dynamically balanced sand cast poured aluminum high quality impeller with easy access; 45 Cu. ft. collection cap., dust is collected in 6-mil thick clear plastic or canvas collection bags for easy disposal or reuse, a unique adjustable baffling system assures even filling of bags. -- Includes: Manual motor starter with thermal overloads & push button station.

DUST TECHNOLOGY DT-100 Dust Collector3-Bag free-standing & self-contained heavy-duty dust collectorSpecifications: -- 10 HP BALDOR Motor, compact 3-bag free standing & self-contained heavy-duty dust collector, rated @ 4,450 CFM, 9" - 11" static pressure at fan. Equipped with: -- 12" Inlet dia., (3) cotton needle felt upper filter bags with 99 sq. ft. filter area or patented BEANE bags designed to be 99% efficient to 0.5 microns. -- Dynamically balanced sand-cast poured high-quality aluminum impeller with easy access; 45 Cu. ft. collection capacity. -- Dust is collected in 6-mil thick clear plastic or canvas collection bags for easy disposal or reuse, a unique adjustable baffling system assures even filling of bags. -- Includes Push-button Magnetic starter control.Dimensions: 24" Deep x 136" High x 107-1/2" Length; Weighs (810) Lbs.

DUST TECHNOLOGY DT-250 Modular Dust Collector Free-standing self-contained internal air system, 25 HP Motor;Specifications: -- Rated for 9,800 CFM, 5-bag unit, 75 cu. ft. collection capacity. -- (5) Upper cloth filter bags with 165 sq. ft. filter area; 16" inlet dia., dust baffling system to fill bags evenly. Supplied with & Includes: -- 25 HP motor with magnetic starter, -- (5) Upper cloth filter bags and (5) lower plastic collection bags. -- (5) Double "T: Bolt straps. -- (5) Quick release metal straps. -- Roll of 50 Lower Plastic Dust Collection Bags, 24" Dia. X 72" Long.Three Year Comprehensive Warranty

DUST TECHNOLOGY DT-200 Modular Dust Collector Free-standing self-contained internal air system.Specifications: -- 20 HP Motor, rated for 7,500 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 132 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. Features & Includes; -- 20 HP motor, magnetic starter; -- (4) Upper cloth filter bags and (4) lower plastic collection bags. -- (4) Double "T": Bolt straps. -- (4) Quick release metal straps. -- Magnetic starterThree Year Comprehensive Warranty

DUST TECHNOLOGY DT-200 Modular Dust Collector W/ Chip TransferFree-standing self-contained internal air system.Specifications: -- 20 HP Motor, rated for 7,500 CFM. -- (4) Upper cloth filter bags with 132 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. Includes; -- (2) Rotary Air Lock units with hoppers. 8" Bottom discharge openings. -- (1) Fan box (DT-FB-100) w/ 10 HP, 4,450 CFM blower unit w/ 12" main inlet diameter. -- (1) Master control panel. Made in the USA. Three Year Comprehensive Warranty

DUSTEX W-2500 Whispurr 5-Bag Dust Collector. -- 8,500 CFM; 25 HP ultra quiet, self-contained high efficiency internal return (5) bag dust collector; 16" Dia. inlet, dynamically balanced impeller. -- Unit includes: (5) 60" filter bags, straps, gaskets, magnetic bag holders. -- Includes: Collection hopper w/ rotary air lock,

DUSTEK M750 Interior Filter Bag Dust Collector7.5 HP Motor, compact 3-bag free standing & self-contained heavy-duty dust collector. -- Rated @ 3,450 CFM, 9" - 11" static pressure at fan. -- Equipped with: 12" Inlet dia., (3) upper filter bags with 99 sq. ft. filter area . -- Dynamically balanced aluminum impeller with easy access; 45 Cu. ft. collection cap., dust is collected in 6-mil thick clear plastic for easy disposal, a unique adjustable baffling system assures even filling of bags. -- Weighs (750) Lbs., 24" Deep x 136" High x 107-1/2" Length.

DUSTEK W-2500 Whispurr 5-Bag Dust Collector.Specification: 8,500 CFM; 25 HP ultra quiet, self-contained high efficiency internal return (5) bag dust collector; 16" Dia. inlet, dynamically balanced impeller. -- Unit includes: (5) 60" filter bags, straps, gaskets, magnetic bag holders. -- Includes: Magnetic starter.

DUSTEK - M750: Interior Filter Bag Dust Collector7.5 HP Motor; compact 3-bag free-standing & self-contained Heavy-Duty Dust Collector. -- Rated @ 3,450 CFM; 9" - 11" static pressure at fan. -- Equipped with: 12" Inlet dia.; (3) upper filter bags with 99 sq./ft. filter area. -- Dynamically balanced aluminum impeller with: Easy access; 45 cu./ft. collection cap.; dust is collected in 6-mil thick clear plastic for easy disposal; a unique adjustable Baffling System assures even filling of bags.

DUSTEK C1000 Dust Collector. -- Free standing collector with 10 HP, 3,600 RPM motor, (3) bag unit, 12" inlet diameter & 4,000 CFM. -- 45 square feet filter area, 100 cubic feet collection capacity. -- System uses inexpensive collection bags for easy disposal or reuse. -- Complete with: Magnetic starter. -- New Filter Bags. -- New rods. -- New bag holders.

DUST-EX AG22 Abort Gate/Valve.... Automated two-way air stream diverter valve which prevents fires and explosions in dust collection systems and reduces the risk of fire in explosive prone work environments. A "safety measure essential" when clean air is returned to a building. -- Consists of: A lever arm that automatically directs a flapper damper in two different directions. -- Normal Position: The damper stays in a horizontal position (open) allowing the air stream to be directed/returned to the building -- Abort Mode: In the event of a spark originating upstream of an outside dust collector, a Spark Detection Sensor positioned in the air stream inside the building, sends a signal to de-energize an electro-magnetically controlled latch.The flap of the valve is very quickly switched to the abort/second position (closed) thereby diverting the explosion pressure/air stream to the atmosphere. Thus the inside work environment is protected from the explosion. -- Reset Mode: A pneumatically operated system is added to reset the damper position. -- Comes With: NEMA enclosure, 10" x 10" x 6". Enclosure for Pneumatics 22" x 22" -- All (3) flanged connections are 22" x 22'" square. -- Construction: Damper assembly is fully bolted to provide solid, reliable operation. -- The power adapter for the independent power supply is extra.Overall dimensions: 60" long x 36" wide x 43" high.Improve the safety of your work environment & help comply with NFPA codes!

DUST-EX HSAG-24 Packaged Safety Solution for a 22"x22" (24" dia. round equivalent) Return Air Rated for 10,000 CFM. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap Valve (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel. One-Zone CP05 Control Panel 1 inlet, 1 outlet: UL698A Control Panel for use with NFPA 69 compliant Explosion Isolation Valves. Standard panel includes status lights, intrinsically safe circuit (1 Per Zone), monitored inputs (3 total), ability to add a secondary clean air isolation valve, output for system shut down and monitoring, drawings, installation instructions, NEMA 4 outdoor rated enclosure, UL and Canada UL listings. Allows for 120VAC or 24VDC input power. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 39" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) High Speed Abort Gate, EM-HSAG02-24, magnetic (24 VDC), 22" x 22" flanged inlet and outlet (24" round equivalent), control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 10,000 CFM / 3000 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe

LHI RFPR 102/10 MULTI-BLADE PANEL SAW: with 102" of usable width cutting capacity. Specifications: -- (1) 40 HP main arbor motor for 1/8" min. - 4-1/4" max. material thickness; min. panel length 30"; 102" of usable width cutting capacity. -- 12" Dia max. blade capacity; 1.25" minimum spacing between the blades; -- 3-15/16" Dia. arbor with 1-15/16" precision arbor bearings; -- Positive powered steel contact feed rollers with (8) Polyurethane drive rollers; fixed feed speed of 80 FPM. -- Includes (6) arbor collars - blades not included. -- Complete with:(2) 4" dia dust collection ports on top and (1) 8" dust collection port on bottom. Total recommended 2,200 CFM.Available Options: -- Blade Box & "Quick Change" Arbor Cart and Trolley $12,590.00 each -- Arbor Carts modifications to accept 12" dia. blades $700.00 each -- Single Point Height Adjustment $ 6,000.00 each -- "Quick Change" set up kit (includes belt guide, belt tensioner, and hydraulic arbor lock) $3,695.00 each -- Tandem 8000# capacity infeed Scissors Lift, 2 HP, 3 Phase, 230/460 Volt, 31" x 192" platform and cross bars for fork truck entry $14,495.00 each -- Tandem 8000# capacity outfeed Scissors Lift, 2 HP, 3 Phase, 230/460 Volt with 48" x 192" platform and beveled crossbars for fork truck entry and auto down indexing $16,390.00 each -- Drag Chain Feeder Conveyor - Roller conveyor transfers sheets to in-feed of saw and dog chains align and start the sheets into the saw feed rolls. Recommended with 102" wide machines, $18,800 Tooling Cost: -- Carbide Tip Blades 10" dia. x 40-tooth thin kerf blades $125.00 each -- Saw Blade Tooling Collars $125.00 eachOn average this machine will cut a bundle (42 sheets) of 3/4" Plywood. LVL, PB, MDF or OSB into narrow strips in 4 minutes or less.NOTE: PRICING DOES NOT REFLECT FACTORY'S 10% MATERIALS SURCHARGE

LHI 72" RFPR Wide Arbor Roll Feed Gang Panel Ripper with Custom 5' x 16' Automated Infeed -- Specifications: -- 30 HP Arbor Motor; 1/8" min. to 1-1/4" max. material thickness and 72" cutting width. -- 10" Dia. blade design cuts thru max. 2" thickness; -- 3-15/16" dia. arbor with 72" of usable width cutting capacity, min. panel length 30". -- 1-15/16" FAFNIR arbor bearings; with (8) steel feed rollers on 6" centers; fixed feed speed of 80 FPM -- 47-1/4" working height -- (1) Arbor Cart is included -- (2) 4" Dia. dust collection ports on top and (1) 8" dust collection port on bottom. Recommended 1,500 CFM Includes the Following Optional Items: -- 5-Strand powered Chain Deck; 12' long; arranged to feed 5' x 16' packages onto the Scissors Lift. Complete with controls for forward, reverse, and jog. -- 5-Sections of Gravity Rollers on Scissors Lift Deck -- 8,000 lbs. Infeed Tandem Scissors Lift with 5' x 17' Deck and 2-HP, 3-Phase Motor. Lift includes a backstop for initial alignment at the Rake Feeder -- (8) Polyurethane Rollers on 6" centers -- Variable Feed Speeds from 10 to 80 FPM. -- Rake Feeder for 16' long panels -- Auto-cycle for Rake Feeder. -- 6' Line Up Conveyor with Fence and Powered Pinch Roll Included Tooling: -- (36) Standard Saw Collars for Ripping -- (72) Standard 10" Sawblades for Ripping (Includes a spare set) -- (37) Standard Throat Plates for RippingQuick Setup Kit Included, Contains the Following -- Belt guide -- Belt Tensioner -- Hydraulic Arbor LockAdditional Arbor Setup Included. Contains the Following: -- Arbor Cart -- Cart -- Blade Box -- Arbor -- Bearings -- Sheave -- Throat Plate Rack -- (6) Throat Plates PRICE REFLECTS FACTORY'S 7% MATERIALS SURCHARGE ON $156,995, OR $10,990

LHI RFPR-72/16 "HEAVY DUTY" MULTI-BLADE PANEL RIP SAW (W/LOADING/UNLOADING): -- Specifications (1) 30 HP Main arbor motor for 1" min. - 5" max. material thickness;16" Dia max. blade capacity with 1.25" minimum spacing between the blades;Minimum panel length 30" with 72" of usable width cutting capacity.3-15/16" Dia. arbor with 1-15/16" precision arbor bearings;Positive powered steel contact feed rollers with (8) adjustable Polyurethane drive rollers;Variable feed speed to max 80 FPM.Available Options Include:Single point height adjustment for materials from 1" to 5" thickness using customer supplied 16" dia blades(note: Ripping widths can never be less than one-half the material thickness).(1) "Quick Change" arbor cart trolley and blade box for QC set ups.(12) Saw collars to attach the customer supplied 16" dia. diamond blades to the arbors(1) In-feed Scissors Lift with auto cycle controls(1) In-feed 6' conveyor with alignment fence and powered assist feed(1) Auto sheet feeder with auto cycle controls(1) Out-feed Scissors Lift with 4 x 8 roller top.Installation technical assistance for $125/Hr plus travel time and expenses, payable upon competition of services. NOTE:Quote is valid for 30-days;Quoted price is FOB, Factory;Customer is responsible for off-rigging cost at their facility;Customer is responsible for spotting the machine to its final resting place with adequate floor foundationCustomer is responsible for adequate electric, air & dust control supply upon technician's request:Warranty: 1-yr mechanical parts (electrical controls excluded);Delivery to Customer's facility is approx 17 weeks from receipt of funds;Quote assumes customer will deliver material for testing & run-off procedures (if required);NOTE: PRICING DOES NOT REFLECT FACTORY'S 10% MATERIALS SURCHARGE