CANTEK MODEL CFS100 / EM-12 DEFECT SAW AND END-MATCHING SYSTEM:Consisting of a CANTEK model "CFS-100" Optimizing Cut-Off Saw followed by a CANTEK Model "EM 12" Through-Feed End Matcher and with the following specifications and features: CANTEK "CFS-100" OPTIMIZING CUT-OFF SAW -- Up to 20 mm X 200 mm or 100 mm X 100 mm( 3/4" X 7.87" or 3.9" X 3.9" cutting capacity with 18" x 30 mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP servo drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed. -- Machine is ideal for separating crayon marked waste zones from useable material before entering into a feed-thru End Matcher; provides (3) times greater production than manual cut-off saws.5% + Material recovery (yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm / 0.40"; control employs a touch screen for easy learning and operation.Features: -- New machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included.(5) Cutting modes include: -- Adjustable end cuts to a max. of 10mm (0.4") -- Fixed length of cutting mode. -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only). -- Cutting on fluorescent marks with double-end trimming (perfect solution for end matching). -- Reading fluorescent marks with double end trim, fixed-length, random length end match, and finger joint block cutting. CANTEK "EM-12" END MATCHER -- Continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity; -- 295 FPM max. feed speed; average speed of 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; -- 5.5 HP Shaper motors, 1 HP feed motor an

CANTEK EM-12 End Matcher;1.6" to 12" Width x 0.4" to 1.38" thickness (to 2-1/4" optional) x 10.6" min. length capacity. Unlimited lengths possible.Specifications: -- Feed speeds to 295 FPM with approximate production speeds of 77 FPM (based on 6-1/2' incoming boards). -- Standard 173" long infeed table and standard 86" (2,200 mm) long outfeed table; -- (2) 10 HP cutterhead motors with 40 mm spindle diameters; 1 HP feed motor; 1/2 HP motor drive to cutterhead carriage; clamping pressure from top and side; 24 volt DC controls.Standard equipment and Features: -- Designed for machining tongue & groove with or without V's on flooring and panel products; designed to be used for finger joint cutting. -- Heavy-duty self supporting main frame; compact design requires minimum floor space.Feedworks: -- Capable of processing material as short as 11" to an unlimited length; variable speed through-feed systems is controlled by frequency inverter; through-feed system allows the tongue to be cut simultaneously on the tail of one board and the leading edge of the next board. -- Powered top Urethane rolls and spring loaded bed rollers feed the material into position for processing. -- Pneumatic side pressure ensures the material is held square against the fence.Complete with: -- Safety and noise reduction enclosure; convenient touch screen control is used to quickly activate and adjust the machine functions. -- Powered 176" long infeed conveyor is included (additional length optional); with a 86.6" long outfeed table (additional length optional). -- Includes: (2) Individual Precision Insert Tooling Heads as Supplied with Machine & stacked to make (1) pair of heads; set of heads provided for groove on left and tongue on right.

COSTA - KK CC-CCC 1350, ...5-Head Top & Bottom Wide Belt Sander.53" Width capacity; (2) Bottom drums, (3) Top drums.Bottom Machine: -- Constant pass line height: 1,000 mm (39"). -- Motorized infeed conveyor. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder ,16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW. -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table: 10 HP (7.5 kW) motor. -- Vacuum set pneumatic for (2) levels of vacuum pull control.Top Machine: -- Infeed roller. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder, 16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table - 10 HP (7.5 kW). -- Vacuum set pneumatic for (2) levels of vacuum pull control..Equipped with and Features: -- All drives are equipped with disc brakes. -- Each Sander with vacuum feed belt with fans..

COSTA - KBH CCCT 1350 & KH2 CCCT 1350, ...Top & Bottom Sander Line.Head Configuration:Machine #1 - "KBH CCCT" 4-Head Bottom Sander. Bottom Head #1: ~10" Dia. grooved Steel Drum, 47 HP motor. Bottom Head #2: ~10" Dia. grooved rubber covered contact drum, 47 HP motor. Bottom Head #3: ~10" Dia. grooved rubber covered contact drum, 32 HP motor. Bottom Head #4: Finishing platen, 23 HP motor.Machine #2 - "KH2 CCCT 1350" 4r-Head Top Wide Belt Sander. Top Head #1: ~10" Diameter Grooved Steel Drum, 47 HP - 460 V motor. Top Head #2: ~10" Grooved rubber covered contact drum, 47 HP motor. Top Head #3: ~10" Grooved rubber covered contact drum, 32 HP motor. Top Head #4: Finishing platen, 23 HP motor.Specifications: -- PC User interface for each machine. -- Sanding belt size: 53" x 103". -- 96" Belt conveyor in between machines. -- 20 HP Vacuum Blower for each machine's vacuum bed.

COSTA BL 1350 1,350 mm (53.15") 4-Head Denibbing Sander, with (2) Cross Brush Belts & (2) Brush RollsSpecifications: -- Thickness cap. 1/8" - 6-1/4". -- Cross brush speeds belt 3 - 26 FPS. -- Brush roll speeds 130 - 1,300 FPM. -- Feed speeds 16 - 82 FPM.Equipped with: -- 1st & 2nd Heads: Each with 2"; W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. -- (3) 2"; Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. -- 3rd & 4th Heads: Each with 62"; L x 16"; Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. -- 2-5/8"; dia x 7/8"; w swivel rubber wheels before each brush roll head. -- (1) 2"; Dia. Rubberized hold-down roll after last brush roll head. -- 53-1/2"; W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2"; W & 2"; L Centers, 2-1/2"; Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. -- Control motor load meters.Complete with: -- Instruction Manual.

--This machine is in Auction @ https://exfactoryauctions.com/Detail/FD-230117/event/A122024$1. --Low starting bid! Equipped with: 1st & 2nd Heads: Each with 2” W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. (3) 2” Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. 3rd & 4th Heads: Each with 62” L x 16” Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. 2-5/8” dia x 7/8” w swivel rubber wheels before each brush roll head. (1) 2” Dia. Rubberized hold-down roll after last brush roll head. 53-1/2” W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2” W & 2” L Centers, 2-1/2” Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. Control motor load meters. Complete with: Instruction Manual.

COSTA LEVIGATRICI WD7-CCCC-600 Steel Plate & Part GrinderSpecifications: -- Max. finishing width 23.64" -- Max. thickness of mild steel 6.3" -- Number of grinding heads (4) -- Motors (1 & 2) 30 HP -- Motors (2 and 3) 20 HP -- Machine weight 14,700 LbsEquipped with: -- Schneider Magelis control with display -- (4) Load meters -- Variable speed heavy duty pass-through conveyor & exit metal roller conveyor -- Coolant system with paper filtration -- Manuals

COSTA - K7 CCCT 650: 4-Head Wide Belt Sander; working width: 650 mm (25.6"); constant pass line conveyor height.Excellent Veneer & Solid Wood Sander with: (3) Contact Rollers and (1) platen.Head Configuration -- 1st Head: Steel contact roller; 250 mm (9-7/8") diameter; driven by 37 kW (50 HP) motor. - Abrasive belt speed 24 MPS (78 FPS). -- 2nd Head: Rubber-covered contact roller; 250 mm (9-7/8") diameter; Shore hardness 70; driven by 30 kW (40 HP) motor. - Abrasive belt speed 18 MPS (59 FPS). -- 3rd Head: Rubber-covered contact roller; 250 mm (9-7/8") diameter; Shore hardness 70; driven by 22 kW (30 HP) motor. - Abrasive belt speed 18 MPS (59 FPS). -- 3rd Head: Segmented finishing platen, electronically controlled narrow segments conform to panel width & length for thin veneer sanding; driven by 11 kW (15 HP) motor. - Abrasive belt speed: Infinitely variable 3 - 16 MPS (30 - 52 FPS). -- Sanding Belt Info: Abrasive belt; air blast abrasive belt cleaning; pneumatic belt tensioning with: Electronic tracking on all heads. - Grit set system for abrasive belt grit compensation. -- At Outfeed: Brush Roller 180 mm (7"); driven by 1.1 kW (1.5 HP) motor. Equipped with: -- PLC Processor controls with touchscreen; integrated control cabinet. -- Feed System & Conveyor Bed Min./max. working height: 3 - 160 mm (1/8" - 6-5/16"). Variable feed speed conveyor with: Inverter control 4 - 20 MPM (13 - 65 FPM). Constant Pass Line at: 920 mm From floor (36"). Vacuum conveyor bed assembly. Infeed & outfeed spring loaded holddown shoes on all heads. Powered raise & lower of conveyor bed with LED readout.Also included: About ...$15,000 of sanding belt.

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CD600 - CP Manfacturing: Can Densifier -- Successful recycling is efficient recycling. There is simply no more efficient way to handle aluminum cans than to densify them.The "CD600" separates and densifies 500 - 1,000 Lbs of aluminum cans per hour into 18 Lbs biscuits. These uniformly sized biscuits stack & band easily without pallets into 2,500 Lbs bundles for easy handling.Densifying allows you to ship max. weight loads - meaning you will never pay to ship air again. The CD600 is unusually quiet and remarkably compact. It is entirely automatic, eliminating the need for constant attendance while automatically adjusting to accept whole or flattened cans.Features Processes from 500 to 1,000 Lbs/Hr aluminum cans. Automatically adjusts for whole or mixed cans to give the max. Lbs/Hr hour throughput. Fully automatic cycle eliminates the need for constant attendance. All machine functions are operated by solid-state, programmable controllers. Ideal densifier for indoor use due to: Low noise level; compact size; attractive design. Min. number of moving parts: Fully enclosed for max. operational safety. Removable bale chamber liners. Rugged construction & innovative design. Biscuit eject guard.

CP MANUFACTURING - CP250: Can Flattener -- 230 V - 3-Phase. -- (1) Blower Tube included. -- Infeed Conveyor. -- Magnetic Separator. -- Up To 2000 Lbs of whole cans.

SCM - ACTION PT 2500: 8' Automatic Case ClampSpecifications -- Max. standard working dimensions: 2,500 mm L x 800 mm W x 1,250 mm H (98.43" L x 31.50" W x 49.21" H). Min. standard working dimensions: 200 mm L x 150 mm W x 200 mm H (7.87" L x 5.91" W x 7.87" H).Working height: 600 mm (23.62"). -- Vertical pressing force: 15 kN (3,372 Lbs). -- Production cap. 400 cases/shift.Equipped with: -- (6) 39-3/8"; L x 1-5/8"; H Horizontal pressure devices; (3) on each side, (1) Fixed top pressure device to top platen, (1) Middle suspended adjustable pressure device for processing base cabinets upright, bar stays consistent with drawer rail position, & (1) Bottom adjustable pressure device. -- Rack & Pinion System with: Brushless motors. -- Front & Rear: Safety light curtains. -- SCHNEIDER ELECTRIC - "MAGELIS": 5-1/2" Color touchscreen control.Complete with: -- Technical Documentation. -- 480 V DELTA/208Y/120 V Step-Down Transformer.Transformer Dimensions: 21" x 15" x 30" H.

CRAM-A-LOT - HX-60: Closed Door Baler with Cart Dumper & Infeed ConveyorSpecifications: --The CRAM-A-LOT "HX-60 HH" & "HX" Series Balers are ideal for warehouses and designed for ease of installation, operation, and maintenance. -- CRAM-A-LOT® HH & HX Series Balers are: Built with extra Heavy-Duty construction; ideal for warehouses & recyclers who deal with large quantities of corrugated and paper products.Baler is designed for long hours of operation and can operate either manually or automatically with photocell control. Optional custom-engineered Feed Conveyors and Cart Dumper Systems efficiently control Baler feed rates for optimum performance in a complete Baling System.Standard Features include:ANSI Z245.5 Compliant: All Compactors meet or exceed ANSI Z245.5 safety standards.UL/CUL Listed Control Panels.UHMW Ram Shoes: Adjustable to assure straight tracking and readily replaceable, should the need arise.Oil Sight Gauge: Oil level at a glance.Oil Filter: Replaceable "spin-on" cartridge to keep your oil clean.Heavy-Duty Controls: NEMA 4-Rated pushbutton controls with "key lockable" start switch.Automatic single-cycle operation. -- Bale Size: 60" x 30" x 40". -- Bale Weight: Up to (OCC) 1,400 Lbs. --Throughput: (OCC) 2-1/2 Bales /Hr. -- Cylinder: 7".

CRAM-A-LOT - SCR-T2-34: 34-Yard Self-Contained CompactorsSpecifications -- Cylinder: (2) 4". -- Main motor: 10 HP. -- Feed opening: 41″ x 58″ (1,041 mm x 1,473 mm). -- Capacity: 34-Yard. -- Ram force: Up to 24 tons.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

CRESSWOOD HF-36-30 Wood Grinder --Motor HP 30 --Cutting Chamber 36″ x 45″ --Ram Stroke 30″ --Rotor Diameter 10″ --Grinding Head Speed 50-150 rpm --Frame Thickness 3/4″ --Number of Cutter Teeth 42 --Shaft Diameter 4″ --Mid-Range Hopper Volume 2.5 Cubic Yards --Floor Area of Unit 71″ x 195″ -- Includes Control PanelShipping Weight 5,700 lbs. Specifications are subject to change The output of these machines can be optimized for your application by selecting different screens, amount of cutter teeth, cutter teeth placement, and rotor selection";

CRESSWOOD EF-30LR HORIZONTAL WOOD GRINDERThe Cresswood EF-30LR Shredder is built to take on your toughest wood waste challenges. Designed for high-volume shredding of pallets, crates, rippings, cut-offs, blocks, and particle board, this horizontal end-feed grinder ensures consistent material flow and maximum throughput. Its durable construction and smart engineering make it ideal for heavy-duty use in lumber yards, manufacturing, and woodworking facilities. With an intuitive design and powerful components, it's built for long-term productivity.Key Features & BenefitsOptimized Material Flow with Variable Speed Feed Roll• Get consistent feed performance, no matter the material size or density• Automatically adjusts feed speed to prevent jams or overloads• Handles a variety of wood waste types with easeRugged Construction for Long-Term Durability• Built tough to withstand years of industrial use• Heavy-duty steel frame resists vibration and wear• Spherical roller bearings increase strength and longevityAdvanced Cutting Technology for Maximum Output• Delivers consistent particle size and clean, efficient cuts• Equipped with a high-efficiency Destroyer Cutterhead• Replaceable anvil supports extend component lifespanSmart Operation & Maintenance Features• Designed for easy servicing and user-friendly controls• Easy access panels simplify maintenance and part replacement• Standard 12′ vibrating conveyor ensures reliable outfeed

CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.