VECTOR - REVOLUTION 180: CNC Contour Edgebander + Vector Vision UpgradeNumerically controlled automatic Edgebanding Machine: Precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the "X", "Y" & "Z" axis.Machine FeaturesBanding Unit: Simultaneously rotates on a high precision "C" Axis; AC Brushless Servo motors with: Digital drives & linear guides ensure high speeds & accuracy with a smooth acceleration & deceleration. -- NO PROGRAMMING required: Extremely simple changing from one tape size to another; Operator only has to make simple adjustments such as setting: Start position the glue height; feed the new width of tape; adjust the tape guide height. All else taken care of by the machine. -- Cartridge Glue System: Glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod; standard positions are: 16 mm (5/8"); 19 mm (3/4"); 25 mm (1.0"); 28 mm (1-1/8"); 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field"X" Axis 139.7" (3,550 mm); "Y" Axis 72" (1,830 mm); 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Min. external radius & 1.97" (50 mm) min. internal radius depending on the type of banding materials. 1 mm Min. banding material thickness; 3 mm max. banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- WorktablePhenolic worktable with: Embedded vernier scales in "X & Y" axes; allow simple & flexible positioning of 2-stage vacuum pods. Worktable allows single or pendulum processing with: (2) 48" x 72" (1,219 x 1,828 mm) Work zones for processing small to large parts. With average cycle times under (2) minutes, the Contour Edgebander consistently produces quality parts, including 360° lap joints.Workpiece is supported by: Vacuum cups sitting on a large, flat bed; enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with: 100 cbm/Hr Vacuum Pump. Pump is mounted inside the frame of the machine reducing noise & avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR "Revolution 180" Operating System is unaffected by panel position.Patented process is controlled by: Simple & intuitive interface that does not require CNC programming. -- Edge Banding UnitVECTOR "Revolution 180" uses: Cartridge & nozzle glue extrusion system, which is ideally suited to this Contour Banding application.Cartridge Glue Nozzle is: Closed system, which only heats the glue as it is used. Glue is not exposed to the atmosphere; there is no burning of the glue or discoloration & the original color of the glue & its properties are maintained.Another Glue Nozzle System benefit: Close proximity to the 1st pressure roller when slowing for corners; glue remains molten until pressed onto the panel by the 1st pressure roller. This is important when banding tight radii as the glue doe

VECTOR - REVOLUTION 180: CNC Contour Edgebander Numerically controlled automatic Edgebanding Machine precisely applies: ABS & PVC Edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along: "X", "Y" & "Z" axes.Machine FeaturesBanding unit simultaneously rotates on a high precision "C" axis; AC Brushless Servo motors with: Digital drives & linear guides ensure high speeds & accuracy with a smooth acceleration & deceleration. -- NO PROGRAMMING Required: Extremely simple changing from one tape size to another; Operator makes simple adjustments: Setting the start position & glue height; feeding the new width of tape; adjusting the tape guide height. All else done by the machine. -- Cartridge Glue System. Glue height set by: Positioning a pin in a hole in the index ring setting for the glue dosing rod; standard positions are: 16 mm (5/8"), 19 mm (3/4"), 25 mm (1.0"), 28 mm (1-1/8"), 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field"X" Axis 139.7" (3,550 mm); "Y" axis 72" (1,830 mm); min. - max. material thickness: 0.63" - 1.57" (16 - 40 mm).0.79" (20 mm) Min. external radius; 1.97" (50 mm) min. internal radius, depending on the type of banding materials. 1 mm Min. banding material thickness & 3 mm max. banding material thickness (NOTE: 1 mm PVC is not suitable for butt joints). -- WorktablePhenolic worktable with: Embedded vernier scales in "X & Y" axes allows for simple & flexible positioning of 2-stage vacuum pods. Worktable allows single or pendulum processing with: (2) 48" x 72" (1,219 x 1,828 mm) Work Zones for processing small to large parts.Average cycle times under (2) minutes; Contour Edgebander consistently produces quality parts, including 360° lap joints.Workpiece: Supported by means of vacuum cups sitting on a large flatbed; enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with a 100 cbm/Hr vacuum pump; pump is mounted inside the frame of the machine reducing noise & avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR "Revolution 180" Operating System is unaffected by panel position.Patented process controlled by: Simple & intuitive interface that does not require CNC programming. -- Edgebanding UnitVECTOR "Revolution 180" uses: Cartridge & nozzle glue extrusion system, which is ideally suited to this Contour Banding application.Cartridge Glue Nozzle. Closed system, which only heats the glue as it is used. Glue is not exposed to the atmosphere: Meaning no burning of the glue or discoloration; original color of the glue & its properties are maintained.BENEFIT: Glue Nozzle System is in close proximity to the 1st pressure roller; meaning: Even when slowing for corners, glue remains molten until pressed onto the panel by the 1st pressure roller. This is important when banding tight radii, as glue does not have an opportunity to chill before being presse

VENJAKOB Drying Oven -- VENJACOB Oven

This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

VERVILLE - 95-VP-438SE-CCW-35/125I: 4-Station Bagger complete Automatic Bag Placement and Bag SealerComplete Line was used for wood shavings only. The Line is in operation at the time of this write-up.The VERVILLE - VP438-CCW: 4-Station compression Bagging System designed for high-efficiency bagging operations.It features: High tubes of 125". Automatic plastic bag sealing Ability to handle bag sizes ranging from: 11" x 17" to 30" High.This System is often used in industries like: Biomass and Packaging. It also includes features: Oil tank heater and a Modem for remote monitoring.Bagging Capacity -- Handles bag sizes ranging from: 11" x 17" to 30" high. -- Automatic feature: Automatic plastic bag sealer for seamless operations. -- Height: System features: High tubes of 125 in., making it suitable for large-scale bagging needs. Additional Features -- Equipped with: Oil tank heater; modem for remote monitoring ensuring smooth and efficient performance.The control box is mounted on the side of the automatic Bagger with: ALLEN-BRADLEY Panel View 550 unit. -- Main 4-section Bagger: 125 " Tall. -- Main master control cabinet. -- Long 45° screw auger to feed from: Bottom of the Sifter to the top of the Bagger -- Master hydraulic tank & pump arrangement with all hoses. -- Full sealed bag auto. discharge conveyor belt & turning roller Conveyor. -- Sifter with: Canvas wrap cover. -- Screw Conveyor: Runs from under the outside dust Collection System rotary airlock: Drops the “good"; wood chips down to the 45° screw with “light dust" going out thru the Screw Conveyor into an open Dump Trunk outside.IMPORTANT ISSUESThe machinery requires a new Electronic Board & Computer with Software. Computer & Software is available, but it has to be programmed for this machine.Total HP: 75Price Includes: Loading on a Truck

VESTIL EHLT-2464-2-55 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 2,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 24" x 64". -- Lowered height 7", raised height 55". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VESTIL EHLT-4896-4-56 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 4,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 48" x 96". -- Lowered height 8", raised height 56". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

Biesse Viet S1 223 RKRT VN ( S1 223 2620) Sander2 Head 53" width cap Drum, Combiation ( Platen ) HeadHead configuration1st Head -- Steel Roller, Quick Set abrasive Thickness setting, Electro-pneumatic, "On/Off" movement2nd Head -- Kombi Drum/Pneumatic Sectional Platen -- Front roller on this combo head has Electro-pneumatic "On/Off" movement -- Electronic Segmented Platen controlled by reading bar at front of machine Equipped with & Features -- Inverter controlled. -- Can be used for wood, veneer and as a sealer sander -- Linear belt cleaner (Pneumatic) Feed Belt (54' wide) -- Vacuum Table with 3hp vac blowe -- Touch Screen control

VIET S1 223 2620 1350 mm (53.15") 2-Head Wide Belt Sander, with Combination HeadSpecifications: -- For wood, veneer, & sealing. -- Thickness cap. 3 mm - 160 mm (0.12" - 6.30"). -- Variable feed speeds 3 - 16 MPM (10 - 52 FPM).Equipped with: -- 1st Head: Grooved rubber-covered steel contact roll, 25 HP Motor with Brake & Inverter, Quick set abrasive thickness setting, Electro-pneumatic "on/off" movement. -- 2nd Head: "KOMBI KRT" Combination head, with Grooved rubber-covered steel contact roll, Electro-pneumatic "On/Off" movement, Electronic segmented platen with 42-Section Reading beam at infeed, & 15 HP Motor with Brake & Inverter. -- Segmented rubber infeed hold-down roll, Segmented rubber hold-down roll between heads, & Segmented rubber outfeed hold-down roll. -- 1,380 mm x 2,620 mm (54.33" x 103.15") Abrasive belts. -- 54"; W Vacuum feed belt, 2 HP Feed motor with Inverter, 4-Roll Infeed & outfeed extensions, & 3 HP Blower. -- Control, with Touchpad, LCD Display, & (2) Motor load meters.EQUIPMENT NOTE: Seller states belt sensor is faulty and needs to be replaced and contact rolls have some wear spots. Potential buyers are welcome to inspect under power.

VIET - S211 R+ KRT, 2-Head Wide Belt Sander43" Width. cap.: Drum and Combination head.Head Configuration:1st Head: 160 mm 6.3″ Helical grooved rubber drum. 25 HP motor2nd Head: 160 mm (6.3") Helical grooved rubber drum with a platen combination head., 25 HP motorSpecifications: -- Each heads are powered by a 25 HP motor. -- The heads can be programmed to pneumatically raise & lower along with the platen and do (3) sanding combinations (with the twist of a button). -- Digital height readout and a calibration unit to the left side of the conveyor. -- Conveyor speed is controlled via a variable frequency drive 2.5 HP . -- Max width: 43″. -- Max. height: 6-1/4". -- Variable speed conveyor belt drive from: 3 - 16 MPM (11 - 52 FPM).Equipped with & Features: -- Both heads are equipped with: 1,130 x 1900 mm (44-1/2" x 75"). -- Roller & pressure shoe holddowns. -- Pneumatic tension of sanding belts and feed conveyor. -- Load meter on main motor. -- Disc brake on main motor. -- Emergency stops front & back. -- Roller table extensions front & back.NOTE: This is an extremely low-hour 2012 BIESSE Viet S1 dual head 43″ calibrating Wide Belt Sander.

BIESSE - Viet Opera5 RRRF: Wide Belt Sander (4-Head) w/53" width cap.Head Configuration1st Head: Drum Unit The Roller Working Unit is: Characterized for the precision & effectiveness of the work it does.Main motor: 22 kW (30 HP).Drum: 240 mm; Steel Linear blower cleaning sanding paper A.S.S. (Air Saving System).Infeed pressure shoe.The pressure beam is used to guarantee the maximum precision when calibrating; flattens the deformed or thin pieces.Chromed anti-wear metal removable tips.Outfeed pressure shoe.2nd Head: Drum UnitMain motor: 18.5 kW (25 HP).Drum: 300 mm; 70 Shore.Linear blower cleaning sanding paper: A.S.S. (Air Saving System).Infeed pressure shoe.Outfeed pressure shoe.3rd Head: Drum UnitMain motor: 15 kW (20 HP).Drum: 300 mm - 40 shore.4th Head: Superfinishing UnitSuperfinishing Pad. The evolution of the pad unit (VIET patent, 1978). The pad unit has a "chevron belt" running between the pad itself and the abrasive belt that guarantees top-quality finishing and a longer performance to the abrasive.Main motor Inverter: 15 kW (20 HP).Pneumatic “Air Cushion"; pad: Pneumatic pad is the ideal tool to solve finishing problems.Contact insert for pneumatic pad made of: Steel + felt + graphite.Linear blower cleaning sanding paper: A.S.S. (Air Saving System).Infeed Pressure ShoeSpecifications -- Working width: 1,350 mm (53.15"). -- Constant Pass (Fixed Table): Heads adjust up/down by program. -- Working Height: 200 mm (7.87").Equipped with & Features -- Laser electronic positioning for working thickness. -- Motors with: AMP Meters. -- IPC Compact 15" Color Touchscreen Controller. -- Vacuum Table with: 7-1/2 HP Motor. -- Electronic System. IPC Control with: Feed speed: Up to 75 FPM. -- 50-Shore rubber Conveyor. -- Vacuum bed for: Short parts. -- Front & rear extension Rollers (2 each).

BIESSE/VIET - OPERA R 1.0: 36" W Robotic Denibbing Sander with Automatic Sanding Head Changer & Laser ScannerSpecifications -- Perfect for: 5-Part doors; end panels; inner side of profiles; rebates; window frames, etc. -- Sands panel with: Grain in any orientation. -- Smooths multilevel surfaces, as well as small internal corners. -- Sanding pad action similar to: Handheld Orbital Sander. -- Max. operating width: 36". -- Max. machinable length: 96". -- Max. machinable thickness: 60 mm (2.36"). -- Advance speeds: 2 - 10 MPM (6.6 - 32 FPM). -- Robot loading cap.: 12 kG (26.46 Lbs.)Equipped with: -- FANUC - M-3IA 12H, CNC Robot with: CONTROL FORCE System, which measures: Amount of abrasive pressure applied to panel & Dust Removal System. -- 8-Position automatic sanding head changer. -- FANUC "SYSTEM R-30IB A05B-2615-B082" CNC Control. -- FANUC "A05B-2255-C101#EGN" Remote teach pendant control. -- Head cleaning/dressing station. -- Panel cleaning brush. -- Antistatic bar. -- Rotating & linear blowers. -- 10' L x 900 mm (35.43") H Vacuum conveyor with: 4 kW (5.36 HP) Motor & (2) vacuum blowers. -- IPC Electronic control with 15";: Color touchscreen; manages all machine parameters. Complete with: -- 2016 CVM "TN/400-135": 53"; W x 12-1/2' L conveyorized Laser Scanner.Total Sander & conveyor dimensions: 282" x 127" x 94" H.Total Sander & conveyor weight: 4,125 kG (9,095 Lbs.)Sander dimensions: 127" x 120" x 94" H.Sander weight: 3,850 kG (8,488 Lbs.)Conveyor dimensions: 160" x 68" x 77" H.Conveyor weight: 275 kG (607 Lbs.)

VIRUTEX - EB 25: Hot Air EdgebanderFor preglued PVC, veneer and melamine laminate coil stock; 0.4 - 1.0 mm edge thickness; up to 65 mm panel thickness cap.; automatic coil & single edge strip feed.Equipped with: -- Thermostatically controlled hot air blower; 3,300 Watts for up to 500° C temperature; (2 - 3) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 15 FPM feed speed. -- Mounted on machine base with panel support table.Includes: Used tooling on the machine.

VITAP ALFA 21 CONSTRUCTION/LINE BORER21-Spindle boring head on 32 mm centers. -- Specifications: drills vertically from bottom up and head rotates to horizontal position for edge boring, head rotation is pneumatic with switch control. -- 2-3/4" Max. drilling depth, 2.5 HP - 2,800 RPM motor, pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size, max. workpiece width 31-1/2". -- Equipped with: Left & right side fences for construction boring, (2) pneumatic holddown clamps, line boring fence w/flip stops, pneumatic foot pedal control, magnetic starter & overload protection, and (1) set of quick-change chucks.

For pre-glued PVC, veneer, & melamine laminate coil stock; 0.4 - 1.2 mm edge thickness; up to 35 mm panel thickness cap., automatic coil feed. -- Equipped with: Electronically controlled temperature setting for hot air blower; 3,000 Watts for up to 650° F temperature; (1) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 16 FPM feed speed. -- Mounted on machine base with panel support table.

VITAP BLITZ CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:(1) CNC Controlled head assembly with rapid (side-to-side) traverse, assembly with boring, gluing & insertion unit, This Flexible machine is IDEAL for JIT or high production runs. -- Working Area:Useable working area "X" axis 36.2" (920 mm), "Y" axis 3.14" (80 mm), "Z" axis up to 1.57" (40 mm) material thickness with digital readouts -- BG & D Unit(1) 1 HP - 6,000 RPM horizontal drill motor; 0.47" (12 mm) Maximum drill bit dia. (1) Glue injector & (1) dowel Inserter with 1.57" (40 mm) Max. dowel lengthMachine is capable of processing dowel diameters from 6 mm dia x 25 mm long - 10 mm dia x 40 mm long dowels (currently setup for 8 mm dia dowels); -- Operator & Machine Control:CNC "Color Touch-Screen" Controller for function & simple part programming and program storage. -- Complete with: (1) 12" Dia. vibratory feed hopper, totally sealed electronically metered glue system with "Automatic" injector flushing; (1) 4.75 G (18 L) Glue tank & (1) 2.37 G (9 L) water tank;(4) Inclined vertical pneumatic hold-down clamps; Function selector control for boring only or doweling; Anti-slip table surface, Rack & pinion drive and centralized dust collection manifold.

VITAP - BLITZ: CNC Bore, Glue & Dowel Inserter -- Specifications(1) CNC Controlled head assembly with: Rapid (side-to-side) traverse; assembly with boring, gluing & insertion unit This "flexible" machine is IDEAL for JIT or high production runs. -- Working AreaUsable working area: "X" Axis 36.2" (920 mm); "Y" axis 3.14" (80 mm); "Z" axis up to 1.57" (40 mm) material thickness with digital readouts. -- BGD Unit(1) 1 HP - 6,000 RPM Horizontal drill motor; 0.47" (12 mm) max. drill bit dia.; (1) glue injector & (1) dowel Inserter with: 1.57" (40 mm) Max. dowel length.Machine capable of processing dowel diameters from: 6 mm Dia. x 25 mm long - 10 mm dia. x 40 mm long dowels (currently setup for 8 mm dia. dowels). -- Operator InterfaceCNC "Color Touchscreen" Controller for: Function & simple part programming and program storage. -- Complete with: (1) 12" Dia. vibratory feed hopper; totally sealed electronically metered glue system with: "Automatic" injector flushing; (1) 4-3/4 G (18 L) Glue Tank & (1) 2.37 G (9 L) water tank.(4) Inclined vertical pneumatic holddown clamps; function selector control for boring only or doweling; anti-slip table surface; rack & pinion drive; centralized dust collection manifold.

VALPATO LBK-150-ST 1 Feed Through Profile SanderTECHNICAL FEATURES: An added small needle type drum sander can be fitted with drum sanding aggregates of 25, ­30, ­35,­40, ­45 ­50 mm diameters which can be used for tighter curves and smaller radius sanding requirements. Storage compartments (2 in total) are located on each machine extremities, these are easily accessible and can be used for sanding belts and various tooling storage. Sanding belt motor power: 3 Kw Abrasive head motor power: 1.5 Kw Oscillation motor power: 0.38 Kw Feed motor power: 0.75 Kw Motor power for electrical adjustment of sanding group: 0.19 Kw Machine voltage: 480/3/60 Full Load Amps @ 480V: 15A Compressed air: Not required Dust collection requirement one (1) only 6" (150mm) port: 950 CFM Sanding belt speed: 14 Mt/sec Variable speed of the belt: from 5 to 25 m/min Sanding belt dimensions: 150 x 2640 mm Height of working table: 930 mm Dimensions of front working table: 1980 x 250 mm Machine dimensions: 2500 x 900 x 1600 mm Net weight: 1000 KMAIN FEATURES: User friendly PLC touch screen control panel is accessible from 360° by the operator, the control panel is centrally located on the infeed end of the machine. Factory installed variable feed drive (VFD), enables machine to run from 5 M/Min to 25M/min (+/­ 80 ft/Min). The entire sanding plenum rise and fall is motorized, it can be adjusted vertically in height to utilise the full height/width of the sanding belt. An oiling unit ensure long life of sanding plenum rise and fall master cylinder.

Volvo L90H Wheel LoaderSpecifications: Static tipping load at full turn: 22,265 lbs Bucket capacity: 2.9 - 9.2 yd³ Log grapples: 1.6 - 2.9 yd² Operating weight: 31,968 - 38,140 lbs Breakout force: 31,470 LBF Engine: Volvo D6J Max power: 1,400 - 1,900 RPM, ISO: 14,396 gross, 184 HP, ISO: 9,249, SAE J1349 Net, 184 HP Max torque: at 1,400 RPM, ISO 14,396 gross 689 LBF Ft., ISO 9249, SAE J1349 Net 689 LBF Ft. Tires 20.5R25 600/65R25Approx 4900 Hours

VOLVO - L70G: Wheel LoaderVOLVO "L70G" is a versatile wheel loader that got the job done. Specifications: -- Engine: "D6H TIER 4H 171" HP Turbocharged. -- Max. speed: 28.6 MPH. -- Raise time: 5.1 Sec. -- Dump time: 1.2 Sec. -- Lower time: 2.7 Sec. -- Max. bucket capacity min.: 2.4 cbm. -- Hours: 13,560.Equipped with: -- Heat & A/C Cab. -- Air ride. -- Quick hitch.Everything works as it should and ready for work.We can provide financing and assist with delivery to your location.