SANI-TECH -, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

Schneeberger 9 Sculptor Profile GrinderSwiss Made, Schneeberger Automated High Precision Grinder for Finger Joint, router bits, saw blades, straight and milling Cutters. Specifications: -- Grinding Motor: 1,500 - 3,000 RPM. -- Cooling Pump: 2,800 RPM. -- Grinding Wheel Speed: 3,000 - 6,000 RPM. -- Grinding Wheel Diameter: 50 - 200 mm. Grinding Wheel Bore: 30 mm. -- Cross Travel of Grinding Wheel: 200 mm. Vertical Travel of Grinding Wheel: 400 mm. -- Grinding Head: Swivel-able. -- Worktable Travel: 400 mm. -- Coolant Capacity: 25 liters.Dimensions: 1,226 mm length x 1,160 mm width x 1,180 mm height; Weight - 320 kG.10" Width cap., 11.5" dia., max. profile depth 5.5", radial clearance angle up to 35ø, lateral clearance angle up to 15°Equipped with & Features; -- 2 HP - 1,500 RPM motor, variable grinding speed 2,000 - 4,000 RPM, three-sided full jet cooling. -- All std. grinding equipment for HSS grinding, 1-1/2" spindle arbor, (2) wheel flanges, (1) knife holder, and dresser.

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

SCM PRATIX S-12-B FLAT TABLE MACHINE (W/ATC/BORING): -- SpecificationsSingle 4' x 8' traveling "Bridge Gantry" and stationary aluminum dual-vacuum table with: "MATRIX" square grid pattern for fixturing parts.Grid pattern allows use of vacuum pods or closed cell rope gasketing material and use of spoil-boards for "nested base machining".Part location pop-up pins mounted on the table perimeter. -- Working field:"X" Axis is 98" (2,486 mm); "Y" axis is 49.4" (1,255 mm); "Z" axis stroke is 9.8" (250 mm); max. material thickness 5.9" (150 mm). -- Positioning Speed:"X" & "Y" Axis 115 FPM (35 MPM), "Z" axis at 82 FPM (26 MPM); closed loop AC Servo drive system.High precision "Rack & Pinion" system in "X" & "Y" axis & ground ball screws "Z" axis; all axes ride on extra-large precision profile linear guideways. -- Boring Unit:3 HP (2.2 kW) - 6,000 RPM motor; (7) vertical spindles on 32 mm centers, (5) spindles in "X" axis & (2) spindles in "Y" axis. -- Machining:(1) 9 HP (6.7 kW) Air-cooled electro-spindle with HSK F63 adaptor; variable spindle speeds from 1,500 - 24,000 RPM.(1) 7-Position ATC tool rack mounted to the machine base RH side. -- Operator & Machine Control:PC Front-End with: "XILOG Plus" + Windows "XP Pro" Operating System; 17" high resolution LCD; ergonomic keypad.USB Ports, serial ports RS-232 & RS-242 & Ethernet adaptor; programs can be transferred via disk or downloading by wire is possible.All computer components are mounted on a mobile stand.XILOG Plus Offers incredible list of functions from: (a) Auto-diagnostic to (z) zooming; controlled acceleration & deceleration, encoder feedback, dynamic tool correction via PLC due to active tool wear using space-and-time criteria. -- Additionally Equipped with:Onboard mini-CAD with built-in programming for writing: Circles, ellipses & angles with only a few keystrokes.Onboard cycle optimization, onboard calculator, mirror-imaging, and repeat imaging. -- Complete with:(2) 150 cbm Vacuum Pumps; safety enclosure around the spindle carriage. Tool length measuring device.(1) Universal remote Pendant; 7" color display allows for the effective management of all machine functions from manual Jog Mode to loading & execution of a program. The pendant is fitted with a USB port to allow quick load & setup of new programs.Safety "bump-stop" bumpers; emergency stop rope, doc's & manuals. -- Actual Model: SCM PRATIX S-12-B

SCM OLIMPIC K360 EDGEBANDER (W/PRE-MILLING):Specifications -- Edge Capacity: 0.3 - 3 mm (0.012 - 0.118"); for coiled edges: 0.3 - 6 mm strips with: 6 x 60 mm kit included; dia. coil holder plate: 780 mm (31"). -- Panel Capacity. Min. width: 90 mm; min. length: 140 mm (3-1/2" & 5-1/2"); panel thickness min./max.: 8 - 50 mm (3/8" - 2") & max. 60 mm (2.4") with 6 x 60 mm kit included.Equipped with: -- Adjustable Infeed Fence: Manually preset with digital indicator; pneumatic in/out positioning. -- Premilling Station - "RT-VP": Spindles: (2) x 2.0 HP - 19,000 RPM; (1) PLC controlled jump action; diamond cutterheads. -- Automatic Strip & Coil Feed Magazine: For straight edges; 3 mm guillotine for coils. -- Gluing Station for EVA (Hot Melt) with: Teflon-coated glue tank; quick disconnect to change glue tanks fast if needed; Heat-up time approx. 10 Min. Includes 1.5 kG glue pot instead of standard. -- Pressure Section: Manual digital positioning, (3) pressure rollers: 1st Larger; Teflon Coated and powered. Workstations -- End Trimming Station - "K2". Front & rear: (2) x 1/2 HP (included extra); 12,000 RPM Motors mounted on THK guides; swivels 0° - 15°; rapid setup between straight & angled cutting with the automatic swivel cylinder.Automatic positioning for (3) cutting modes: Straight, chamfered, and radius of thick edges. -- Top & Bottom Trimming Unit - "R-K". Remote (via control panel) pneumatic positioning for (3) settings: Flush/bevel/radius trimming; (2) x 0.7 HP - 12,000 RPM motors with precision digital indicators for quick setup. -- Top & Bottom Profile Scraping Unit. Manual preset with: Digital indicators; large dia. copy wheels for max. accuracy; pneumatic in/out positioning. -- Buffing Unit - "SP-V": Top/bottom; (2) x 1/4 HP - 2,800 RPM Motors; tilting up to 12°; cleaning & polishing of edges.Controls -- ORION - "1" Plus: Controller. Fixed at infeed of machine; soft keys; graphics; 4" LCD display panel.Handles most machine setup functions & workstations; machine automation by PLC function; encoder positioned in the panel feed track pinion; diagnostics for a quick solution to many errors; process statistics data: Number of pieces/edges and track feeding.Features & Complete with: -- Feed speed: 36 FPM Fixed; (1) x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units; manual adjustable holddown pressure beam; full sound enclosure cover; outboard panel support. -- Overall dimensions: 3,600 mm (142") x 900 mm (36") x 1,600 mm (63"); approx. weight: 997 kG (2,200 Lbs). -- UL/CSA approved version.

SCMI MINI MAX - Formula S 2: Sliding Table SawSpecifications & Features -- 128" Cutting cap. w/standard scoring saw and carriage; 5 HP motor; stop on fence for cuts extendable to 128"; 50" cutting width w/ rip fence.Equipped with: -- 14" Main blade; 4-1/2" scoring blade; 4-1/2" max. blade cutting height at 90°; 3-1/2" max. blade cutting height at 45°. -- 4,000 RPM Main blade speed; 8,500 RPM scoring blade; 90° - 45° blade tilting.

SCM ACTION FL 2500 CASE CLAMP (SEMI-AUTOMATIC): -- SpecificationsMax. standard working dimensions: 2,500 mm (98.4") Wide x 1,250 mm (49.2") high x 800 mm (31-1/2") depth. -- Min. standard working dimensions: 250 mm (9.8" Wide x 250 mm (9.8") high x 150 mm (5.9") depth. -- Working height: 508 mm (20"). -- Vertical pressing force: 15 KN (3,372 Lbs.).Features -- Full top & bottom platen for maximizing pressing PSI on the box. -- Rack & Pinion guides at all (4) corners of the top platen & side pressure to keep the top platen parallel and the side pressure square. -- Sizes of box can be input for efficient cycle control when running repetitive box closings. -- Machine can also find the size of the box, so all the Operator has to do is open the Clamp to a size larger than the box to be clamped. -- The vertical & horizontal pressure is adjustable according to the type of furniture to be assembled. -- Machine is equipped with: (3) Side pressure bars & able to sequence different furniture pieces without manual intervention. -- Pressure supplied by infinitely adjustable brushless electro-motors.Complete with: -- 5.7" Touchscreen panel with: Software by CPC in order to program cycles. -- Rack & Pinion system, brushless motors. -- Front & rear photocell barriers. -- Actual Model is: SCM CPC ACTION FL 2500

SCM TECNOMAX SC/4 WS 8-1/2' Sliding Table SawSpecifications: -- Max. depth of cut with 315 mm (12.40") Dia. blade: 100 mm (3.94") at 90°, 70 mm (2.76") at 45°. -- Main saw: 3.6 kW (4.82 HP) Motor, Blade dia. 315 mm (12.40"), Arbor tilt 0° - 45°, Blade speed 4,000 RPM. -- Scoring saw: Blade dia. 100 mm (3.94").Equipped with: -- 11-1/2"; x 102"; x 35-1/2"; H Aluminum sliding table, 840 mm (33.07") LR Fixed table. -- Manual raise, lower & tilt. -- Mechanical digital tilt indicator.Complete with: -- 39-1/4"; L x 3-1/2"; H Rip fence, with 51" Cutting width cap. & Cam-locking. -- 650 x 1,100 mm (29.59" x 43.32") Squaring frame, with Crosscut fence with 1,800 mm (70.87") Cutting cap., (2) Flip stops & Sliding outrigger support.Actual model is SC/4 WS-N.

SCM MINIMAX - FORMULA S1, ...Sliding Table SawSpecifications: -- 120" Cap. with: Scoring; 9 HP main motor & belt driven scoring blade; -- Manual tilting of the arbor 0° - 45°; Manual raise-and-lower of the main blade; -- 50" crosscut capacity with a movable fence.Features: -- "Easy-Set" scoring adjustment; heavy cast iron trunnion; 12" main saw blade dia. with 1" Arbor, 110 mm scoring blade dia.; -- Max. cutting height 3-1/2" at 90° & 2-3/4" at 45°; 1-speed arbor; 8,000 RPM on scoring blade. -- Complete with: 4" Main dust extraction outlet, miter fence & crosscut fence assembly with (2) flip stops.

SCM TECNOMAX - SC/4 WS, ...8-1/2' Sliding Table SawSpecifications: -- Max. depth of cut with 315 mm (12.40"); dia. blade: 100 mm (3.94") at 90°; 70 mm (2.76") at 45°. -- Main saw: 3.6 kW (4.82 HP) Motor; blade dia. 315 mm (12.40"); arbor tilt 0° - 45°; blade speed 4,000 RPM. -- Scoring saw: Blade dia. 100 mm (3.94").Equipped with: -- 11-1/2"; x 102"; x 35-1/2"; H Aluminum sliding table; 840 mm (33.07") LR fixed table. -- Manual raise, lower & tilt. -- Mechanical digital tilt indicator.Complete with: -- 39-1/4"; L x 3-1/2"; H Rip fence with: 51" Cutting width cap. & cam locking. -- 650 x 1,100 mm (29.59" x 43.32") Squaring frame with: Crosscut fence; 1,800 mm (70.87") cutting cap.; (2) flip stops & siding outrigger support.NOTE: Saw is deinstalled as pictured in Photo #2. - Photo #1 shows Seller's other Saw, which is also available to purchase (EXF # PS-011935). Both Saws are one serial number apart. Seller confirms that all machine components are present.

SCM SI 350 N - 10-1/2', ...Sliding Table SawSpecifications: -- Cutting length 3,200 mm (126"); max. depth of cut: 118 mm (4.65") at 90°; 81 mm (3.19") at 45°. -- Main saw: 6.6 kW (9 HP) Motor; blade dia. 250 - 350 mm (9.84" - 13.78"); arbor dia. 1"; arbor tilt 0° - 45°; blade speed 4,000 RPM. -- Scoring saw: 0.75 kW (1 HP) Motor; max. blade dia. 120 mm (4.72"); arbor dia. 20 mm (3/4"); blade speed 8,500 RPM; external scoring blade adjustments.Equipped with: -- 14-1/4"; x 126"; x 35-1/2"; H Aluminum sliding table; 630 mm (24.80") x 1,040 mm (40.94") Fixed table. -- 2-Position table lock mechanism; manual raise, lower & tilt. -- Mechanical digital tilt indicator. -- Pivoting blade guard with dust outlet.Complete with: -- 47-1/4"; L x 3-1/2"; H Rip Fence with: 67" Cutting width cap. -- Crosscut Fence with: 84" Cutting cap.; (2) flip stops & Sliding outrigger support.

SCMI SANDYA S300 RCS 110 DUAL HEAD WIDE BELT SANDER43" Width capacity, (1) contact roll & (1) combination head with contact roll & segmented platen.Head Configuration1st Head : 5-1/2" diameter steel calibrating contact roll2nd Head : 5-1/2" diameter rubber covered contact roll and adjustable segmented finishing platen.Specifications -- 0" to 6.69" thickness capacity via motorized bed adjustment with auto set up device. -- Abrasive Belt dimensions 43" X 75" -- Rubber coated pressing rollers before and after working unit -- 1 HP Inverter variable speed feed unit. -- Feed speeds 10 - 60 FPMEquipped with and Features -- Y-Delta two-stage reduced voltage starter on 18 HP main motor -- 2 Roller Infeed and Outfeed table extensions -- Automatic Electronic Table Positioning Device -- Adjustable sanding drum and pad position for micro precision adjustment -- Electronic digital thickness readout of work table position -- Powered table lifting by means of (4) heavy duty motor and lifting columns double fastened at both top and bottom of the lifting columns to provide exceptional table stability -- Electronic tracking of abrasive belt -- Automatic feed mat tracking -- Pneumatic belt tensioning with center fulcrum to compensate for tapering of abrasive belt

SCM SANDYA 10/S M2 2-Head Wide Belt SanderHead Configuration1st Head: 7" Diameter Spirally-grooved steel contact roll, 20 HP Motor.2nd Head: Combination head, 7" Diameter Spirally-grooved rubber-coated contact roll, Finishing platen with Electronic sectional pad with EPICS System, 3-1/2" Steel contact roll, 13 kW (17-1/2 HP) Motor.Specifications: -- 4.5 - 9 m/min (15 - 30 FPM) Variable feed speeds, -- Part thickness 4 mm (0.2") to 170 mm (6.7"). -- 43" W x 103" L Abrasive belt, Electronic sanding belt tracking & Pneumatic belt tensioning. -- 34" H Natural rubber feed belt,Equipped with & Features -- Automatic thickness adjustment, Automatic feed belt tracking & Tensioning, -- Motorized rise & fall of working table, -- Part thickness & Conveyor belt speed LED readout, -- Infeed safety bar for operator protection and oversized parts. -- 3" Diameter Entry & exit rolls, 13" L 2-Roll Infeed & Outfeed extensions with 2" Diameter Rollers & Manifold. -- Unopened box of (10) KP520 100 Grit Belts (Purchased for $500).Dimensions: 88" L x 86" W x 90" H.Weight: 4,440 Lbs.

STEINEMANN OSUS NOVA 160/6 K-FS/NS-OPTIMAT Top and Bottom Calibrating Sander(6) heads consisting in 2 machines, first machine top/bottom opposed head. Secoind machine (4) head with Combi and finishing platenFeatured: -- 2-Head K, (1) top & (1) bottom; both heads directly opposed. for calibrating -- (4) head FS/NS top/bottom first Combi head, second finishing platenSpecifications:First machine Calibrating Sander: -- Top/bottom opposed single head -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on K head 34 M/sec. (6,667 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- 100 HP motor each head. -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine only Second Machine Finishing Sander: -- Top/bottom (2) head each as Combination drum/platen and finishing platen -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on FS head 22 M/sec. (4,330 SFM) -- Cutting speed on NS head 22M/sec. (4,330 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- No motor installed -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine Not included: -- infeed and outfeed conveyor -- Conveyor between the machine -- “all the control wiring goes into a cabinet that is separate on each machine. That is just the wiring for the sensors and solenoids for braking and belt tracking stuff. There are no motor controls with these so there are no starters included. The 2 head comes with (2) 150 HP motors and the 4 head has no motors on it. In order to make these operational you would need a PLC and HMI to run the controls and motor starters and would need to buy motor controls