//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i6d SECO SK-20BS 20" Vertical Band Saw Specifications: Actual throat 18-1/4". Table size 22-3/4” LR x 20-1/4" FB, with 45° Tilt. Max. height under guard 12". Blade length 155", Blade width 1". Wheel speed 800 RPM. Equipped with: 3 HP - 3,450 RPM Motor. 20” Rubber-covered cast aluminum wheels. Complete with: Work light.

SELCO WNT 7/730 REAR LOAD, AUTOMATIC PANEL SAW -- Specifications: 177" (4,500 mm) Overall cutting length, 5" (127 mm) max. saw blade projection, 29 HP (22 KW) main & 3.5 HP (2.6 KW) scoring motor. -- Saw Carriage:Variable saw carriage speed from 0 - 606 FPM (0 - 185 MPM), return speed 600 FPM (185 MPM); Rack & pinion drive, driven by AC brushless Servo motors. -- Pusher Fence:Electronically controlled overhead program fence with (8) pneumatic gripper clamps (open up to 5" / 128 mm).Forward speed of 295 FPM (90 MPM) & return speed of 295 FPM (90 MPM); rack & pinion drive, driven by AC brushless Servo motors. -- Operator & Machine Control:PC front end with Selco "OSI" + WINDOWS "7" operating system with easy programming of very complex cutting patterns.15" Flat screen monitor displays REAL-TIME graphics of cutting dimensions & patterns, program cutting list, manual cuts, diagnostic & on-line help.Data input by industrial keyboard & mouse, floppy disk or CD; direct downloading from office PC is possible.OSI (Open Selco Interface) guarantees fully automatic management of cutting patterns by optimizing all machine movements (pressure beam, saw carriage and side aligner pusher positioning, etc.).The numerical control adjusts the optimum saw blade projection for the stack of panels being cut and sets the most appropriate cutting speed, in relation to the stack itself and, when necessary, to the width of trim cut too. -- Rear Load Lift Table:Automatic lift table 173" x 87" (4,400 x 2,200 mm), 12,000 Lbs (5,455 KG) lift capacity.4 HP (2.3 kW) Motor for raise-and-lower, encoder-controlled guide rods for automatic book height adjustment; 28.7" (730 mm) max book height w/o a pit or risers. -- Rear of machine:(3) Lateral aligners to accurately position book of panels on rear table prior to cutting.Rear modular roller support rails with 80 mm dia rollers; rear of machine enclosed for safety. -- Front of machine:Automatic side/crosscut aligning device located inside the pressure beam aligns the panels against the right angle fence prior to cross-cutting, 2.4" - 87" (60 - 2,200 mm) stroke.90" (2,300 mm) Long crosscut fence (front-to-back); (4) Front mounted air flotation tables with rounded fronts 26" x 81" (650 x 2,050 mm). -- Complete with: "Quick Change" saw blade system; "DIGISET" electronic scoring adjustment; Selco "Quick-Opti" optimizing software; CP link. -- Options Include:173" x 87" (4,400 x 2,200 mm), LH facing, rear in-feed/out-feed conveyors with fork cut-outs that allow for staging/loading/unloading from the Rear LH side of the machine. -- Actual Model is SELCO WNT 7/730/4500.

SELCO EB 70 L CNC Front-Load Horizontal Beam CNC Panel SawSpecifications & features: -- 126" (3,200 mm) Overall cutting length, 2.75" cutting height (80 mm saw blade projection), 10 HP main & 3 HP scoring motor. -- Modular roller rear machine table, side aligning device for squaring ripped strips out to 59". -- Variable saw carriage travel speed from 0 - 164 FPM (0 - 50 MPM). -- Electronically controlled overhead program fence, rack & pinion driven, forward speed of 80 FPM, 131 FPM return speed.Equipped with: -- (6) Clamps (open up to 70 mm - 2-3/4"), (3) are closely spaced in crosscut area & (4) are at equal distance in rip cut area; AC Servo motor drives on both saw carriage & pusher fence. -- PC Controller with: Graphics color monitor & "Assist Line"; LED readout integrated into "high tech" look operator control panel (displays cutting dimensions & patterns), (400) cutting patterns with (50) different dimensions for ea. pattern, self-diagnostic. Machine features: -- 1,500 mm (59") Long crosscut fence (front-to-back), (1) side/crosscut aligner. -- (1) Front mounted air flotation table in the crosscut area and (2) front mounted air flotation tables with patented rounded front for moving panel from rip to crosscut position (24" x 59" each). -- 36" Working height; rear of machine partially enclosed for safety.

SELCO EB 120 CNC Frontload Panel SawSpecifications: -- 126" Overall cutting length & 4.7" (120 mm) max. saw blade projection; 18 HP main & 2.4 HP scoring motor, modular roller rear machine table, side aligning device, and (2) longitudinal aligners to accurately position the book of panels on the rear saw table prior to cutting. -- Variable saw carriage travel speed 0 - 328 FPM; electronically controlled overhead program fence, rack & pinion driven, forward speed 196 FPM, return speed 196 FPM.Equipped with: -- (6) Clamps (open up to 122 mm), of which (3) are closely spaced in crosscut area and the other (3) are at equal distance in rip cut area. -- AC Servo motor drives on both, saw carriage and pusher fence. Operator & Machine Control: -- The front end is controlled by a PC, which has a Color monitor integrated into a high-tech-look operator control panel (which displays cutting dimensions and patterns). The panel has virtually unlimited cutting pattern storage capacity, and it is self-diagnostic. Data can be input by keyboard or downloaded directly from the office PC. Complete with: -- 2,300 mm Long crosscut fence stroke (side to side), (2) side/crosscut aligners. -- (3) Front mounted air float tables with rounded front for moving panel from rip to crosscut position, (24" x 79" each). -- Rear of machine partially enclosed for safety.

SELCO EB 90 CNC Front Load Panel SawSpecifications: -- 173" Overall cutting length, 173" pull back; 3.3" (85 mm) max. saw blade projection, 12 HP (9 kW) main saw motor, 2.4 HP (1.8 kW) scoring motor. -- Modular roller rear machine table, side aligning device, and (2) longitudinal aligners to accurately position book of panels on rear saw table prior to cutting. Equipped with: -- Variable saw carriage travel speed from 0 - 197 FPM (0 - 60 MPM), return speed of 197 FPM (60 MPM). -- Electronically controlled overhead program fence, rack & pinion driven, forward speed of 0 - 197 FPM (0 - 60 MPM), return speed of 197 FPM (60 MPM). -- (9) Clamps (open up to 85 mm); AC Servo motor drives on both saw carriage and pusher fence.CNi "NC 400 Plus" control with: Color monitor and "Assist Line" w/LED readout (displays cutting dimensions & patterns, virtually unlimited storage capacity of cutting patterns & different dimensions. "Assist Line" with: Real-time graphics, self-diagnostic, data input by keyboard or possible direct downloading from an office PC. Complete with: -- 90" (2,300 mm) Long crosscut fence (front-to-back), (2) side/crosscut aligners, "Quick Change" saw blade replacement system. -- (4) Front mounted air float tables with rounded front 24" x 79" for moving panel from rip to crosscut position. -- Includes: -- Rear roller module support rails; rear of machine enclosed for safety.

SELCO - HS0-128A, ...Horizontal Auto-Tie Baler -- Motor: 50 HP -- Cylinder: 8" -- Feed Opening: 36" x 28" -- Conveyor NOT included -- Loaded onto your Truck

SELCO - HLO-608-A40, ...Wide Mouth Auto-Tie Horizontal BalerSpecifications: -- Bale size: 48"; x 40"; x 72"; -- Main motor: 40 HP -- Cylinder: 8" -- Twister motor: 2 HP -- Cooler motor: 2 HP -- (4) Tension cylinders: 5" BoreEquipped with: -- Conveyor controls -- Shear bar (tapered & serrated)Available NOW!

SELCO - HLO-608-A40: Wide Mouth Auto-Tie Horizontal BalerSpecifications: -- Bale size: 48"; x 40"; x 72";. -- Main motor: 50 HP. -- Cylinder: 8". -- Twister motor: 2 HP. -- Cooler motor: 2 HP. -- (4) Tension cylinders: 5" Bore.Available NOW!

SELCO HSO-128A50: Horizontal Auto-Tie Baler -- Type: Open end. -- Cylinder: 8". -- Motor: 50 HP. -- Infeed opening: 36" x 28-1/2". -- Bale size: 30" x 40" x Variable. -- Bale weight: Up to 1,200 Lbs (OCC). -- Production capacity: 2 to 4-1/2 TPH. -- Shear blade. -- Hopper size: 36" x 28-1/2". -- Ram face pressure: 103 PSI. -- System pressure: 2,400 PSI. -- Platen force: 120,637 Lbs. -- Cycle time: 11-1/2 Sec (no load).

SELCO - HL-12-LH: Horizontal Baler with Infeed Conveyor• Motor: 20 HP. • Main Cylinder: 6";.• Hopper Opening: 50"; x 28";.• Cycle Time (No Load): 15 Seconds.• System Pressure: 2,000 PSI.• Total Compression Force: 56,556 Lbs.

SELCO - HL50: Horizontal Closed Door BalerSpecifications: -- Large corrugated wide-mouth Baler. -- Horizontal Closed Door. -- Max. amps: Draw 48 amp; max. motor: 39 amp. -- Max HP motor: 30 HP – 60 Hz – 3 phase. -- Bale size: 72″ x 36″ x 48″. -- Feed opening: 50″ x 46″. -- Main pump: 800 PSI. -- Hydraulic pump capacity: 54 GPM. -- Oil reservoir capacity: 180 Gal. -- Cycle time: 20 Sec. -- Ramface pressure: 68 PSI. -- Baling material weight: 1,500 – 1,800 Lbs. -- Bale volume: 72 Cu. ft. -- Main cylinder: 7″ Bore; 62″ stroke. -- Door cylinder: 4″ Bore; 12″ stroke. -- Cylinder needs to be repacked --Reconditioned Guaranteed $59,500

SEVEIN - 12KVA, operates on 50 - 60 Hz, ...Transformer with Neutral wire (on 400 V side). -- General-purpose enclosed, European made, 12 KVA, 3-Phase ventilated Autotransformer. -- Primary 400 V, Secondary 208 - 220 V, 50 - 60 Hz.

SHENG-SHING - SDM-25, ...25" Wide Belt Sander1-Head; 24" width cap.; rubber-covered contact roll; approx. 10 HP motor. -- Abrasive belt size 25" x 48" with: Air tensioning & electronic abrasive belt tracking. -- 5-1/2" Max. height opening with: Manual raise & lower; variable feed speed drive. -- Complete with: Magnetic controls & dust outlet.

SHENG-SHING - SDM-15 ...Wide Belt Sander (Open Ended)15" Single Head Wide Belt Sander with open end for up to 30 " capacity. -- Sanding Head: 15" Wide (30" cap. with 2-pass); 8" Helically Grooved Rubber Covered Contact Roll with 7.5 HP Drive. -- Features: 0" - 6" Part thickness cap., 2-speed conveyor feed 12 or 16 FPM; 16" x 48" Abrasive belts with air tensioning, pneumatic abrasive belt tracking.

--This machine is in an Auction on exfactoryauctions.com-- SHODA MAXXIM 5' x 10' 2-Head CNC Router, with Vacuum Pump – Seller states that machine was run (1) shift from 2002 - 2006, then only a few days per year since! Specifications: Table size 63” x 122” x 29” H, with 3/4” Thick Top. Travels: X-Axis 133", Y-Axis 73", & Z-Axis 10". Max. machining feed speed 590 IPM. Max. positioning speed for X & Y-Axes 1,180 IPM. Equipped with: Moving single-zone vacuum table, with Extra-hard phenolic surface, Front-to-back configuration. (2) 12 kW (16 HP) - 18,000 RPM BT-30 Air-cooled electro-spindle, with Variable spindle speeds 3,000 - 18,000 RPM, AC Inverter, Dynamic spindle braking, Air/Oil mist lubrication. 16-Position Carousel-type automatic tool changer. Features: All Axes with Extra-large precision contour linear guideways. Closed loop AC Servo drives & Precision ground ball screws. Extended extra heavy-duty bridge for full 5' x 10 table coverage. Centralized lubrication system for all spindle & roller bearings, ball screws & guides. Operator Control: FANUC "SERIES 21i-M" Mobile CNC Control, with 10.4" Display, RS-232 Port, PCMCIA Slot, (3) Axes Simultaneous control, Manual pulse generator, Inch & Metric operation, Feed rate & Spindle speed override, Helical interpolation, Full cutter compensation, Background editing features, EIO/ISO recognition. Foot pedal control. Complete with: 2001 TRAVAINI "1-501V1A-460" 40 HP Vacuum Pump, S/N S1433, with Hour meter reading 17,003 Hrs. (10) Toolholders. Dust Manifold. Dimensions without Safety Rails: 202" x 155" x 110" H. Dimensions of Vacuum Pump: 82" x 36" x 65" H.

Only 40 Hrs. Run Time! Shop Fox W1812 Planer Moulder Specifications: 12" Open-sided Mini Planer/Moulder offers smooth moulding and planing. 2 HP Motor belt drives head for 7,000 RPM spindle speed. Very smooth operation with a variable feed rate of 0-18 FPM. Cutterhead Diameter 1-1/4"² Max. material width 6.75"; also planes 7.5" wide. Easily handles material thickness from 1/4" to 7-1/2" max. 9" Min. stock length; max. profile depth 3/4" and max. profile width 6-3/4". Comfortable table working height of 31". Includes: Sturdy work "stand" Front-mounted On/Off controls. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SHOP FOX W1678 Heavy Duty 26" 2-Head Drum SanderSpecifications: -- Heavy Duty 26" 2-Head Drum Sander. -- 24" Wide thick conveyor belt, similar to the ones used with Wide Belt Sanders. -- (2) drums 6" x 27-3/4". -- Enclosed fabricated steel base with easy access doors. -- 5 HP Single-phase motor that drives both sanding drums. -- 1st Head for coarse; 2nd head for fine sanding. -- Independent adjustment on both heads. -- Variable Speed conveyor , 0.25 HP feed drive. -- 0" - 4-1/4" Thickness cap. with manual hand wheel adjustment. -- (2) Each rubber covered infeed & outfeed rollers. -- (2) Dust outlets and push button magnetic controls.

SHRED-PAX - AZ-80, ...Shredder -- Dual Shaft Shredder. -- Motors: (2) 40 HP. -- Blades: 1" Width; (26) blades total. -- Crescent Moon Ram Assist. -- Ram rebuilt. -- Loaded onto your Truck.

SHREDPAX AZ-45 Dual Shaft ShredderSpecifications: -- QTY 2 20 HP Motor -- Voltage 480 V, 60 Cy, 3-Ph. -- Dual Shaft -- Support Stand IncludedLoaded on your truck

SICOTTE - J 3H-7, ...Vertical Boring Machine24" x 84" Table size. Equipped with: -- (5) 1.5 HP Motors mounted on 24" long arms with motor starter and overload relay. -- (5) 1-1/2" Dia. spindles with spring collet 1/2" capacity. -- (2) Spring loaded holddowns.Features: -- 0" - 8" Vertical table feed, hydraulically operated; variable feed and table travel adjustable from front of machine. -- 3 HP Hydraulic pump motor with reservoir. Complete with: -- Electrical Control System with separate motor controls. -- Single or continuous stroke. -- Manual and automatic cycle. -- Foot pedal actuation. -- (1) Safety guard.