LAWECO HEAVY DUTY Scissor LiftSpecifications: Very Heavy Duty hydraulic Scissors Lift with 12,000 Lbs. capacity. -- (2) 6" lifting/lowering cylinders. -- Platform size 64" x 142", approx. 19" lowered and approx. 85" raised height. -- No hydraulic unit or controls.(2) Units available, chain conveyor on one can be removed @ N/C

LEADERMAC MODEL LMC-1300M – 51"; GANG RIPSAW -- Specifications: -- Width capacity: 0.6"; to 51"; -- Thickness capacity: 0.4"; to 4"; -- Up & Down motor: 1 HP -- Feed motor: 7-1/2 HP with VFD -- Saw Spindle HP: 75 HP, larger motors are optional - see below -- Saw Spindle diameter: 3.15"; (80mm) double keyed -- Spindle RPM: Std. 4,000 RPM. 5,000 RPM optional with 10"; Blade capacity -- Saw blade Diameter 12"; diameter for 4"; thick material -- Feed speed, Infinitely variable: 20 To 50 FPM. 100 or 200 FPM optional -- Standard Features & Equipment: -- Extra Heavy Main Frame – Stress Relieved -- Sound & Safety enclosure included – with internal strobe-free lighting -- High Precision Spindle - Double Keyed assembly with Hydro-Loc outboard bearing assembly on outboard side -- Entire Spindle assembly slides out on support for Quick, Easy and Precision Saw Setting & Changing -- Hardened & Hard Chromed Infeed Table -- (7) Sets of Top Power Driven Rolls – full width -- (5) Sets Bottom Power Driven Rolls – full width -- Infinitely Variable Pneumatic Pressure to Top Feed Rolls -- Top & Bottom Feed Rolls are all Driven by Cardan Shaft Drive with HD Gearboxes interconnected -- 1st Top & 1st Bottom Powered Roll Combination and then 2 Rows Anti Kick Back Finger Units – Full Width and then to the rest of the Powered Top & Bottom Rolls giving you the best Feeding Capability with good safety Features -- HD VFD – 7.5 HP Feed System – Infinitely Variable -- Main motor has Wye-Delta low amperage soft start -- Electrics are 230, 450 or 575 volts 3/60 with all controls to CSA/UL Specifications -- Documentation: Maintenance manual, Operation manual, Electrical diagrams, Parts list & Tool Box (Electronic Version on Request) -- (4) Top & (4) Bottom 6"; Dust hoods included -- Saws, Dado Heads &/or cutterhead(s) and spacers optional extra -- Price Includes: -- Hanging Control Panel – in lieu of Control standard setup as shown in machine photo -- Moveable Main Electrical Panel with 10 ft. of main cable -- Amp Meter for the Arbor Motor -- 4"; thickness Capacity – using 12"; or 14"; diameter blades Available at extra cost: -- Adjustment of the Rear guide with digital readout from the front of the machine (only desirable if Side Heads are supplied) -- Additional Side Pressure Roller System on the Infeed Table of the Machine -- 100 HP saw spindle motor -- 125 HP saw spindle motor -- 150 HP saw spindle motor -- Scoring Saw Arbor ahead of main saws if desired -- Saw Spacers for Main Arbor quick Setup -- Mechanical Quick Lock Saw collars if desired for independent saw setting -- Spare Spindle Assembly, complete, including Drive Side Bearing Assembly with support slide and roller transfer support assembly per photo for preloaded saws, add $ 13,045 -- Questions? Call Jeff @ Ext 349!

LEADERMAC MODEL LMC-1600M - 63"; GANG RIPSAW Specifications: -- Width capacity: 0.6"; to 63"; -- Thickness capacity: 0.4"; to 2"; (thicker material processing is available as an option) -- Up & down motor: 1 HP -- Feed motor: 15 HP HD VFD -- Feed speed, infinitely variable: 20 - 200 FPM. -- Feed direction from Right to Left is standard -- Saw Spindle HP: 150 HP, Wye-Delta low amperage soft start (larger motors are available as an option) -- Saw Spindle diameter: 3.15"; (80 mm) double keyed -- Saw blade Diameter 12"; diameter for 2"; thick material -- Spindle RPM: Std. 4,000 RPM. 5,000 RPM optional with 10"; Blade capacity Standard Features & Equipment: -- Extra Heavy Main Frame – Stress Relieved -- Sound & Safety enclosure included – with internal strobe-free lighting -- High Precision Spindle - Double Keyed assembly with Hydro-Loc outboard bearing assembly on outboard side -- Entire Spindle assembly slides out on support for Quick, Easy and Precision Saw Setting & Changing -- Hardened & Hard Chromed Infeed Table -- (7) Sets of Top Power Driven Rolls – full width -- (5) Sets Bottom Power Driven Rolls – full width -- Infinitely Variable Pneumatic Pressure to Top Feed Rolls -- Top & Bottom Feed Rolls are all Driven by Cardan Shaft Drive with HD Gearboxes interconnected -- 1st Top & 1st Bottom Powered Roll Combination and then 2 Rows Anti Kick Back Finger Units – Full Width and then to the rest of the Powered Top & Bottom Rolls giving you the best Feeding Capability with good safety Features -- HD VFD – 15 HP Feed System – Infinitely Variable -- Main motor has Wye-Delta low amperage soft start -- Electrics are 460 volts 3/60 with all controls to CSA/UL Specifications -- Documentation: Maintenance manual, Operation manual, Electrical diagrams, Parts list & Tool Box (Electronic Version on Request) -- (8 - 4) Top & (4) Bottom 6"; Dust hoods included -- Saws, Dado Heads &/or cutterhead(s) and spacers are optional at extra cost.Price Includes: -- Pedestal for all controls, on a 11 meter long cable to get around the front right (infeed side) of the ripsaw -- Moveable Main Electrical Panel with 10 ft. (3m) of main cable -- 150HP Saw Arbor Spindle motor in lieu of std. 75HP -- Pneumatic hold over on infeed table to hold wide, and allow holding over of narrow boards up to the fence -- Increased Feed Speed to 200FPM (60mpm) includes Heavier gearboxes and drive components) with 15 HP VFD -- Amp Meter for the Arbor Motor -- Faster removal speed for the arbor assembly (50% faster than standard machine) -- 1 Spare complete New Design Spindle Assembly including Drive Side Bearing Assembly with support slide and roller transfer support assembly per photo for preloaded saws Extended length per discussion.(1 only unit included in price of machine, this is for a 2nd cart and spindle assembly- total of (2) will come with the machine – additional units available, see below) -- Schneider / Telemecanique VFD drive unit

LEADERMAC LMC-101-900 HD 36" HD Multi-Blade "Roll Feed" RIP SAWSpecifications: -- Working width: 0.6"; – 36"; -- Working thickness: 0.4"; – 4"; -- Up & Down motor: 1 HP -- Feed motor: 7-1/2 HP with VFD -- Spindle HP: 75 HP, larger motors optional -- Spindle diameter: 3.15"; double keyed -- Spindle RPM: Std. 4,000 RPM, 5,000 RPM optional -- Saw Blade Diameter, 14"; diameter -- Feed speed, infinitely variable: 20 – 50 FPM, 100 or 200 FPM optionalStandard Features: -- Extra Heavy Main Frame – Stress Relieved -- Sound & Safety enclosure included – with internal strobe-free lighting -- High Precision Spindle - Double Keyed assembly with Hydro-Lock outboard bearing assembly on outboard side -- Spindle assembly slides out on support for Quick, Easy and Precision Saw Setting & Changing -- Hardened & Hard Chromed Feed Tables -- (7) Sets of Top Power Driven Rolls – full width -- (5) Bottom Power Driven Rolls – full width -- Infinitely Variable Pneumatic Pressure to Top Feed Rolls -- Top & Bottom Feed Rolls driven by Cardan Shaft Drive with HD Gearboxes Interconnected -- 1st Top & 1st Bottom Powered Roll Combination and then (2) Rows Anti Kick Back Finger Units Full Width and then to the rest of the Powered Top & Bottom Rolls provide the best Feeding Capability with excellent safety features -- HD VFD – 7-1/2 HP Feed System – Infinitely Variable -- Main motor has Wye-Delta low amperage soft start -- Electrics are 230, 450 or 575 volts 3/60 with all controls to CSA/UL Specifications -- Documentation: Maintenance manual, Operation manual, Electrical diagrams, Parts list & Tool Box (Electronic Version on Request) -- (8) Dust outlets consisting of (4) top & (4) bottom 6"; diameter dust hoods -- Saws, Dado Heads &/or cutterhead(s) and spacers optional extra Options Included In Price: -- Hanging Control Panel – in lieu of Control std. setup as shown in machine photo, Included -- Moveable Main Electrical Panel with 10 ft. of main cable, Included -- Amp Meter for the Arbor Motor, Included -- 4"; Thickness capacity in lieu of standard 2"; thickness, Included Available Options: -- To 3" Thickness Capacity – using 12"; blades, P.O.R. -- To 3"; or 4"; thickness Capacity – using 14"; blades, P.O.R. -- To 100 FPM Top Feed Speed – Infinitely Variable – 4"; Thickness Capacity, POR -- To 200 FPM Top Feed Speed – Infinitely Variable – 2"; max. Thickness, P.O.R. -- 100 HP saw spindle motor, P.O.R. -- 125 HP saw spindle motor, P.O.R. -- 150 HP saw spindle motor, P.O.R. -- Front or Rear 10 HP Side Heads (Please discuss if interested), P.O.R. -- 15 HP or 20 HP Side Head motors in lieu of 10 HP, P.O.R. -- Adjustment of the Rear guide with digital readout from the front of the machine (only desirable if Side Heads are supplied), P.O.R. -- Scoring Saw Arbor ahead of main saws if desired, P.O.R. -- Saw Spacers for Main Arbor quick Setup, P.O.R. -- Mechanical Quick Lock Saw collars if de

LEADERMAC SYC 300M Heavy Duty Roll Feed Ripsaw: Features & General Description: -- Cast Iron base with easily accessed Anchor Bolts; lift up sound enclosure with light for quieter and safer operation; Hydro-Loc Outboard Bearing System for best gang sawing shaft support, includes grease gun; HD Cardan shaft feed (chainless) drive throughout. -- (6) Full width, close coupled driven top feed rollers; (4) full width driven bed rollers; top rolls are air tensioned; variable pressure controls on top feed rolls; motorized lift to top rolls; infeed table is hard chromed with approx. 0.012"; - 0.014"; chrome. -- Easily adjusted roll holdover on the infeed table; saw spindle has motorized lift and lowering; multiple HD V-belt driven saw spindle with special HD belt tensioner; saw blades cut from below, hence better dust removal and a heavier sturdier design. -- Saws are pre-mounted on a slip-on sleeve for quick change; (3) sets of anti-kickback devices included; central lube system; pneumatic pressure controller safety switch – if air pressure to the top rolls drops below the set to run level, the feed will automatically stop. -- Controls include: VFD Control to feed speeds and Digital Speed Readout in FPM or MPM; TECO-WESTINGHOUSE main electric motor; I.E.C. – TELEMECANIQUE-SQUARE-D Electricals meet or exceed UL/CSA Standards. -- Machine is equipped with WYE-DELTA Soft-Start (low Amperage) starters & main disconnect, multiple “E-Stops" operate at low amperageSPECIFICATIONS: -- Max. thickness, 5.1"; (130 mm); Note – to 4-1/2"; with std. 14"; diameter blades; to 5.1"; with optional 16"; Blades. -- Saw sleeve usable length of 12.3"; (312 mm) - max. dist. between outside saws; minimum length material, 10"; (250 mm) – at slower speeds. -- Saw Blades with 10"; min. to 14"; max dia. x 70 mm Bore (double key), 16"; (400 mm) optional – no charge; Saw spindle with 50 mm dia. runs at 3,200 RPM; Saw sleeve – included, 70 mm OD with double keyways. - Includes (1) set of spacers. -- Main Motor – 75 HP (50, 60, or 100 HP optional); top feed rolls – rise & fall, 1 HP; Feed Drive of 7.5 HP with VFD infinitely variable speed control, 20 to 165 FPM (6 to 50 MPM) to 200 FPM – 60 MPM – optional). -- (4) 150 mm Dust collection outlets; approx. weight – net, 5,060 Lbs.; WYE-DELTA – low Amperage - Soft Start for main motor starter; electrics to UL/CSA Standards and wired to 230/460 or 575/3/60. - Note: Stock machines are with 50 HP – 460/3/60 electrics machine and can be easily and inexpensively transformed to other voltages.Optional Extras. -- 75 KVA Auto Transformer to run machine on 230/3/60 electrics, please add ...$ 2,045. -- 16"; (400 mm) Dia. blade with 5.1"; max. Thickness N/C; NOTE: – Contact us to see if stock machine has this capacity. -- Extra Saw Sleeve, add ...$ 995. -- Additional Sets of spacers for saw sleeve, P.O.R. -- 20 MW Laser & Laser Holder w/12"; Bolt o

ORIGINAL 3579-16L Metal Cutting Radial Arm Saw (Super Duty Series)The Super Duty Series is the ultimate workhorse of the industry, capable of operating 2 to 3 shifts per day. Miter & bevel cutting, compound miters and dado operations. Constructed of heavy duty cast and ductile iron for vibration free operation.Specifications: -- 7.5 HP TEFC Saw motor; 16" dia. blade; 1" x 3-1/8" saw arbor; 5" thickness cap. @ 90°, 2" @ 45° bevel; 32" crosscut cap.; 21-5/8" max. miter cut @ 45°. -- Features: -- Swivel arm for miter cuts, swivel motor for bevel cuts; indexing yoke to 90° for rip cutting panels; saw head with automatic motor brake and manual chain feed assembly; positive locking device for tilting; upper and lower blade guards with anti-kickback attachment. -- Complete with: -- The Metal Cutting Series comes with the standard t-slot aluminum extruded top, allowing easy to attach aluminum fence, clamping systems, table surface options, as well as your own clamping jigs or cutting fixtures. These all come mounted to a extruded leveling frame for easy leveling of the entire table assembly throughout the life of the machine. -- Available Options: -- Power feed saw head; pneumatic clamping systems; Mist Coolant System (manual for non-ferrous cutting); blade.

ORIGINAL 3546 RADIAL ARM SAW (Heavy Duty Series)The Heavy Duty Series is a very precise machine made for the rigors of every day industrial use. Straight, miter, bevel and compound bevel cutting in a heavy gauge steel powder coated frame & legs. Specifications: 5 HP TEFC Saw motor; 16" dia. blade; 1" x 2-3/16" saw arbor; 4-15/16" thickness cap. @ 90°, 2" @ 45°; 24" crosscut cap.; 15-1/2" max. miter cut @ 45°; 37-7/8" rip capacity. Features: -- Swivel arm for miter cuts, swivel motor for bevel cuts; indexing yoke to 90° for rip cutting panels; saw head with automatic motor brake and automatic spring return; positive locking device for tilting; upper and lower blade guards with anti-kickback attachment. Complete with: -- 42-1/2" x 31-1/4" MDF table; sturdy powder coated cast iron frame; heavy gauge steel base and support legs.

ORIGINAL 3551 RADIAL ARM SAWThe "Original" Radial Arm with a full 24" crosscut capability. -- Sturdy cast iron frame for saw head and arm.Equipped with: -- 5 HP single-phase motor with magnetic starter and overload protection. -- Saw head with automatic motor brake and automatic return. -- Positive locking device for tilting. -- Large 49" x 50" MDF table. -- 16" Blade cap. with a 4-3/8" material thickness at 90°. -- Features: -- Heavy gauge steel base & legs for solid support. -- Complete upper & lower blade guards and anti-kickback attachment.

ORWAK - 5070-HDC, ...Dual-Chamber Vertical BalerSpecifications: -- Bale size: 28" x 20" x 28" -- Press force: 6,600 Lbs -- Cycle time: 36 Sec -- Noise level: < 70 dB -- Bale weight: Up to 190 Lbs -- Plastic weights: Up to 220 LbsEquipped with: -- Dual-Chamber

OVERBUILT MODEL 10 CAR CRUSHER -- (2) 10" Cylinder -- Height 10 Ft (raised) , 24" ( lowered) -- Width 7'6" -- Length 20'3" -- Lid movement ( Travel) 8 feet -- Hydraulic cylinder 10" x 4" rod x 96" travel -- Pressure 2,400 psi -- Crushing force 159 tons -- Approx 3,800 hours -- John Deere Engine

OVERBUILT - 10 HS Portable, ...Car CrusherSpecifications: -- (2) 10" Cylinders. -- Height: 10 ft. (raised); 24" ( lowered). -- Width: 7-1/2'. -- Length: 20-1/4". -- Lid movement: 8 ft. (Travel) -- Hydraulic cylinder: 10" x 4" Rod x 96" travel. -- Pressure: 2,400 PSI. -- Crushing force: 159 Tons -- Resealed Cylinders.

PRS H-SERIES Pallet StackerPRS pallet stacker can handle pallets ranging from 30" to 60" squares, 5 HP hydraulic power unit, 40 PSI air supply required, anti-tip bars, infeed timer logic system, programmable stack eject. -- Complete with: Live infeed, automatic pallet stacking and automatic stack discharge, capacity of (7) pallets per minute, requires 7' x 7' floor space.PRICING SUBJECT TO CONFIRMATION.

PRS MODEL T Pallet StackerSpecifications: -- Fixed 48x40 -- Hydraulic Lift and Chain Conveyance -- Fully Automatic -- Programmable Stack and Eject -- Factory Refurbished Fall 2022

PEERLESS - MONO 21 Unit , ...Material Chip BinChip Bin main components: -- Bin with 21-Unit (4,200 cubic feet) capacity. -- Hydraulic power unit. -- Steel support structure. -- Clamshell-type material discharge doors. -- Price shown includes dismantling & loading onto trucks. -- Infeed Conveyor shown is NOT included, but is available as an optional item.

PIQUA - PW72-50, Semi-Automatic Wide-Mouth Horizontal Baler with MAX-PAK ConveyorSpecifications: -- Cylinder: 7" -- Main motor: 30 HP -- Bale size: 48″ x 36″ x 72″ -- Feed opening: 46" x 50" -- Cycle time: 20 Seconds -- Platen force: 86,600 Lbs -- Bale weight: 1,500 – 1,800 Lbs -- Door cylinder: 4" -- Door cylinder stoke: 12"; -- Conveyor belt: 60"Equipped with: -- 60" Infeed Conveyor with rubber belt.NOTE: New Conveyor rubber belt, paint, and safety stickers.

PNEUMAFIL 13.5-460-8 Reverse Air Dust Collector System;Reverse Air Dust Collector with 42,600CFM at 9 to 1 air cloth ratio, 4,738 square feet of filter area. -- 13-1/2' Dia. round baghouse contains (460) bags - 96" long by 5" dia. filter bags in galvanized cages w/reverse jet bag cleaning. -- Reverse Air from 15 HP blower motor which cycles once a minute over filter bags (rotating plenum covers each row of bags once a minute, reversing the normal air flow direction. -- Reverse Air action back flushes the bags and dislodges wood dust particles collected on the filter media which then fall to the bottom of the 60° funnel hopper for removal), bags are changed via walk-in door.. -- Material handling fan with approx. 48" inlet dia with 150 HP floor mounted motor (covered in a shed); 0.25 HP explosion proof motor for manifold drive. -- Rotary Air Lock, gearmotor driven at the bottom of the hopper feeding and shared horizontal screw type auger (if you want it) with gearmotor drive. -- Features: MOTOTRONICS Soft Start for main motor. FIRETEK Spark Detection System (subject to prior sale with adjacent unit). -- Includes: Explosion doors, sprinkler pipe, interior electrical control panel, support frame, safety ladder, railings, and exterior ductwork.Professional dismantling, rigging, transport and installation is available.NOTE: Unit being sold under this record is pictured on the left side on the first two photos. For the smaller diameter unit on the right side (DIXIE AIR) see record "DO-011266".

POWER PACK CONVEYOR - 32' x 58" Heavy-Duty, ...Inclined ConveyorSpecifications: -- Conveyor size: 58" x 32' -- Adjustable discharge height: 11' to 14'

POWERMATIC Turbo Cone Dust Collector with Twin Canister Filter Kit;Complete with the following features: -- 3 HP 3 PH Material Fan, -- Generates 1,782 CFM. -- Ships from Oregon Coastal region.

PRESTO XL36-20 Scissor Lift2,000 Lbs load capacity for evenly balanced load. -- 7-1/4" Lowered height. -- 36" Travel to raised height of 43". -- 17 Seconds travel time. -- Hinged platform for access to cylinders and internal power unit in collapsed position. -- 24" x 48" standard platform size. -- 3/4" Steel plate scissor legs. -- Heavy Duty hydraulic cylinders with chrome plated rams. -- Lifetime lubricated bearings on all rollers and pivot points. -- Electro-hydraulic 1 HP motor. -- Standard hand control pendant. -- Standard safety velocity fuses. -- Safety maintenance device.

PRESTO XL60-60 Scissor Lift6,000 Lbs. load capacity for evenly balanced load.Specifications: -- 10" Lowered height. -- 60" Travel to raised height of 70". -- 30 Seconds travel time. -- Hinged platform for access to cylinders and internal power unit in the collapsed position. -- 48" W x 96" L platform size, base 24" W x 86" L. -- 3/4" Steel plate scissor legs. -- Heavy Duty hydraulic cylinders with chrome-plated rams. -- Lifetime lubricated bearings on all rollers and pivot points. -- Electro-hydraulic 3.2 HP motor. -- Standard hand control pendant. -- Standard safety velocity fuses. -- Safety maintenance device.