HURST 600 HP Waste Fired Boiler; -- Specifications:Complete in-place system with the following features: -- Decommissioned July 2019. -- 150 PSI. (300 PSI max wp), -- 20,700 Lbs per hour. -- Fuel House, Boiler Building and all Controls -- System has been "pickled" to maintain tube integrity.

HURST - SERIES 45. Boiler: Natural Gas -- SpecificationsBuilt New in 2016; Complete, never installed & ready to deliver! 207.5 HP; 60 PSI Hot Water; Natural Gas Fired Firebox. -- Efficient 3-pass design NATURAL GAS FIREBOX. -- ASME Code constructed & stamped for 15 PSI Stream: 30 - 100 PSI Water. -- Registered with: National Board of Boiler Inspectors. -- Easily maintained, designed for efficiency; large Furnace volume for ultimate combustion efficiency. -- Unified refractory base floor; steel skids; lifting eyes. -- Low heat release; Factory insulated. – 2"; Mineral wool, Factory jacketed & painted. -- Easy access to fireside surfaces; ample waterside clean-out openings -- Fully automatic operation; U.L. listed; forced draft Burners. -- Wet back construction. -- U.L. Listed controls & trim. -- Factory test fired, flame observation ports front & rear.Boiler Design. 3-Pass “FireBox"; design with: Stress relieving “Wetback"; fire tube construction.Hot Water pressures models are from: 8.5 - 415 HP; 100 PSI max.; 500 - 813 HP; 60 PSI max. built to Section-IV ASME Code.Hot water temperature not to exceed 250° F at or near the outlet of Boiler.Hot Water Model Trim. Safety relief valve; operating temperature control; high limit temperature control with manual reset; combination pressure & temperature gauge; low water cutoff control with manual reset.Hot Water Supply. 180 D/F Return: 160 D/F. -- Fireside Heating Surface: 830 Sq/ft. Furnace volume: 132 Cu/ft. Hot water outlet: 8"; hot water drain: 6"; drain connection: 2".Burner: Matched UL listed “forced draft"; power burners with: Factory pre-piped, wired, and tested fuel configurations for natural gas, propane (LP) gas, No. 2 (diesel) oil, or combination of both gas/oil.All units are Factory packaged with: Operating controls, relief valves, burner, and fuel train. Installation is made simple in that only service connections are needed to place in operation.High density 2"; mineral wool insulation assures lower radiant heat loss. In addition to meeting the requirements of U.L., Burner Systems are optionally available to meet the requirements of FM, IRI, Military, and others. -- Actual model: HURST S45 – G – 207.5 – 60W

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

IMPERIAL CM-006 Cartridge Modular Pulse Jet Dust/Fume Collector. Designed to be the strongest, safest, and most efficient dust and fume collector in the industry. -- Overall Specs: 4,800 CFM with 2,800 sq. ft. of total filtration media operating at 2.0:1 Air-Cloth-Ratio (ACR). Factory provided compressed air (clean - dried) is supplied to manifold mounted valves providing efficient continuous pulse jet Filter Cleaning System. -- Fan/Motor: MS-180-HD-70-20 Fan driven by 20 HP premium E motor. Efficient backward-inclined fan wheel. Manual slide gate damper on fan discharge. Fan-Silencer at fan outlet. Fan capable of 4,800 CFM at 13" SP. -- Electrical Control Panel: Nema 12 (indoor) enclosure with main breaker houses fan Start, E/stop, continuous On-Demand selector switch, Local/Remote selector. Soft Start drive to reduce power peaks on start up. -- Construction/Housing/Features: Heavy 7 - 10 gage construction with no external bolt holes guaranteeing no leaks for life. Filter access door with lockable handle, heavy duty latches for one handed operation. Tool-free filter change out with 'Even-Lock technology positive stop double sealed ensures cartridges are always installed properly. Filters are fully grounded to dust collector housing. OSHA compliant full length platform and adder access. Bolted support stricture with 54" clearance for 55 Gal drum & adapter.. Discharge via 10" Rhino heavy duty collection drum sealed cover kit requires not airlock with slide gate closure, tool-free sliding coupler, and grounding wire. -- Comes with: High Entry inlet with staggered angle inlet baffle plate provides filter protection and allows material to enter at filter level causing the natural downflow material primary separation effect. Horizontal square to round transition. DWYER DCT1000 control manages the Filter Cleaning System with user-friendly software menu. Solenoid time/on-off/settings and high/low differential pressure control capability Auto/Manual control option. Compressed air pressure regulator and filter. -- Optional: Updated control panel to include a Variable Frequency Drive (VFD) to replace the Soft Start drive and keypad on cabinet door. Upgrade Controls to Include VFD. VFD reduces inrush current at startup saving energy. Also regulates system airflow by maintaining static pressure at the collector inlet. This reduces the load on the motor saving operating cost, instead of dampening the airflow with an outlet damper that is required on other starter options. On system shut down the VFD slows the fan down to a preset speed of 20 HZ for 5 minutes (the duration of the down time cleaning cycle), this prevents dust from backflowing out of the collector due to the cleaning system pressurizing the collector creating a back flow through the ductwork. Please inquire for price.

IMPERIAL - CM-002: CMaxx™ Dust Collector The CMAXX™ was designed with revolutionary cleaning technology that insures maximum pulse cleaning power. The CMAXX™ housing is the largest in the industry with the lowest internal velocities. This large housing causes more dust to drop into the hopper before attaching to the filters. The low internal velocity combined with DeltaMAXX™ filters makes this the most efficient dust collector in the industry.Specifications -- 700 Sq./ft. Filter media; 2.55 - 1 air to media ratio. -- Main Handle Operator. -- Overload protection. -- NEMA 4 Enclosure. -- Push button start. -- Emergency stop button -- Run indicator light.Includes -- 7.5 HP Fan motor starter with: 1,790 CFM. -- Integrated DWYER - DCT1000 Control. -- Window kit for easy access to Dust Collector settings.

INDUSTRIAL RESOURCES PASS ONE Pallet DismantlerRemove stringers with a single stroke and dismantle 400 plus pallets per shift with "one" operator. -- Machine size; 14' L x 5' W, table size 54" L x 60" W. Stringer cap. 54". -- Includes; Hydraulic power pack, 7.5 HP, 12 GPM @ 750 psi. Manual variable speed valving. Hydraulic cylinder 2" bore x 62" stroke. -- Options Include; Upper arm lift to provide ease of maintenance, greater flexibility, table rollers to help simplify pallet handling and 60" pallet length. -- Cycle time in / out approx. 7 Sec.

INGERSOLL-RAND UP6-15C-125 15 HP Single-Stage Horizontal Tank-Mounted Rotary Screw Air Compressor, with 2,313 Hrs. (as of 2/16/24) Specifications: Cap. 55 CFM, Max. pressure 125 PSI. Pump speed 6,250 RPM. Sound level 69 dBA. Equipped with: High efficiency close coupled air end. Motor shaft-mounted centrifugal blower. Electronic stepper motor inlet air control. 2-Stage Air-cooled aftercooler. Total positive lubrication system, with Spin-on filter. Compartmentalized sound enclosure. Complete with: 80 Gallon Cap. 24” Dia. x 33” L Horizontal Air Receiving Tank. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

INGERSOLL RAND D144IN 85 CFM Non-Cycling Refrigerated Compressed Air Dryer Specifications: Cap. 85 CFM. Max. working pressure 203 PSI. Max. inlet temperature 60° C (140° F). Refrigerant type R-134A. Equipped with: Aluminum braze plate heat exchanger. Variable speed fan. Microprocessor control, with Graphic display, LED Dew point indicator, Energy saving mode, & History of last (10) alarms. Remote alarm signal terminal. High pressure switch. Fully-adjustable programmable electronic drain valve. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

INGERSOLL RAND D144IN 85 CFM Non-Cycling Refrigerated Compressed Air DryerSpecifications: -- Cap. 85 CFM. -- Max. working pressure 203 PSI. -- Max. inlet temperature 60° C (140° F). -- Refrigerant type R-134A.Equipped with: -- Aluminum braze plate heat exchanger. -- Variable speed fan. -- Microprocessor control, with Graphic display, LED Dew point indicator, Energy saving mode, & History of last (10) alarms. -- Remote alarm signal terminal. -- High pressure switch. -- Fully-adjustable programmable electronic drain valve.

INTERNATIONAL - MT-4843, ...Manual-Tie Horizontal Baler with Infeed ConveyorSpecifications: -- Cylinder: 8". -- Opening size: 60" x 46". -- Main motor: 40 HP.Equipped with: -- Control panel. -- Oil Cooler – Air-Over-Oil. -- 10' Bale Run-Out Table. -- High-Temp/Low Oil Level Shutdown. -- 48" x 43" x 60" Bale Size.

IBC - NA-1296A-48: Horizontal Closed-Door Baler Model -- 50 HP Motor. -- Main Cylinder: 10″. -- Bale Size: 30″ x 45″ x 60″. -- Hopper Size: 57″ L x 45″ W. -- Platen Pressure: 134 PSI. -- System Pressure: 3,000 PSI. -- Total Force: 235,620 Lbs. -- New cylinder installed approximately (6) months ago.

IBC - "IBC 4343 X 8 – 50 - 63": Horizontal Auto-Tie Baler -- Model: AT-4343-8-50-63. -- Type: Auto-Tie Baler. -- Motor: 50 HP. -- Cylinder Bore: 8";. -- Bale Size: 43"; x 43"; x Variable. -- Manufacturing Date: 2009.

IRONWOOD SLR 305 Straight Line Rip Saw Specifications: -- Width capacity of 18" and glue line tolerance up to 8'. -- Variable auto-lubrication system providing consistent lubrication to the chain track and automatically adjusting to the chain feed speed -- Minimum Material Length÷ 203 mm (8";). -- Material Thickness, Minimum- Maximum: 6.35 mm (0.25";) to 85 mm (3.35") -- Distance between Blade and Column 457 mm (18"). -- (8) Hold-down Rollers. -- Work Table Height 800 mm (31.5";). -- Saw Arbor Motor 15 HP. -- Saw Arbor Speed 4,500 RPM. -- Saw Blade Diameter 200-300 mm (8“ - 12“). -- Saw Arbor Diameter 25.4 mm (1";). -- Feed Speed 56 - 131 FPM. -- Feed Motor 2 HP.Equipped with & Features: -- Laser device to ensure straight line ripping entire length of the material. -- Maximum safety protection available with multiple rows of extended anti-kickback fingers and a side protection guard. Equipped with & Features -- (8) Accurately aligned pressure rollers extend from the cast iron machining head to provide absolute butting tolerances, low maintenance, and superior safety -- Solid steel cylindrical positioning rod and quick cam, cast iron fence provide accurate set-up, fast movement, and dust-free operations. -- Table Area (W x L) 950 mm (37";) x 1,450 mm (57";). -- Net Weight 2090 Lbs. -- Dust channel outlet (saw guard) 102 mm.

IRONWOOD SLR 305: straight line rip saw Specifications -- Width capacity of 18" and glue line tolerance up to 8 -- Variable auto-lubrication system providing consistent lubrication to the chain track and automatically adjusting to the chain feed speed -- Minimum Material Length÷ 203 mm (8 "; ) -- Material Thickness, Minimum- Maximum: 6.35mm (.25 "; ) to 85 mm (3.35 " ) -- Distance between Blade and Column÷ 457 mm (18 " )Equipped with & Features -- Number of Hold-down Rollers 8 -- Work Table Height 800 mm (31.5 "; ) -- Saw Arbor Motor 15 HP -- Saw Arbor Speed 4500 RPM -- Saw Blade Diameter 200-300 mm (8 “ -12 “ ) -- Saw Arbor Diameter 25.4 mm (1 "; ) -- Feed Speed 56 - 131 FPM -- Feed Motor 2 HP -- Laser device to ensure straight line ripping entire length of the material -- Maximum safety protection available with multiple rows of extended anti-kickback fingers and a side protection guard -- 8 accurately aligned pressure rollers extend from the cast iron machining head to provide absolute butting tolerances, low maintenance, and superior safety -- Solid steel cylindrical positioning rod and quick cam, cast iron fence provide accurate set-up, fast movement, and dust-free operations -- Table Area (W x L) 950 mm (37 "; ) x 1450 mm (57 "; ) -- Net Weight 2090 lbs -- Dust channel outlet (saw guard) 102 mm (4 " )

IRONWOOD SLR 305 Straight Line Rip Saw Specifications: -- Width capacity of 18" and glue line tolerance up to 8'. -- Variable auto-lubrication system providing consistent lubrication to the chain track and automatically adjusting to the chain feed speed -- Minimum Material Length÷ 203 mm (8";). -- Material Thickness, Minimum- Maximum: 6.35 mm (0.25";) to 85 mm (3.35") -- Distance between Blade and Column 457 mm (18"). -- (8) Hold-down Rollers. -- Work Table Height 800 mm (31.5";). -- Saw Arbor Motor 15 HP. -- Saw Arbor Speed 4,500 RPM. -- Saw Blade Diameter 200-300 mm (8“ - 12“). -- Saw Arbor Diameter 25.4 mm (1";). -- Feed Speed 56 - 131 FPM. -- Feed Motor 2 HP.Equipped with & Features: -- Laser device to ensure straight line ripping entire length of the material. -- Maximum safety protection available with multiple rows of extended anti-kickback fingers and a side protection guard. Equipped with & Features -- (8) Accurately aligned pressure rollers extend from the cast iron machining head to provide absolute butting tolerances, low maintenance, and superior safety -- Solid steel cylindrical positioning rod and quick cam, cast iron fence provide accurate set-up, fast movement, and dust-free operations. -- Table Area (W x L) 950 mm (37";) x 1,450 mm (57";). -- Net Weight 2090 Lbs. -- Dust channel outlet (saw guard) 102 mm.

NEDERMAN S-750 BAG FILTER Dust Collector w/ Auto Bag ShakerThe NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. With a 7.5 HP motor and a 4,500 CFM @ 6" WG it's the ideal solution for the small shop or single work-cell operation. -- Specifications: 7.5 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: 243 Sq/ft of filter media, easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 11". -- Available in 208/230 or 480 V, 60 Cy, 3 Ph. Must specify voltage at the time of orderIncludes: -- Auto Bag ShakerAvailable options:42 Gallons Drum Discharge - Single Drum (3 REQUIRED)230 Gallon Dump BinAvailable spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)

NEDERMAN - NFSZ 3000/1N. Modular Filter, fully-featured with: NRSZ-10 - Rotary Air Lock waste discharge; Spark Detection; Variable Speed motor drive7,320 CFM; Approx. 8-to-1 air-to-cloth ratio; positive pressure; expandable Heavy-Duty Baghouse Dust Collector System. - Designed for small to medium-sized air flows with: Large material concentration (dust loading).Specifications -- Total 915 sq./ft. filter area; (25) SUPERBAG 2000 XT15 filter bags. -- Includes: (1) Filter module sections (expandable) with: Combined explosion & access door in each section; each with 1.5 HP regenerative fans for cleaning of filter media. -- Unit is ATEX rated; Hopper for collected material to Rotary Air Lock at one end and discharging into a waste bin (not included). -- Equipped with: (1) Ground-mounted 40 HP TEFC Belt driven motor with Variable Frequency Drive and NEDERMAN MH type Blower package; about 18" inlet.Capable of approx.: 7,500 CFM w/drive guards; motor & fan are a common steel base/frame with current roof-mounted installation. - Main pipe to fan inlet is approx. 18", as is the fan outlet pipe. -- Features & Includes: Spark Detection system controlling an Abort Gate on return line and mounted on separate steel support; 22" dia. back pressure (flow) flap valve located between fan discharge & baghouse inlet. -- Complete with: Access ladder/platform; drain with plug: quick open access doors; inlet flange; electrical disconnect; separate control panel with motor starter for main blowers. -- Includes: Primary outside pipe; approx. 10' high support steel structure; platform & ladder mounted on top of structure.Baghouse dimensions: 48" x 94-1/2" Square (1,200 x 2,400 mm) for both modules; height of Baghouse shell will be provided.Actual model: NFSZ 3000 - 1N

NEDERMAN - S-1000: BAG FILTER Dust CollectorThe NEDERMAN S-Series Baghouse Dust Collector is: Quick to install and easy to operate. It is the ideal solution for the small shop or single work-cell operation. -- Includes: 10 HP Motor; CFM range from 4,000 CFM @ 8" WG to 5,000 CFM @ 7" WG. -- Equipped with: 10 HP - 1,750 RPM TEFC Motor; (24) Beane material filter bags; 230 Gallon Dump Bin: magnetic starter. -- Features: 360 Sq./ft. of filter medial; easy installation, typically (1) hour; quiet operation. -- Inlet opening 15". (2) Units available!

NEDERMAN S-750 Bag House Dust Collector7.5 HP - 1,750 RPM TEFC Motor. -- (24) BEANE material filter bags; (3) plastic waste collection bags; (3) clamps for easy removal of waste bags. -- Features: 243 Sq/ft. of filter media; easy installation typically (1) hour; quiet operation; (3) waste discharge points; 280 mm inlet. -- Unit is very versatile and capable of a nice range of operation; 2,500 CFM @ 10"Wg; 3,500 CFM @ 8"Wg; 4,500 @ 6"Wg. -- Magnetic starter included for 230 V - 3 Ph. -- 230 Gallon Dump Bin

NEWMAN/Cameron - KF-24: Dip Chain Gang Rip Saw with CAMERON "34H-M1" Infeed SystemSpecifications -- Saw Arbor: 24" Arbor cap.; 14" max. dia. tooling; 4" max. motorized thickness adjustment;22" min. length for glue joint accuracy; 6" throat. -- 2-13/16" Dia. arbor; 24-1/2" capacity saw sleeve arranged for 3-1/8" dia. bore saw blades; saw blade options: 10" - 14" Dia.; spacers: 4-5/8" dia. includes: (1) Saw sleeve and spacers. -- 75 HP - 3,600 RPM TEFC Direct drive motor; arbor with: Disc brake & load meter; arbor lockout on the access door. Feed & Chain: -- 5 HP Variable feed speed: 20 to 100 FPM with: Jam arbor protection. Dip bed carried on: 5" Pitch hardened Double-V chain; hardened dip cams; extruded structural aluminum feed bed slats with: Replaceable steel-backed rubber insert strips; automatic chain oiler with low level shutoff. -- (2) 4" Dia. air loaded overhead pressure rolls; spring-loaded overhead bed plate; pressure rolls & bed plate unit with motorized adjustment; slide type infeed guide with: Handle block; either side of the guide can be used for a stock engraver. -- Anti-kickback finger system with: (1) Lower & (2) upper on infeed; (1) upper kickback on outfeed. Equipped with & Features: Upper outfeed main dust hood: 7-7/8" Dia. 2,150 CFM Infeed dust hood 4-7/8 dia. (855 CFM). (1) Spare sleeve; (2) setup fixtures; generous array of spacers (see photos).