Cantek E6 Oscillating Edge Brush SanderIdeal for sanding the edges of cabinet doors, stair treads, or furniture components.Brush abrasive can sand into profiles or break the edges.Oscillation ensures optimum usage of the abrasive and ensures a quality sanding result. -- Adjustable spindle height for maximum usage of the abrasive. -- Adjustable & removable back fence for linear or curved sanding --Variable speed sanding head. -- Magnetic starter with emergency stop button. -- Built in dust hood -- Comes with 1 (one) set of 150 grit abrasives

CONCEPTION CRP-180 Short Block Feeder Infeed ConveyorSpecifications: -- About 4 m long X 1.2 m wide, 2-ply rubber belt, friction back with Photocell for automatic operation -- Short Block Feeder; Blocks to be 25mm longer than width -- 14' rotating carousel with adjustable speed via VFD with Motorized wheel to avoid blockage -- Exit opening adjustable to the block width -- 200 mm x 7m long belt conveyor to carry the blocks to index rolls; Servo indexer controlling the flow powered by an electric motor; Speed-up belt powered by an electric motor -- Wane System: Scanner to detect wane integrated in conveyor -- Display screen to show wane detected; Kicker to kick blocks that are not in good orientation -- Conveyor to return it into the spreader belt conveyor -- Automatic Operations

CONQUEST 1-23H CONSTRUCTION / LINE BORERUSA-Made 46-spindle Horizontal/Vertical Boring Machine.Specifications: -- (2) 2 HP BALDOR Motor to drive a helical gear head with spindles on 32 mm centers. One head with (23) Spindles in the vertical plane and One head with (23) spindles in the horizontal plane. -- Pneumatic head movement to reduce operator fatigue. -- 20-1/2" x 36" Cast iron front table.Complete with: -- 98" Back fence with repeat stops. -- (2) Pneumatically operated index pins & (2) pneumatically operated holddowns. -- Collets that accept 10 mm shank bits. -- Bit requirements of 10 mm shank. -- Foot pedal control....$150.00 crate charge.

CONQUEST 1-23H Horizontal 32 mm Boring Machine;Specifications: (1) 23-Spindle horizontal boring head, 2 HP "BALDOR" motor, helical gear driven spindles spaced on 32 mm centers, 3,450 RPM; cast table. -- Equipped with: Pneumatic head activation, side fences. -- Complete with: (2) Pneumatically activated holddowns and foot pedal. NOTE: This unit has 2 sets of arms. All the screws have been replaced for the drill bits. Ready to go to work!

CORDES STAIR-ROUTER MODEL "40" Automatic CNC Stair Stringer Router CORDES STAIR-ROUT "40" Fully Automatic 3-1/2 Axis CNC Stair Stringer Router for trenching box stairs, centers, 45° cut but not open stairs.. Unit automatically cuts rise, run, and advances to the next board. This model was developed over (4) Generations of improvements. Basic Operation: -- Operator inputs the parameters for rise, run and number of cuts & press start on the user friendly display, in decimal or fractions & no programming is needed. -- After cutting, an operator makes a choice of repeating with the same parameters (default) or entering changes to one or more parameters. Specifications -- Double or Single Stringer 6" - 14" by 5/4" to 2-1/2"; For clean cuts (2) high speed 5.5 HP high frequency motors with solid state variable speed drives; 1/2" dia. capacity tool shank. -- CNC control: Minimal operator training needed; Operator can choose to repeat a cycle or change parameters and automatic rise, run, cutting and board advance; Standard Box Step Route with Round Nose; Screen displays a diagram of step; heavy duty steel construction.Machine Selections can be divided into (3) groups: -- a.) Basic Operator: Includes Rise, Run, No. of Rise, Type of Rout, Thread Thickness, Nose Length, Stringer Width, Tool Dia., Tread Clean-out; -- b.) Advanced Operator: Nose Width, Nose to Fence, Pocket Length, Riser Thickness, Rise Wedge Angle, Run Wedge Angle, Tread Clearance, Riser Clearance, Top Riser; -- c.) Supervisor, in which a password is needed: Feeds, Speeds, Precision Adjustments, Component Operations, Password Changes, Statistics. Dimensions/Electrics: -- Footprint w/o overhang is 54" x 61", height 68" & weight is 3,500 Lbs; -- Electric load is 30A @ 208 - 220 V, 3 PH and 15A @ 115 V, 1 PH for control power; 80 PSI of clean dry compressed air.Features: -- The main actuators have both been rebuilt in the last couple of years by the manufacturer, CORDES". About $5k each.. Was running on 220 V single phase.

COSMEC NR32-16CUK 510 CNC Router with ATC and Boring:63" x 122" Fixed table: Moving gantry design in a front-to-back configuration; 2-zone Phenolic vacuum table with pop-up pins for part location. -- Equipped with:(1) 10 HP "HSD" ISO 30 Type ATC spindle, 8-position side-mount tool carousel, variable spindle speed from 800 - 18,000 RPM, 11" Z-axis stroke. -- Boring unit:(1) 17-Spindle boring block (11) vertical and (6) horizontal and X-Axis - 5,000 RPM. -- Axis travel: X-Axis travel 3,190 mm (125.6"), Y-Axis travel 2,010 mm (79.1"), Z-Axis travel 280 mm (11.0"); Z-Axis clearance under rail 250 mm (9.84") - Rapid traverse on X- & Y-axis 38 m/Min (1,496 IPM). -- Control:OSAI series 10 numerical control with screen and including, 3-axis linear & circular interpolation, and RS 232 connection with a user-friendly operator interface. -- All axes Incorporate brushless, closed-loop Servo motors driving precision ball screws and ride on STAR linear guideways with an automatic lubrication system servicing the way and ball screw bearings. -- Complete with:Vacuum pump, assorted tool holders, and manuals.

--This machine is in Auction @ https://exfactoryauctions.com/Detail/FD-230117/event/A122024$1. --Low starting bid! Equipped with: 1st & 2nd Heads: Each with 2” W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. (3) 2” Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. 3rd & 4th Heads: Each with 62” L x 16” Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. 2-5/8” dia x 7/8” w swivel rubber wheels before each brush roll head. (1) 2” Dia. Rubberized hold-down roll after last brush roll head. 53-1/2” W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2” W & 2” L Centers, 2-1/2” Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. Control motor load meters. Complete with: Instruction Manual.

COSTA - KK CC-CCC 1350, ...5-Head Top & Bottom Wide Belt Sander.53" Width capacity; (2) Bottom drums, (3) Top drums.Bottom Machine: -- Constant pass line height: 1,000 mm (39"). -- Motorized infeed conveyor. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder ,16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW. -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table: 10 HP (7.5 kW) motor. -- Vacuum set pneumatic for (2) levels of vacuum pull control.Top Machine: -- Infeed roller. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder, 16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table - 10 HP (7.5 kW). -- Vacuum set pneumatic for (2) levels of vacuum pull control..Equipped with and Features: -- All drives are equipped with disc brakes. -- Each Sander with vacuum feed belt with fans..

COSTA - KBH CCCT 1350 & KH2 CCCT 1350, ...Top & Bottom Sander Line.Head Configuration:Machine #1 - "KBH CCCT" 4-Head Bottom Sander. Bottom Head #1: ~10" Dia. grooved Steel Drum, 47 HP motor. Bottom Head #2: ~10" Dia. grooved rubber covered contact drum, 47 HP motor. Bottom Head #3: ~10" Dia. grooved rubber covered contact drum, 32 HP motor. Bottom Head #4: Finishing platen, 23 HP motor.Machine #2 - "KH2 CCCT 1350" 4r-Head Top Wide Belt Sander. Top Head #1: ~10" Diameter Grooved Steel Drum, 47 HP - 460 V motor. Top Head #2: ~10" Grooved rubber covered contact drum, 47 HP motor. Top Head #3: ~10" Grooved rubber covered contact drum, 32 HP motor. Top Head #4: Finishing platen, 23 HP motor.Specifications: -- PC User interface for each machine. -- Sanding belt size: 53" x 103". -- 96" Belt conveyor in between machines. -- 20 HP Vacuum Blower for each machine's vacuum bed.

COSTA KH2 CCCT 1350 Wide Belt Sander, (4) Heads52" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Steel contact roll, 9-7/8" dia, 45 HP motor;2nd Head: Rubber covered contact roll, 9-7/8" dia, 45 HP motor.3rd Head: Rubber covered contact roll, 9-7/8" dia. 60 shore, 30 HP motor.4th Head: Finishing Platen, 23 HPSpecifications: -- 53" x 103" Abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking. -- Controls with PLC processor, -- Pneumatic grit compensation with 4-position stops. -- Variable feed speed conveyor with inverter control 16 - 82 FPM.Equipped with & Features -- a Vacuum conveyor bed assembly with a 5.5 HP suction fan and motor. -- Infeed & outfeed spring loaded hold down shoes on all heads. -- Powered raise & lower conveyor bed with LED readout and motor load meters.

COSTA K6 WCCT 1350 4-Head Planer / Sander 4-Head with Planer, Drum, Drum and Combination headSpecifications: -- Front head #1 54" Helical planer head with (480) insert knives 34 kW or 45 HP motor. this is a removable head complete with cart for cleaning and changing knives. -- Head #2 Drum currently set up with 100 grit abrasive sanding belt 22 kW or 30 HP motor., -- Head # 3 Drum with 150 grit abrasive sanding belt 17 kW or 22 HP motor. -- Head # 4 Combi head with timed air bladder platen, currently runs 180 grit abrasive sanding belt, 14 kW or 20 HP motor. -- Feed mat speed from 4 - 20 feet per minute. Features: -- Capable of planning off 1/8" and sanding to 180 grit in one pass. -- Uses 52 - 54" x 103 abrasive sanding belts. -- Vacuum feed mat only surfaced 2 or 3 times, PLENTY of life left in it. -- Used in small shop running no more than 5 -10 hours a week, on a machine designed to run 3 shifts. -- Features Air scrubber unit on the out feed to remove any additional dust. Note: Machine was purchased New in February 2016

COSTA K7 CCCT 650 ... 4-Head Wide Belt Sander, working width 650 mm (25.6") and constant pass line conveyor heightExcellent Veneer and Solid wood sander with (3) Contact rollers and (1) platen.Head Configuration: -- 1st Head: Steel contact roller, 250 mm (9-7/8") diameter, driven by 37 kW (50 HP) motor. Abrasive belt speed 24 m/Sec (78 FPS). -- 2nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 30 kW (40 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 22 kW (30 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3rd Head: Segmented finishing platen, electronically controlled narrow segments conform to panel width and length for thin veneer sanding. Driven by 11 kW (15 HP) motor. Abrasive belt speed infinitely variable 3 - 16 m/Sec (30 - 52 FPS). -- Sanding Belt Info: abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking on all heads. Grit set system for abrasive belt grit compensation. -- At Outfeed: Brush Roller 180 mm (7") driven by 1.1 kW (1.5 HP) motor. Equipped with: -- PLC processor controls with touch screen. Integrated control cabinet. -- Feed System & Conveyor Bed: Min/max. working height 3 - 160 mm (1/8" - 6-5/16"). Variable feed speed conveyor with inverter control 4 - 20 m/Min (13 - 65 FPM). Constant Pass Line at 920 mm from floor (36"). Vacuum conveyor bed assembly. Infeed & outfeed spring loaded hold down shoes on all heads. Powered raise & lower of conveyor bed with LED readout.Also inculed: about $15,000 of sanding belt

Costa 60CT2-1150 (2)-Head, Wide Belt Sander44" width cap Drum, Combination HeadHead Co figuration 1st Head: Rubber-covered contact roll, 20 HP motor;2nd Head: Segmented polishing platen, (30) narrow segments are electronically controlled to conform to the panel shape and size to minimize veneer sand-throughs, each segment with variable pressure control, 15 HP motor.Specifications: -- Adjustable contact roll for varying thickness of abrasive belts with -- 45" x 103" Abrasive belt, electronic tracking. -- Motorized part thicknessopening on conveyor bed with digital readout, -- Variable feed speed 10 - 50 FPM with inverter drive, -- Vacuum conveyor bed assembly with 4 HP suction fan,infeed & outfeed spring loaded holddown rolls.Equipped with & Features: -- Controls mounted on the front of the machine, -- Instant shut-down safety guard, all motors with Y-Delta starters, and motor load meters.NOTE: Some spec's need to be verified

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP100 Can Flattener --220V, 1200 lbs per hour --Infeed Conveyor --Magnetic Separator -- New belt included

CRAFTSMAN DP-65 Drill PressSpecifications: -- Capacity: 15" -- Motor: 0.33 HP Equipped with: -- Push button control -- Stand

CRAM-A-LOT - SCR-T2-34: ...34-Yard Self-Contained CompactorsSpecifications: -- Cylinder: (2) 4". -- Main motor: 10 HP. -- Feed opening: 41″ x 58″ (1,041 mm x 1,473 mm). -- Capacity: 34-Yard. -- Ram force: Up to 24 tons.

CRAM-A-LOT - HX-60: Closed Door Baler with Cart Dumper & Infeed ConveyorSpecifications: --The CRAM-A-LOT "HX-60 HH" & "HX" Series Balers are ideal for warehouses and designed for ease of installation, operation, and maintenance. -- CRAM-A-LOT® HH & HX Series Balers are: Built with extra Heavy-Duty construction; ideal for warehouses & recyclers who deal with large quantities of corrugated and paper products.Baler is designed for long hours of operation and can operate either manually or automatically with photocell control. Optional custom-engineered Feed Conveyors and Cart Dumper Systems efficiently control Baler feed rates for optimum performance in a complete Baling System.Standard Features include:ANSI Z245.5 Compliant: All Compactors meet or exceed ANSI Z245.5 safety standards.UL/CUL Listed Control Panels.UHMW Ram Shoes: Adjustable to assure straight tracking and readily replaceable, should the need arise.Oil Sight Gauge: Oil level at a glance.Oil Filter: Replaceable "spin-on" cartridge to keep your oil clean.Heavy-Duty Controls: NEMA 4-Rated pushbutton controls with "key lockable" start switch.Automatic single-cycle operation. -- Bale Size: 60" x 30" x 40". -- Bale Weight: Up to (OCC) 1,400 Lbs. --Throughput: (OCC) 2-1/2 Bales /Hr. -- Cylinder: 7".