SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location, refurbished added installation.

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

SPROUT Rotary Drum Dryer with Gas Burner;Complete with the following components: -- 7.5 Ft. x 24 Ft. Steel Rotary Dryer Drum. -- Natural Gas Burner (may be converted to LP) with 13.5 Ft. Refractory Lined Furnace Tube. -- Belt Drive with Gear Reducer and Electric Motor. -- Trunnion Bases complete with Forged Trunnion Wheels. -- Forged Trunnion Tracks (weld-on style) ...look like new. -- Vertical drop material Inlet Transition with Side Access Door. -- Rated for approx. 2 TPH water evaporation or about 4.5 TPH wood sawdust input. -- OPTIONAL ITEMS: &#9679 Receiving Bin with Airlock and Screw discharge Conveyor. &#9679 Material Input Screw Conveyor. &#9679 Main Fan.

SQUARE D - 75T3H, ...75 KVA, 480 - 208 V, 3-Phase Autotransformer Specifications: -- Intended for power, heating, and lighting applications. -- Enclosure Rating: NEMA 2. -- Multi-Tap (432 - 504 V) Primary 480 V (Delta); Secondary 208Y / 120 V @ 60 Hz ventilated. -- Aluminum windings. -- cULus Listed. (2) Available; price per unit. - Make offer for both!

SSI Model - 1000-E, Slow Speed, High Torque ShredderSpecifications: -- 50 HP Motor; twin shafts; 40" x 25" ChamberIncludes: -- Stand, feed hopper; controls

STAHL - PTB 01 ATEX 1016, ...Single Sheet Panel Turner.Specifications: -- 40" X 144" Capacity. -- Hydraulic pump for the rotation. -- The turning cycle is to match Finishing Line Speed running between 5.5 to 6 MPM.NOTE: Came out of a Finish Line.

STANMAC "MC/WB 300" Vacuum Coater; 3- or 4-sided coating. -- 8" Max. width x 2-1/4" max. height cap.; 24" min. length. -- Substrate enters vacuum chamber via 6" conveyor belt and passes through the coating; variable speed from 30 - 200 FPM as the substrate leaves the chamber. -- Negative pressure in the chamber keeps excess fluid inside resulting in 100% transfer efficiency; coating runs through several filters and is sent back to the reservoir for use again. -- Equipped with: (1) 15 HP Regenerative vacuum producer that holds fluid inside vacuum chamber; 15-gallon capacity reservoir; stainless steel vacuum chamber with adjustable substrate holddowns & guides. -- Equipped with: Air operated diaphragm Recycling Pump, high capacity fluid filter, separation tower with stainless baffle, and filtering system. -- Heavy gauge steel construction and free-standing control/operator panel. -- 100% Transfer efficiency; coating thickness controlled with a modulating valve & vacuum pressure gauge. -- Uses waterborne coatings for stains, primers, sealers, basecoats, topcoats, and even fungicides; can be used to coat most solid materials regardless of shape or length.

STANMAC SPRAY 300 Moulding Sprayer The Stanmac "Spray 300" is ideal for linear profiles in a wide range of materials and capable of utilizing both waterborne and solvent-based coatings including stains, paints, and lacquers.Spray guns are automatically timed for the start and stop of the spray cycle to ensure the best spray efficiency. The overspray is captured by the spray trough and can be recovered while atomized spray is captured by fiberglass media and clean air is exhausted from the spray cabin.Can be fitted with spray gun packages to include conventional, air-assisted airless, and airless to suit your requirements.Specifications: -- Workpiece max. width: 12"; -- Workpiece min. length: 30" -- Feed Speeds: 30 - 150 FPM -- Feed Motor: 0.5 HP -- Extraction Fan: 3.0 HP -- Number of Spray Guns: 3 -- Recovery Troughs 1 -- Spray Gun Trigger: Electronic Switch -- Piece Counter: Digital -- Filter Media: Replaceable fiberglass media

STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER:: -- Specifications:(1) Spindle with 12 HP - 3,600 RPM motor, 60" max. crosscut cap., material thickness 0.25" - 1.125". (1) Internal 60" Stroke Tape Applicator Station. -- 96" Stroke Servo Motor Driven Rear Pusher Fence (Full 60" Rear Table Width), 96" Long x 20" Front Table with 5 Digital Manual Stops. -- Rear Fence Movement, Cutter forward Speed Cut/Tape Stroke and All Controls for Start/Stop, On/Off, Axis position Displays on 10" Touch Screen Panel HMI. -- Grooving Head up & down movement via pneumatic cylinder with linear rail & linear bearings, depth fine adjustment with special threaded adjustable unit. -- Carriage cross-travel powered by a 3 HP hydraulic motor (4GPM), driven ball screw with linear rail & linear bearings; feed rate from 0 - 40 FPM; Heavy Duty welded frame construction. -- Complete with:Safety guards and cutter guards; pneumatic support fence; (1) heavy-duty in-feed/out-feed roller tables. Available Options at additional cost:ACCESSORIES, TOOLING AND TAPE "CHOOSE AND ADD TO MACHINE BASE PRICE" Cove Corner Plug Jig $575.00 ea. Brazed Carbide 90 Degree Cutter for up to 1/2" Solid Surface $745.00 ea. Please specify the Material Brazed Carbide Cove Backsplash Cutter for 1/2" Solid Surface $1,265.00 ea. Please specify 3/8" or 1/2" Radius Brazed Carbide 90 Degree Cutter for up to 3/4" Wood Materials $940.00 ea. 90 Deg. Insert Cutter for up to 1/2" Thick Material (Body Only) $1,265.00 ea. Requires Below Inserts90 Degree V Insert for up to 1/2" Thick Material, $32.00 ea. Minimum of 12 Inserts Required $384.00 Carbide Insert Cove Backsplash Cutter Head for 1/2" Material (Body Only) $1,590.00 ea. Please specify 3/8 or 1/2 RadiusRequires Below Inserts 3/8" Cove Radius Insert for 1/2" Thick Material $42.00 ea. Minimum of 12 Inserts Required $504.00 3/8" Double 45 Degree Insert for 1/2"Thick Material $42.00 ea. Minimum of 12 Inserts Required $504.00PCD Diamond 90 Degree Cutter for up to 1/2" Thick Material $3,485.00 ea. PCD Diamond Cove Cutter with 1/2" Radius for 1/2" Thick Material $5,645.00 ea. Roll of VAC2MG, 2" (50mm) wide 1025y (937m) long Roll V Groove Tape $245.00 ea. Minimum of 3 Rolls per order = $735.00 -- Actual Model is STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER:

STAR V MACHINERY SLG-2000 36 LINEAR V-GROOVER: -- Specifications:Working table dimensions are 120" long x 36" wide; Working width from 6" - infinite" (152 - infinite mm); Working length from 20" - infinite (508 - infinite mm); Working thickness from 0.25" - 1.15" (6 - 29 mm).Maximum throat clearance for linear & crosscuts is 14.5"/24.5" (355/622 mm). -- Equipped with: (2) Independent, 10 HP - 3,600 RPM Saw Motors with "servo" control adjustment in "Y" axis & manual "Z" axis adjustment.30 mm Dia. Arbor x 76 mm (3") clamping length to accommodate wider cove backsplash, triple-fold profiles, or using it for hogging and finish cut; 9.25" (235 mm) max. Cutter-head dia.1-Saw motor is mounted on the front & 1-Saw motor is mounted on the back of the 8" x 12" x 1/2" heat-treated steel heavy-duty overhead support beam.Side-to-side head travels via linear rails & bearings, manual head height adjustment via linear rails & bearings. -- Feeding System:(1) 3 HP Variable speed drive belt system with "servo" height adjustment; Feed rate from 0 - 45 FPM (12 MPM), belt feeder moves workpiece on a precision "aluminum" roller table; -- Tape Applicator: (2) Automatic Tape Applicators with "servo" adjustment, according to the Saw motor position in "Y" axis. -- Operator Interface:10" HDMI Touch Screen Display for Start/Stop, On/Off, Feed Speed & Axis Position. -- Complete with:; Safety guards and Cutter guards. Anti-Kick-back Device. Emergency Shutoff line. Dust collection requirements 4,200 CFM, collector outlets on cutter guards 5" in dia. -- Actual model# is STAR V MACHINERY SLG-2000.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5h VANTEDGE MM 6.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + EVA & Polyolefin Adhesive ready. Specifications: Working Capacity: Edgebanding thickness 0.4 - 3 mm coil stock capacity & 10 mm strip capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 60 mm (0.39" - 2.36"). Tape and Panel Infeed System: 750 mm Coil support table; adjustable track feed speed 14, 16 & 20 MPM (66 FPM). Heavy-Duty large solid polished steel panel infeed fence guide system. Large industrial digital adjustment for the Premill panel material removal amount. Top Pressure Beam Adjustment: Automatic adjustment from the PLC control; pneumatic Pop-Up Stop system. Red LED panel feed indicator light for correct panel spacing. Equipped with: Dual 3 HP Pre-milling motors w/diamond cutter heads; pneumatic "JUMP In/Out function. Misting unit prior to Pre-milling; large dual dust housing ports to help clean the Pre-milling system. Quick change Glue Reservoir for EVA & PO glues; Pressure Section/Infrared Heat Lamp System. Heavy-Duty automatic shear type Guillotine with: "Auto-Set" automatic intervention for strip & coil materials. (4) Pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness. (1) Rubber infeed Tape Roller, (1) metal infeed Tape Roller; direct Universal Drive system - NO Chains. Teflon-coated glue pot; digital thermostats with automatic kick down when the machine is in idle mode. Workstations: End Trimming Unit: Dual 0.5 kW (0.67 HP) high frequency End Trim motors on precision "Auto Lube" Linear Guideways; 90° to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions; thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: Dual High Frequency 0.65 kW (0.75 HP) motors with Combi Finish insert tooling.Top Servo driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy System. (2) Independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: Top, bottom & side Copy Wheels to properly follow your panels edge. Panel Nesting System: Triple Copy System for panels with blind dados & hinge cup holes. Digital adjustment for fine-tuning the unit to the proper tape thickness. Flat Scraping Unit: Large copy wheels. Buffing Unit: Top & bottom Buffing Unit; 0.5 HP (0.37 kW) - 2,800 RPM motors; units tilt 0° - 30°. Dual Hot Air Blowers: To re-embellish edge materials. Operator Interface 10" Color touchscreen PLC with swivel Control Panel. The PLC controls all working units & the adhesive thermostats with 1-touch icon programmable selections. Photo indicator alarms to easily troubleshoot errors/issues. Complete with: I

VECOPLAN VAZ 145/250 SINGLE SHAFT SHREDDERSpecifications; -- 575v 3 Phase --Hopper opening: 57 x 98.58 in. --Rotor width: 98.58 in. --Rotor Diameter: 14.56 in. --Rotor speed: 200 rpm --Main Drive- Electric motor with power belt drive --Gear ratio: i=5 --100 hp --Motor current: 192 A --Dimensions:- Shredder: 184"L X 141"W X 108"T- Chute: 160"L X 128"W X 76"T- Panel: 73"L X 50"W X 25"T

VECOPLAN RG 70/200K Shredder with Steel Belt Conveyor & Dust CollectorSpecifications: -- Hopper Opening: 70″ x 80″ -- Hopper Volume: 4 – 6-1/2 Cubic Yards -- Main motor: 200 HP -- Rotor diameter: 20″ -- Number of cutters: 84 (triple row) -- Size of cutters: 40 mm x 60 mm -- Screen size: Holes 2″ -- Rotor speed: 145 RPM -- Rotor diameter: 20″ -- Hydraulic Feed Ram: 10 HP - 2-Speed -- Throughput: 2,000 – 28,000 Lbs/HrEquipped with: -- 10 HP Motor Dust Collector -- 48″ W kW SCHMIDT Shredder Infeed Conveyor w/ 20′ pit section

VECOPLAN RG 42-40 SINGLE SHAFT SHREDDERSpecifications; -- 40 HP MotorVecoplan ShredderModel: RG 42/40 XL PVYear: 2007Motor: 40 HP, 460V, 60HZRPM: 1465Feed Opening: 42" x 48"Blades on rotor: 27Weight: 3,700 lbs

VECOPLAN RG52/60 SINGLE SHAFT SHREDDER Includes Box Dumper and ConveyorsSpecifications: --In Feed Opening: 52″ x 58″ --Rotor Length: 52″ --Rotor Diameter: 15″ --Hopper Volume: (4) Cubic Yards --Cutters: 37 --Drive Motor: 60 HP --Box Dumper / Table --Infeed Conveyor --Discharge Conveyor for Gaylord Box Loading

VECTOR REVOLUTION 180 CNC CONTOUR EDGEBANDER + Vector Vision Upgrade: Numerically controlled automatic Edgebanding Machine precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the "X", "Y" & "Z" axis.Machine Features:The banding unit simultaneously rotates on a high precision "C" axis; AC Brushless Servo motors with digital drives and linear guides ensure high speeds & accuracy with a smooth acceleration-and-deceleration. -- NO PROGRAMMING required, extremely simple changing from one tape size to another, the operator only has to make simple adjustments like setting the start position, the glue height, feed the new width of tape and adjust the tape guide height. All else is taken care of by the machine. -- Cartridge Glue System, glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod, standard positions are, 16 mm (5/8"), 19 mm (3/4"), 25 mm (1.0"), 28 mm (1-1/8"), 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field:"X" Axis 139.7" (3,550 mm), "Y" axis 72" (1,830 mm), 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Minimum external radius & 1.97" (50 mm) minimum internal radius, depending on the type of banding materials. 1 mm Minimum banding material thickness & 3 mm maximum banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- Work Table:Phenolic worktable with embedded vernier scales in "X & Y" axis allows for simple & flexible positioning of 2 - stage vacuum pods. The worktable allows for single or pendulum processing with (2) 48" x 72" (1,219 x 1,828 mm) work zones for processing small to large parts. With average cycle times under two minutes, the contour edgebander consistently produces quality parts, including 360° lap joints.The work piece is supported by means of vacuum cups sitting on a large flat bed. This enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with a 100 m³/Hr vacuum pump. The pump is mounted inside the frame of the machine reducing noise and avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR Revolution 180 operating system is unaffected by panel position.This patented process is controlled by a simple and intuitive interface that doesn't require CNC programming. -- Edge Banding Unit:The VECTOR Revolution 180 uses a cartridge & nozzle glue extrusion system which is ideally suited to this contour banding application.The cartridge glue nozzle is a closed system which only heats the glue as it is used. The glue is not exposed to the atmosphere. This means there is no burning of the glue or dis-coloration & the original color of the glue & its properties are maintained.Another benefit of the glue nozzle system is its close proximity to the first pressure roller. This means that even when slowing for corners, the

VECTOR REVOLUTION - 180, ...CNC Contour Edgebander + Vector Vision UpgradeNumerically controlled automatic Edgebanding Machine precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the X - Y & Z axis.Machine FeaturesBanding unit simultaneously rotates on a high precision C-Axis; AC Brushless Servo motors with: Digital drives and linear guides ensure high speeds & accuracy with a smooth acceleration-and-deceleration. -- NO PROGRAMMING required; extremely simple changing from one tape size to another; Operator only has to make simple adjustments like: Setting the start position, glue height, feeding the new width of tape. and adjusting tape guide height. All else is performed by the machine. -- Cartridge Glue System: Glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod; standard positions are:16 mm (5/8"); 19 mm (3/4"); 25 mm (1.0"); 28 mm (1-1/8"); and 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field:X-Axis 139.7" (3,550 mm); Y axis 72" (1,830 mm); 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Min. external radius & 1.97" (50 mm) min. internal radius, depending on the type of banding materials. 1 mm Minimum banding material thickness & 3 mm maximum banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- Worktable:Phenolic worktable with embedded vernier scales in X & Y axes allow for simple & flexible positioning of 2-stage vacuum pods. Worktable allows for single or pendulum processing with: (2) 48" x 72" (1,219 x 1,828 mm) Work Zones for processing small to large parts. With average cycle times under (2) minutes, the Contour Edgebander consistently produces quality parts, including 360° lap joints.Workpiece is supported by means of: Vacuum cups sitting on a large flatbed; enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum achieved with: 100 cbm/Hr Vacuum Pump. Pump is mounted inside the frame of the machine reducing noise and avoiding airborne dust.Exact workpiece positioning is not critical as the patented VECTOR Revolution 180 Operating System is unaffected by panel position.Patented process is controlled by a simple and intuitive interface that does not require CNC programming. -- Edge Banding Unit:VECTOR Revolution 180 Uses a cartridge & nozzle glue extrusion system, which is ideally suited to this Contour Banding application.Cartridge Glue Nozzle is a closed system, which only heats the glue as it is used. Glue is not exposed to the atmosphere. Result: There is no burning of the glue or discoloration, and the original color of the glue & its properties are maintained.Another benefit of the Glue Nozzle System: Close proximity to the first pressure roller. This means that even when slowing for corners, the glue remains molten until pressed onto the panel by the first pressure

This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

VERVILLE 95-VP-438SE-CCW-35/125 - 4-Station Bagger complete Automatic Bag Placement and Bag SealerComplete line that was used for wood shavings only. The line is in operation at the time of this write-up.The Verville VP438-CCW is a four-station compression bagging system designed for high-efficiency bagging operations. It features high tubes of 125", automatic plastic bag sealing, and the ability to handle bag sizes ranging from 11" x 17" to 30" high. This system is often used in industries like biomass and packaging. It also includes features like an oil tank heater and a modem for remote monitoring.Bagging Capacity: -- It can handle bag sizes ranging from 11" x 17" to 30" high. -- Automatic Features: Includes an automatic plastic bag sealer for seamless operations. -- Height: The system features high tubes of 125 inches, making it suitable for large-scale bagging needs. Additional Features: -- Comes equipped with an oil tank heater and a modem for remote monitoring, ensuring smooth and efficient performance.Included with the system: -- The control box is mounted on the side of the auto-bagger with the Allen-Bradley Panel View 550 unit. --The main 4-section bagger is 125 " tall. --The main master control cabinet, -- The long 45° screw auger to feed from the bottom of the sifter to the top of the bagger, -- The Cousins HP2100 plastic wrapper with a turn table to wrap full skids. -- The master hydraulic tank & pump arrangement with all hoses. -- The full sealed bag auto discharge conveyor belt & turning roller conveyor. --The sifter with the canvas wrap cover. -- The screw conveyor that runs from under the outside dust collection system rotary airlock drops the “good"; wood chips down to the 45° screw with the “light dust going out thru the screw conveyor into an open dump trunk outside.Total HP 75Price Includes Loading on a Truck

VERVILLE VP424-S-CCW BAGGING SYSTEM4-Station Compression Bagging SystemSpecifications & Includes: -- High Tubes of 116" -- Bag Size 11" x17" up to 30" High -- Automatic Plastic Bag Sealer -- Oil Tank Heater and Modem -- Supplied with Transformer for your VoltageLoaded on your Truck