EXTREMA DB-50.3 TYPHOON BLOWER. Capacity 5 HP, 3,200 CFM. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller, 10" inlet, 13" impeller, 12" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. - Complete with magnetic starter. -- Note: 460 Volt available

EXTREMA DC-4100 Baghouse Dust CollectorThe "DC-4100" baghouse dust collector is designed to achieve maximum airflow with a superior filtration area. This is achieved by using (36) smaller diameter filter bags to have more filter media in the same space as other similar dust collectors of its size. More filter area means better airflow with less filter maintenance. A manual bag shaker is included.The DC-4100 meets the NFPA664 CFM requirements for indoor dust collectors. The compact design allows this maximum filtration unit to use a depth of less than three and one half along a wall. The 10HP main motor has a dynamic balanced impellor and a magnetic starter is included.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 361 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (36) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 12".

EXTREMA - DCY-1220 L3 TYPHOON: Cyclone Filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system before passing finer particles through the fan and filter. -- Air volume rated @ 8,800 CFM. -- Unit includes: 20 HP Motor with a Soft Start already wired in. -- Rotary air lock with: 1 HP Motor @ 38 CFM. -- Low noise operation. -- Standard support frame: LEG 3; 164" clear height x 149" clear width x 91" clear depth. Includes after filter Baghouse DC-327E. Features: 16" Inlet; (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) micron filter. -- Unit is enclosed.

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 Volt / 3 Phase.

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA XS-1E52 SINGLE HEAD WIDE BELT SANDER51" Working width, up to 6" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 30 HP main motor; -- 52" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower the table via (4) jack screws, the over-thickness bar at the front of the machine, and the AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air-operated disc brakes on the main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for 460V operation.

EXTREMA 126TV Single Sided Planer;26" Max. width capacity, 11.75" thickness, Solid cast iron construction. -- Precision ground cast iron table with motorized programmable height adjustment; 1/2 HP elevation motor. -- 20 HP Main drive motor -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- 1 HP Feed drive, variable feed speed setting from 20 to 75 FPM. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers; (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch and Emergency stop. -- Includes Operations manual, parts list & tool kit.

EXTREMA XP-124TV Single Head PlanerSpecifications: -- Solid cast iron construction. -- 15 HP Main drive motor, 1 HP feed motor 20 to 70 FPM, 1/2 HP elevation motor. -- Precision ground cast iron table w/motorized programmable adjustment. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" insert cutterhead with (4) sided inserts. -- Fixed feed speed setting for consistent stock removal. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers.Features: -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor. -- Magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit. -- Options: Single-phase power, please add ...$ 100, 460 volt add...$ 150.

EXTREMA XP-610 SINGLE SIDED PLANER24" Width capacity, 8-3/4" thickness, solid cast iron construction. -- 10 HP main drive motor -- Precision ground cast iron table w/motorized height adjustment, with digital thickness display; 1/2 HP elevation motor. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- Variable feed speed from 20 to 42 FPM; 1 HP feed drive. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit.

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EXTREMA XP-126A PLANER WITH HELICAL HEAD26" x 11-3/4" Cap., 5/16" max. material removal, 10-1/2" min. part length; 20 HP WESTINGHOUSE / TIKO belt driven motor, STEALTH helical carbide insert cutterhead - 6,000 RPM, variable speed feed 20 - 75 FPM. -- Equipped with: Powered raise-and-lower of 27" x 35-1/2" table, digital thickness controller, sectional chipbreakers, sectional infeed roller & dual outfeed rollers, and (2) adjustable bed rollers.

Extrema WS-110 Single Spindle Shaper -- 3/4" & 1" Interchangeable spindles. -- 3 HP Single Phase, 3,450 RPM motor designed for operation in most smaller shops -- Belt drive for spindle speeds of 8,000 & 10,000 RPM _ 2-5/8" capacity under the nut (3/4" spindle) and 3-7/8" vertical spindle travel will accommodate a variety of cutters. -- Large Table size 28" x 30" with a 6" max. dia. table opening -- Includes Fence assembly, miter gauge, 1/2" collet adapter, and power feeder.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

HOLZ-HER CONTRIGA 1366 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: NC Controlled Edgebander has the ability to program all functions including: Panel thickness, edge feed, glue application, end trimming, radius/fine trimming, corner rounding, scraping, and buffing. - Virtually eliminates setup time by selecting & loading program that automatically activates these functions simultaneously.Coil edgebanding up to 3 mm PVC cap.; 2-3/8" max. panel thickness; 7" min. panel length; powered pressure beam opening adjustments. Equipped with:"1961" Premilling Station: PC Controlled with up to 45 mm (1-3/4") milling height; (2) motors @ 2 kW (2.6 HP) - 9,000 RPM each. -- Features: Granulate glue system with: Hopper System with "floating" applicator nozzle & "quick melt" feature. -- Automatic magazine for coil, strip & solid edgebanding model "1901" with: TRACTOR-BELT Feed System, Heavy-Duty guillotine for 3 mm PVC. -- "1914" Pressure Section for 12 mm thick edgebanding with: (3) Rollers, each w/individual pressure control, powered 1st roller with electronic speed control synchronized with chain feed speed; Servo motor adjustment for edgebanding thickness from PLC. Workstations:"1819-1" Double motor (1 HP - 6,000 RPM motor ea.) end trim units with: "Uni-Point" Swivel system; "quick change" from flush to 0° - 15° bevel from operator panel. -- "1962" Top & Bottom flush trim unit: 2.6 HP - 200 Cy HF motors; 12,000 RPM cutter speed; NC Servo control, non-tilt. -- "1966" Top & Bottom fine trim unit with: Motorized 5-axis positioning; 1.5 HP - 200 Cy HF motors;, 12,000 RPM cutterhead speed; bevels 0° - 45°, Servo control; all adjustments programmable through the PLC. -- "1933 & 1934" 4-Motor corner rounding unit for top & bottom of leading & trailing corner when edgebanding all (4) sides; 0.7 HP - 200 Cy ea.; both motors with Servo positioning from control panel; Servo adjustment of entire unit (base). -- "1927" Scraper Unit: Finishing up to 5 mm thick PVC banding for radius range from 2 - 5 mm; vertical & horizontal tracing wheels, Servo positioning enabled through "PC"; Servo controlled in/out of base. -- "1964" Top & Bottom Glue scraper. -- "1851" Oscillating buffing unit: Cleaning & polishing of panel; (2) 0.25 HP - 1,440 RPM motors; tilts 0° - 45° vertically and 0° - 20° swivel on horizontal plane.Other Specifications & Features:Variable feed speeds up to 25 MPM (81 FPM); panel overhang beyond chain 35 mm (1.38"); features automatic track pad lubrication. Operator Interface:PPC-231 Controller for line control, glue temperature & flow, feed speed setting, and motorized holddown pressure beam adjustment. -- Frequency inverter, outboard panel support, and sound enclosure w/interior lights over all milling units. -- Actual Mode is HOLZ-HER CONTRIGA 1366

HOLZ-HER ACCURA 1556 4.0 PREMIUM EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + GluJet EVA / PUR Gluing Systems:Specifications: -- Working Capacity: Edge thickness min./max. 0.4 - 3 mm (0.02 - 0.12") for coiled material, 15 mm (0.59") 1/2"+ max for strips.Panel thickness 8 - 60 mm (0.315" - 2.36"); workpiece width min. 60 mm (2.36"); workpiece length min. 140 mm (5.5"); Feed speed 10 - 20 MPM (33 - 66 FPM).Machine In-Feed Configuration: -- Pre-Milling Station "1802": 2 x 1.2 KW (1.6 HP) - 12,000 RPM motors; Diamond cutter-heads with ProLock quick clamping system. Quick-Lock adjustable in-feed fence with digital indicator. -- Edge Magazine "1901": for coil and strip processing, utilizing motion detector to ensure accurate, trouble-free positioning of edge material; exclusive "Tractor-Belt feed System", edge guide equipped with automatic guillotine lock-out for safety, 3° approach angle allows easy feeding of solid wood edges. -- Pressure Section "DW 701": with (1) large driven (synchronized with feed-speed) roller and (2) cantered idle rollers, adjustable by hand wheel and scale. -- GLUING SYSTEM "GJ 301" (Glue Jet)... Processes "EVA" or "PUR" Glue in Cartridge or Granulate Form, granulate requires an "optional" hopper. Upper glue line height positioning is set automatically with hold-down beam setting. Heat-up time to ready stage takes only 2 - 3 minutes!Additionally equipped with "iTRONIC" Adaptive pressure and glue quantity control for intelligent automation. Adaptive trimming blade. Automatic glue quantity control. Adaptive pressure unit control. Automatic cleaning routine. Remaining glue quantity indicator.Workstations: -- End Trimming Unit "KA 702": Front & rear 2 x 0.45 KW (0.6 HP) - 9,000 RPM motor each, uni-point swivel-axis for no re-indexing when changing from flush to bevel end trim (0° - 10° bevel),"PCS" programmable pneumatic change-over from flush to bevel. -- Flush Trimming Unit: Top & bottom Flush 15 mm unit; 2 x 0.65 KW (0.88 HP) - 12,000 RPM, each motor. -- Fine/Bevel/Radius Combination Trimming Unit "FR 701": Radius 2 mm trimming, servo controlled, 2 @ servo motors (1) for horizontal copy wheel & (1) for tool spindle position) programmable top & bottom unit 2 x 0.65 KW (0.88 HP) - 12,000 RPM each motor.Uni-Point design with no second adjustment, pneumatic, programmable tilt action for changing the degree of bevel, digital counters for vertical copy wheel position and pneumatic air cylinder for in/out pre-positioning of trimming motor. -- Corner Rounding Unit "FF 701": (4) Motors 0.22 KW (0.30 HP) - 9000 RPM for up to 3 mm edge thickness and work-piece thickness min./max. 12 - 60 mm (0.473 - 2.362"), max. feed speed 10 MPM (33 FMP). -- Profile Scraping Unit "ZK 501": Top/Bottom, servo motor controlled/programmable knife position, vertical copy wheel adjustment with quick setting spindle.For PVC edges, reversible insert carbide knives, equipped with air-jet blowers and chip collector box. -- Glue Scraping Unit " FK": Flat surface,

HOLZ-HER - 1619, ...Boring Machine (Construction & Line Boring) -- Specifications:(19) Spindles on 32 mm centers; bores vertically from top and horizontally from the rear; repositions via manual air shock assisted tilting.2 HP Motor with: 2,800 RPM Gear driven boring head. -- Features:4-Position turret style depth stop for boring depth and a 4-3/4" max. stroke of boring head.24-3/4" Working width; 27-1/8" max. panel width; 19-1/2"; x 38"; x 32-1/2"; H table size. -- Equipped & Complete with:RH & LH Indexing fence with flip stops; (2) indexing pins (for continuous line boring); (3) 4" dia. pneumatic holddown clamps; foot pedal actuator; magnetic push button starter. -- Actual Model is: HOLZ-HER 1619Dimensions of this specific machine with pallet: 52" x 40" x 65" H.Dimensions of this specific machine when vertical: 52" x 37" x 60" H.Dimensions of this specific machine when horizontal: 52" x 51" x 46" H.

HOLZ-HER PRO-MASTER 7122 K 4X CNC MACHINING CENTER (W/ATC/BORING/"C" AXIS): -- Specifications: Working capacity: "X" Axis 142" (3,607 mm); "Y" axis is 59" (1,500 mm); "Z" axis stroke is 22.2" (565 mm); max. material thickness: 8.26" (210 mm) from the top of the vacuum pod. -- Positioning Speed: "X" Axis is 393 FPM (120 MPM); "Y" axis is 328 FPM (100 MPM), "Z" axis 82 FPM (25 MPM)."X" Axis travel on high precision prismatic STAR guides & ground helical rack; "Y" & "Z" axes travel via hardened ground ball screw. -- Worktable:(6) Support rails, (2) adjustable vacuum pods per rail.Laser positioning system for quick positioning of pods and with value input from Controller according to part size and machining required.(6) Pneumatic pin stops located in the rear of the machine; (6) pneumatic pin stops located in the front of the machine.(2) Side stops & (2) central stops for mirror imaging; (2) independent working areas.Stops can be fitted with "quick fit" mushroom clamps for clamping of small or awkward shaped parts. -- Boring Head:4 HP (3 kW) Motor; variable spindle speed from 1,000 - 6,800 RPM; (18) independent vertical boring spindles with: (12) Spindles in "X" axis & (6) spindles in "Y" axis.(6) Horizontal spindles with: (2+2) in "X" Axis & (1+1) in the "Y" axis.(1) "X" Axis grooving saw for max 120 mm dia. blade. The boring head is arranged to accommodate (2) operating units. -- Machining Units:(1) 13 HP (9.7 kW) Vertically mounted liquid cooled electro-spindle with: HSK 63F Adaptor; inverter driven 1,000 - 24,000 RPM with max. torque from 12,000 - 24,000 RPM.(1) NC Controlled "C" axis for 360° horizontal processing.(1) 18-Position ride-along rotary tool changer plate for "on the fly" ATC.Max. tool dia. 85 mm (if fully loaded) or 200 mm (with free spaces). -- Operator & Machine Control: SIEMENS PC Front-End + "CAMPUS" + Windows "7" operating system with 3D simulation.15" Color monitor; standard PC Keyboard & mouse; CD-ROM drive. - Card ports: (1) AGP, (1) PCI, and (1) ISA; (2) serial ports & (2) parallel ports; (2) PS/2 ports & (4) USB ports; (2) PCI Bus-Master IDE ports; (3) Com 905B-Combo fast Ethernet cards.Hand-held pendant for remote control start/stop of working cycle, speed control, reset function, etc."CAMPUS" is user-friendly CNC software with office and machine license; extensive 3D simulation module as standard feature; integrated CAD module and versatile macros for easy programming. -- Complete with:(1) 100 cbm/Hr Vacuum Pump; tool length "Touch-Off" Probe; emergency stop rope & pressure sensitive safety mats that will instantly place machine in "pause cycle" when stepped on.Sound absorbing protective head enclosure with debris curtain around bottom edge. -- Actual Model is: HOLZ-HER - PRO-MASTER 7122 K 4X.

HOLZ-HER 1516 CASE CLAMP (SINGLE-BAY: -- Specifications:1-Bay Clamp, 100" x 50" x 24" clamping cap.; (1) movable, vertically positioned clamping beam with (3) horizontal clamps, (4) adjustable vertical clamps. -- Total of (14) pressure cylinders with 3-7/8" stroke & (4) adjustable counter-pressure bars; 700 Lbs/cylinder pressure at 100 PSI compressed air; built-in controls with pressure gauge.