CAM-WOOD FSM-460AX Finger Joint ShaperSingle Finger joint Shaper with 8" min. and unlimited max. block length; 4" max. block thickness, maximum timber height to feed into assembly press is 3"; 18" max. block width (horizontal joint only); 18" table working width.Equipped with: -- Shaper spindle powered by 10 HP belt drive motor with 50 mm dia. spindle turning at 5,500 RPM; 160 mm (6.3") max. dia. cutter. -- Trim-saw powered by 5 HP direct drive motor at 2,850 RPM and a 1" dia. saw spindle; swings 180 mm (7") max. blade dia. -- Table cycles 2 to 4 per Min via the hydraulic system with a 2 HP hydraulic power unit. Includes 5" dia. dust outlet.Features: -- Manual Fingerjointer performs end trimming and shaping functions on right and left end of blocks. -- Air-operated clamp holding blocks firmly in place. After the workpiece is clamped, the table feeds past the saw and shaper spindles to perform trimming and finger-joint operations; trim saw cuts blocks exactly 90° ends. -- Shaper spindle is precision-constructed for cutting fingers accurately; swings up to 6" dia. tooling. -- Spindle height adjustment is displayed on the dial readout for easy adjustment. -- Table travels on a precision linear guide for stability; table traverse driven by hydraulic power system smooth and accurate block feeding. -- Variable feed speed permits proper feed for hard or soft wood. -- Cast iron frame and table for durability.

CONCEPTION CRP-180 Short Block Feeder Infeed ConveyorSpecifications: -- About 4 m long X 1.2 m wide, 2-ply rubber belt, friction back with Photocell for automatic operation -- Short Block Feeder; Blocks to be 25mm longer than width -- 14' rotating carousel with adjustable speed via VFD with Motorized wheel to avoid blockage -- Exit opening adjustable to the block width -- 200 mm x 7m long belt conveyor to carry the blocks to index rolls; Servo indexer controlling the flow powered by an electric motor; Speed-up belt powered by an electric motor -- Wane System: Scanner to detect wane integrated in conveyor -- Display screen to show wane detected; Kicker to kick blocks that are not in good orientation -- Conveyor to return it into the spreader belt conveyor -- Automatic Operations

GRECON PJ 150/500 and PF 10-610 Finger Jointer and PressFinger jointer and Press systemSpecifications: -- Grecon Finger Joint System Including: Model PJ 150/500 Shaper -- Trim Saw 5 HP -- Shaper Head 30 HP -- Glue Application Head -- Timber Width 30 mm - 159 mm (1.2" - 6.25") -- Timber Thickness 12 mm - 80 mm (.5" - 3.15") -- Timber Length 250 mm - 1780 mm (9.84" - 70") -- Infeed Belt Conveyor 20" Wide X 34" LongAfter the Finger joint shaper: -- Manual Roll Conveyor with Rotation for Turning Workpieces 22" X 68" -- Outfeed Belt Conveyor 20" X 39" -- Driven Roll Conveyor 20" X 120" -- Powered Belt Conveyor Prior to Press 7" X 86"Model Press PJ 10/6100 Finger Joint Assembly Press: -- Maximum Pressing Length 240" -- Cut-Off Saw Motor 3HPNote: The machine will be reconditioned upon placement of order.

INDUSTRIAL FINGER JOINTER 3870 SHAPER & FJA-100 ASSEMBLY MACHINE: Specifications: -- Model 3870 Dual Finger Jointer Shapers with feed chain speeds of 45 FPM via 5 HP fixed speed electric drive.Shaper is furnished with (2) 1-13/16” dia. 10 HP cutterhead spindles and (2) 5 HP trim saw motors and an automatic roll type glue spreader with pressurized glue tank. -- Production rates are: 60 lugs/Min with lugs on 9" centers and blocks up to 6” wide or 45 lugs per minute with lugs on 12" centers and blocks up to 8” wide. -- Shaper will accommodate blocks from 5-1/2” minimum to 48” maximum length x 1-1/2” minimum to 8” maximum width x 5/8” minimum to 2” maximum thickness. -- FJA-100 Finger Joint Assembly Machine with automatic operation and pneumatic pressure; assembles blocks up to 16’ long. The machine stops during the cut-off and press cycle. Variable feed speeds up to 100’ per minute. -- Offer includes a reconditioned Shaper Section, Assembly Machine, Glue Applicator, and Electrical System. -- This System requires (3) people to operate; (1) to feed the Shaper, (1) to inspect and transfer blocks to the Assembly Machine, and (1) to off-bear the Assembly Machine. -- All equipment will be checked out completely including, but not limited to, all motors being megged and tested, all bearings reviewed and replaced where necessary, the chains, rails, and hold downs reviewed and replaced as needed. -- The buyer is encouraged to inspect the machine and test run their parts when the reconditioning has been completed. Requires buyer's material prior to the run off. -- Cutterheads and tooling are not included but can be supplied at additional costNOTE: -- APQUIP Gluing System can be adapted to this System. Cost is unknown at this time. -- Delivery is approximately (8 - 10) weeks after receipt of deposit. -- Payment Terms: 50% deposit with order, 40% upon completion of successful run-off, balance upon completion of run-off.

NELSON ATKINSON FJ-728 Low Production Finger JointerComplete with self-feeding table with holddown clamps, hydraulically stroked past trim saw and cutterhead.Specifications: -- Trimsaw powered by 3 HP direct drive, 3,600 RPM arbor motor; uses 8" dia. blade. -- Shaper with 7-1/2 HP spindle motor, 1-1/4" spindle, 7" vertical spindle travel, 6-3/4" cap. under nut. - (4) spindle speed settings of 3,500 - 6,500 - 8,000 & 10,000 RPM, reverse rotation switch, 45" x 35" table, 12-1/2" max. tooling dia.; 36" table height. -- Includes cutter guard, dust outlets, self-braking motor, spindle lock, emergency stop and motor control center for all motor and electrical functions. -- Finger Joint Assembly Machine complete with material clamps and squeeze press. Assembles a pair of joints per cycle; operator "steps" the assembled length past the automatic cutoff saw.When a length stop is contacted by the assembled length, the cutoff saw fires, cutting up from under the table, and the finger jointed board is cut to its specified lengths. Long lengths can be assembled by relocating the length stop. -- Tooling: (1) finger jointer cutterhead aboput 5/8" finger length and (1) each carbide tipped Retrim and Cutoff Sawblades., (1) glue nozzle with glue pump

For dumping (1) load at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. The cradle holds the box as it is pivoted up to 135° to the final dumping position. The cradle is pivoted with a hydraulic cylinder driven by a 3 HP hydraulic pump. The cylinder is manually energized via operator foot-switches. -- System includes all mechanical equipment, electric powered hydraulic pump, and (2) foot switches. All wiring and controls by others. ~ Accepts a standard 96" long X 60" wide X 60" high box.

For dumping (1) load of fingerjoint blocks at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. -- 3-Sided cradle will hold the box or pallet when it is pivoted up to 135° to the final dumping position; cradle opening is 88" long X 48" wide X 50" high. -- A pair of replaceable forks hold pallets in place in the cradle. The cradle is pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the fingerjointer operator with foot switches. -- Scope of supply includes all mechanical equipment, electric powered hydraulic pump, and two foot switches. All wiring by others.

For dumping (1) load of fingerjoint blocks at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. -- 3-Sided cradle will hold the box, pallet, OR unit when it is pivoted up to 135° to the final dumping position; cradle opening is 88" long X 48" wide X 50" high . -- A pair of replaceable forks hold pallets in place in the cradle. The cradle is pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the fingerjointer operator with foot switches. -- Scope of supply includes all mechanical equipment, electric powered hydraulic pump, and two foot switches. All wiring by others.