CHAMPION - HRA25-25, ...Dual Stage Air Compressor. 25 HP Commercial Duty motor; 90.1 CFM at 175 PSI and 250-gal. horizontal tank. -- Features: CHAMPION's "R" Series 2-stage cast iron pump, dome pistons, and disc valves allow for higher performance at lower RPM's; largest roller bearings in the industry. -- The 250-gal. horizontal tank is equipped with: Large pressure gauge, standard tank drain, and a hard painted finish for years of durability. -- Complete with: Large dia. air filters, OSHA approved belt guard. -- Air-cooled aftercooler.

ELGI EN15-125 20 HP ENCAP Rotary Screw Compressor w/Tank & Dryer; 68 CFM @ 125 PSIG.ELGI's 20 HP Rotary Screw Air Compressor w/80 CFM Refrigerated Dryer mounted on a 120 gal. receiver tank.Equipped with: -- 20 HP motor operation up to 115°F ambient temperature; "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely.Includes: -- 120 Gal. receiver tank, 80 CFM Refrigerated Air Dryer; single-door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.

ELGI EN04-125 5 HP ENCAP Series Rotary Screw Compressor; 19.3 CFM @ 125 PSIG Equipped with: -- Efficient air filtration system where air enters through a pre-filtered enclosure. -- After cooler is standard on all models to enable high efficiency TEFC, Super E, 5 HP motor operation up to 115°F ambient temperature.Complete with: -- "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Includes service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely.Includes: -- 3-Stage efficient air-oil separation (less than 2 PPM). -- Single door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety. -- (230 volt, 1-phase option available).

ELGI EG75-125 Rotary Screw Air Compressor; 100 HP - 453 CFM @ 125 PSIG100 HP Rotary Screw Compressor, 450 CFM @ 125 PSIG(Direct Drive); Air-End equipped with "eta-V" profile rotors. -- Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty.

ELGI EN11-125 Tank Mounted Rotary Screw Compressor w/Refrigerated Dryer, 15 HP - 55 CFM @ 125 PSIGENCAP Series Screw Compressors:120 Gallon Tank Mounted with refrigerated dryer and filters - are designed to encapsulate all functional components and compressor within a common housing. With its small footprint, high reliability and low maintenance requirements, the compressors are ideal for all industrial applications where size, efficiency and cost matter.Equipped with & Features: -- 6 Year Airend Warranty -- Low Sound Enclosure -- Premium Efficiency NEMA motor w/F insulation -- TEFC Drive and Fan Motor -- High Ambient Oil Cooler for low operating temperature -- UL/cUL Certified Control Panel -- Controls & Indications: Microprocessor Controller includes -- Maintenance Schedules -- Pressure Transmitter -- Temperature Transmitter -- Auto Restart -- Remote Start / Stop -- Modulation and Load / Unload Controls -- Phase Monitor -- DCS Connection through Rtu/RS 485 Port

ELGI EG22V-125 Rotary Screw Air Compressor; 30 HP VSD - 132 CFM @ 125 PSIG30 HP Rotary Screw VSD (Variable Drive) CompressorEquipped with: -- Low Sound Enclosure -- Premium Efficiency NEMA Motor w/F Insulation -- TEFC Drive and Fan Motor -- Direct Coupled with Flexible Coupling -- High Ambient Oil Cooler for low operating temperature -- UL/cUL Certified Control Panel with Wye-Delta Reduced Voltage StarterMicroprocessor Controller Includes: -- Maintenance Schedules -- Pressure Transmitter -- Temperature Transmitter -- Auto Restart -- Remote Start / Stop -- Load / Unload Controls -- Phase Monitor -- DCS Connection through Rtu/RS 485 PortLIFETIME Air-End Warranty

ELGI EGRD 500 Refrigerated Air Dryer (480 CFM)The ELGi EGRD 500 refrigerated dryer is designed to provide a constant 41ºF dew point and utilizes the latest advancements in refrigeration technology to provide low operating cost and years of trouble-free performance.The advanced “ALU Dry"; aluminum heat exchanger module enables the packaging of the pre-cooler, evaporator, separator, and reheater all in one compact unit. This reduces the size, weight and pressure drop associated with conventional exchangers and optimizes the overall performance and reliability of the dryer which ensures effective removal of condensed liquids regardless of flow.Features: -- Microprocessor Controls with Dew Point Display Indication -- All-In-One Aluminum Design Exchanger -- Low-Pressure Drop -- Ozone Friendly Refrigerant -- De-Mister Type Moisture Separator -- Environmentally Friendly Refrigerant -- Hot Gas Bypass for Constant Dew Point -- Extended Service Life -- Timer Drain Options Include: The ELGi Premium Filter Series is constructed from premium materials and features with ease of installation and service in mind. Filter elements have a unique push-fit, double O-ring design to ensure no contaminants get down stream. Features: -- High Quality Aluminum Construction -- Automatic Internal Float Drain -- Pop-up Filter Change IndicatorPrice ...$ 800.00

ELIO VALERI ELVAP 120 Copy Lathe. -- General data: 48" max. length cap., 7" max. dia. without steady rest, 3.93" max. dia. with steady rest, and up to 2.5" x 2.5" dia. with steady rest for square pieces; 0 - 39 FPM forward and 0 - 52 FPM return speed, 5.5 HP motor, 1,300 - 3,500 - 5,000 RPM; -- Features: Air/oil feed and copier, chain head stock drive, gate loading, pattern; pneumatic tail stock, automatic pneumatic control program.

EMC VENUS 1300 1K ... Finishing Sander with (1) Sanding Head: Combination Head.Useful working width 1,300 mm (51"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").Working Unit: Combination Roller & Pad. -- Roller diameter 142 mm (5-5/8"). Rubber covered hardness 85 Shore. Roller pressure adjustment control & "Grit-set system". Main Motor On Off Selector control with pneumatic piston to select roller, 22 kW (30 HP) Automatic star-delta starter Rotating cutting speed: 18 m/Sec (59 FPS). -- PNEUMATIC Controlled Flexible Sanding Pad Including On-Off Selector: Quick Change System: Removable pad with felt, rubber and graphite. Rotating cutting speed 18 m/Sec (55.8 FPS). Abrasive belts oscillation by means of electronic photocell sensor.Feed system:CONSTANT PASS LINE - fixed infeed height 900 mm (35") from floorIdle table rollers support in infeed and outfeedRubber covered presser rollers, groovedVariable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM). Inverter ControlledLarge diameter screws on machined guides with columns and pistonsAutomatic feed belt centering deviceElectronic digital display for working thicknessGeneral Machine Features: -- Analog ammeters on main control cabinet. -- Electronic motorized grit set system, control from touch screen.Electronical Panel: -- Check Control Self Diagnostics with Alarm Control. -- Analog Ammeter on the main control cabinet. -- Infeed table thickness system electrically controlled. -- Independent Overload protection.Safety: -- Infeed front emergency swinging bar for oversized panels. -- Infeed protection pressing blade to avoid pieces to go back to operator. -- Rear and front emergency push buttons. -- Automatic brake on abrasive belts motors. -- Automatic emergency stop and alarm display in case of: &#9679 Low Air Pressure. &#9679 Doors opened ("easy maintenance and inspection"). &#9679 Electric motors overloading. &#9679 Emergency detector for over thickness material cut. &#9679 No tension on abrasive belt. &#9679 Abrasive belt lateral mistracking. &#9679 Abrasive belt broken.Idle table rollers support in infeed and outfeedCentralized Control Cabinet: &#9679 IP 54 protection against dust & moisture. &#9679 Analog ammeter on main control cabinet. &#9679 Table lifting-lowering thickness system electrically controlled. &#9679 AUTOMATIC Delta - Star starter on abrasive belts motors. Centralized independent pneumatic control cabinet: &#9679 IP 54 protection against dust & moisture. &#9679 Pneumatic air filter with automatic water-drain system. &#9679 Pneumatic adjustment for "Grit set system". &#9679 Pneumatic plant working without lubrication. &#9679 Compressed air pressure 6 bar (85 PSI). Options Available: Tampico Brush natural fiber brush for cleaning of the pieces, diameter 150 mm (6"). Motor Power 1.1 kW (1.5 HP). $3,950

EMC MERCURY 1350 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pneumatic pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,350 mm (53"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 2,200 mm (86-5/8") x (width) 1,320 mm (52"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 180 mm (7"), spirally grooved. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- Motor power 11 kW (15 HP) driving both heads, with soft starter. -- On/Off Selector control with pneumatic piston to select roller. -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 140 mm (5-1/2"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- New pneumatic aluminium sanding pad, lamina 40 mm. With On/Off selector. -- Quick Change System for removable pad with felt, rubber and graphite. -- Rotating cutting speed 18 m/Sec (59 FPS). -- Driven by same main motor, with soft starter.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). -- Table rollers. Extension supports with idle rollers in infeed & outfeed.Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meter on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". -- Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brake on main motor. -- Automatic emergency stop and alarm displayUSA UL or Canada CSA Safety Features

EMC R-evo Z 1350 Sanding & Polishing Center for multi-directional Superfinishing - Award-winning system!Superfinishing obtained by combining electronically controlled, segmented sanding pads with the continuous rotation of the entire sanding head assembly (carousel). This revolutionary system is equally effective as regular wide belt sanders with 4 heads!The carousel rotation is servo-controlled, and can also be operated at standstill in any angular position. The revolving sanding head provides a much more consistent overall finish, and better use of the entire abrasive sanding belt.Motorized doors, sliding and foldaway. Useful working width 1,350 mm (53"). Working thickness min./max. 5 - 180 mm (0.2" - 7"); Constant pass line.Part/Panel Reading unit with Electronic Segments: -- RB-75 Panel reading at infeed, (75) segments with electronic feeler pads. -- Electronic commands activated by magnetic switches. -- Panel detection by large diameter rubber wheels. -- Integrated electronic system.Machine Specifications: -- Hyper finishing abrasive belt 4,960 x 1,430 mm (195.3" x 56-5/16"). -- Chevron belt (inside) length 4,560 mm (179.5"). -- Carousel rotating speed infinitely variable 0.1 - 40 RPM. -- Two electronically controlled segmented sanding pads. Both with 75 segments, each 18 mm wide. -- APC - Automatic Programmable Control and setting of the air pressure for the electronic pads. -- Sanding pads pressure controllable from 0 - 4 bar (0 - 58 PSI). -- Main motor 11 kW (15 HP), Inverter Controlled for infinitely variable abrasive belt speeds 3 - 18 m/Sec (10 - 59 FPS). -- Double oscillating blowers for parts & feed belt cleaning. Activated by part size. -- Motorized linear sliding doors, total stroke 2,100 mm (82.7"). -- Including abrasive belt loading trolley for easy exchange of the sanding belt. -- At outfeed: TAMPICO brush roller for part cleaning, diameter 150 mm (6"), and TAMPICO brush roller for feed belt cleaning, diameter 150 mm (6").Feed System: -- Constant pass line, 900 mm (35-7/16") from floor. -- P.A. Automatic thickness caliper with radio frequency remote control. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Vacuum conveyor bed assembly, fan mounted inside the machine. Inverter controlled 4 kW (5,5 HP) motor. -- Variable feed belt speed, adjustable from 2,5 to 16 m/Min (8 - 52 FPM), Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.Machine Management System: -- Electronic programmable color TSD TOUCH SCREEN DISPLAY, 15,4" wide. -- PLC Power Logic Control for high speed data transmitting. CPU Pentium Intel Atom Z510; 1,1 GHz, DDR2 RAM 512MB expandable. -- Connection 3x USB, 1x RS232, 1x Ethernet 10/100/1000. -- Memory capacity of (200) working programs. -- Operating system Microsoft Windows 7. -- Graphic synoptic to facilitate programming. -- Software and connections prepa

EMC ROTOPLUS 1350 – LUC (1)5 + BRILL 15 Polishing & Buffing LineHeavy Duty Automatic Polishing & Buffing line for high gloss lacquered panels, consisting of: -- Infeed Conveyor -- ROTOPLUS 1350 LUC 5+1 - Polishing and Wax Application machine -- Intermediate Conveyor -- ROTOPLUS 1350 BRILL 15x - Buffing Polishing machine -- Outfeed Conveyor -- Synchronization of feed speed of all equipment in the line, the Rotoplus machines including all conveyorsFollowing are the full specifications: -- Infeed Conveyor, 1.500 x 1.350 mm (59" x 53") Constant pass line 900 mm (35") +/- 40 mm (1-9/16"). Variable feed speed inverter controlled and electronically controlled for synchronized speed and transfer with all other machines of the line.Feed speeds from 0,4 to 8 m/Min (1,3 - 26 FPM). -- ROTOPLUS 1350 LUC 5+1Polishing and Wax application machine for high gloss lacquered wood panels for Polyurethane lacquer or brilliant straight, brushes adjustable at different angles. Equipped with (1) longitudinal Brush Head plus (5) rotating brushes on carousel.1st STATION - Longitudinal Polishing Brush:Cleaning polishing cotton brush diameter 275 mm (10-13/16").Length of the brush 1,420 mm (55-5/16").Brush inclined 3° in respect to the parallel 180°.Automatic low pressure Spraying Gun.Longitudinal chain rail system for gun movement.Electric adjustment of the working pressure, operated from main touch screen control unit.Main motor power 7,5 kW (10 HP).Rotating speed adjustable from 260 to 960 RPM by means of inverter 7,5 kW (10 HP). 2nd STATION - Polishing Carousel: CAROUSEL with (5) Brushes.Max. Brush diameter: 350 mm (13-3/4").Spindle diameter 80 mm (3-1/8").Spindle length: 400 mm (15-3/4").(5) Independent motors, 5,5 kW (7,5 HP) each, with counter bearing supports.The working angle of the brushes is adjustable.Variable speed adjustable from 3 to 36 RPM by means of electronic inverter, driven by 4 kW (5,5 HP) motor.Clockwise and anti-clockwise direction of rotation.Programmable speed control operated from main electronic touch screen display. (5) Special shafts for brushes support EXTRA in addition to the standard ones.(5) Cotton rags 350 mm (13-3/4") to fit the shafts.Automatic System for Abrasive Wax application:Pressurized tank (50) liters for liquid abrasives, with automatic miscellaneous bottom exit and pressure regulator for gun.Low pressure spraying gun for liquid abrasives.Electronic valve for spray gun control.Infrared high precision photocell to detect the panels and activate the spraying gun.Adjustable support for spraying gun positioning.Software and graphic control, programmable through PLC and touch screen. Software and Plug for Telemetry. Computer remote diagnostics control: Direct computer connection between EMC and customer, for online support. -- Intermediate Conveyor, 1.500 x 1.350 mm (59" x 53"), Constant pass line 900 mm (35") +/- 40 mm (1-9/16"). Variable feed speed inve

EMC FLEXY 1350 2RP Finishing Sander with (2) Sanding Heads, Roller and Segmented Finishing PadUseful working width 1,350 mm (53"). Working thickness min./max. 3 - 180 mm (1/8" - 7-1/16"). Head configuration:1st Head: Roller "R" Belt dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 250 mm (10"). -- Roller rubber hardness 85 Shore. Constant control to any position with accuracy 0.02 mm. -- Electronic motorized roller pressure adjustment "grit-set system". -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (15 HP). Automatic star-delta starter. -- Abrasive belt cutting speed: 18 m/Sec (59 FPS). Oscillating abrasive belt blower for the roller unit.2nd Head: Segmented Finishing Pad "P" Electronic PAD segmented in (50) sections. -- Belt dimensions: 2.620 x 1.370 mm (103" x 54"). -- Width of the segmented element (section): 27.0 mm (1-1/16"). -- Rotation: Against feed (clockwise). -- Timed oscillating abrasive belt blower. -- Motor power: 11 kW (15 HP) with electronic inverter variable abrasive belt speed 3 to 18 m/Sec (9.8 - 59 FPS).Feed system:Constant pass line, 900 mm (35.4") from floor &#9679 Vacuum conveyor bed, 4 kW Vacuum unit for holddown of smaller parts, mounted inside of the machine base. &#9679 Idle table rollers support in infeed and outfeed. &#9679 Rubber covered presser rollers, grooved. &#9679 Variable feed belt speed, adjustable from 3 to 18 m/Min (9.8 - 59 FPM) Inverter Controlled. &#9679 Large diameter screws on machined guides with columns and pistons. &#9679 Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized "grit set" system; control from touch screen for each working group (head).Electronic programmable color TOUCH SCREEN display, 10" wide &#9679 PLC with micro-processor of latest generation, modular and expandable &#9679 Connection USB, RS232, Ethernet 10/100/1000 &#9679 Memory capacity: 100 working programs or more &#9679 Graphic synoptic to facilitate programmingSoftware facilities: -- Automatic motor sequence starting. -- Display report and reset of alarms (self diagnostic) with memory records. -- Command, programming and display for:&#9679 all electronic pad functions&#9679 thickness&#9679 feeding&#9679 all inverters and for selected groups (heads).&#9679 blowers, including compressed air saving function.Centralized Control Cabinet: IP 54 protection against dust & moisture. Analog ammeter on main control cabinet. Table lifting-lowering thickness system electrically controlled. AUTOMATIC Delta - Star starter on abrasive belt motors. Centralized Independent Pneumatic Control Cabinet: IP 54 protection. Pneumatic air filter with automatic water-drain system. Pneumatic adjustment for "Grit set system". Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI) Options Available: Tampico Brush natural fiber brush for cleaning of

EMC UNDERTOP 1300 2+2 - Wide Belt Sanding Line Top + Bottom, both with (2) Sanding Heads; Steel Roller, Rubber covered Roller.This machine is equipped to process cement fibers!Useful working width 1,300 mm (51"). Working thickness min./max. 3 - 160 mm (1/8" - 6-5/16"). Both Bottom + Top units are equipped as follows:1st Head: Steel Roller "R", Belt dimensions: 1,900 x 1,320 mm (74" x 52"). -- Roller diameter:190 mm (7-1/2"), spirally grooved. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for sanding belt grit compensation. -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (30 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 21 m/Sec (69 FPS). -- Air Jet Blower for abrasive belt cleaning.2nd Head: Roller "R", Rubber covered, spirally grooved. Belt dimensions: 1,900 x 1,320 mm (74" x 52"). -- Roller diameter:190 mm (7-1/2"). Shore hardness 85. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for sanding belt grit compensation. -- Rotation: Against feed (clockwise). -- Motor power: 15 kW (20 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 21 m/Sec (69 FPS). -- Air Jet Blower for abrasive belt cleaning. Feed system: -- Constant pass line, 980 mm (38-9/16") from floor. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM), Inverter Controlled, synchronized feed speed between both machines. -- Motorized height adjustment on (4) precision screws. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device. -- Pre-welded machined working table. -- Pneumatic air floating pressure holddown shoes at infeed, in middle position, and in outfeed position. These pressure holddown shoes are chrome hardened for processing of cement fibers!General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each (head) working group. Electronic programmable color TOUCH SCREEN LCD display, 7" wide -- Resolution 640 x 480 pixels. -- PLC with micro-processor of latest generation, modular and expandable. -- Memory capacity: (100) working programs or more. -- Graphic synoptic to facilitate programming. Front protection IP 65 against dust & moisture.Software facilities: -- Automatic motor sequence starting. -- Display report and reset of alarms (self diagnostic) with memory records. -- Command, programming and display for: &#9679 all electronic pad functions. &#9679 thickness. &#9679 feeding. &#9679 all speed control inverters. &#9679 selected groups. &#9679 blowers, including compressed air saving function. Options Included: -- Vacuum beds both on top + bottom, 4 kw (5,5 HP) each. Vacuum unit for holddown of smaller parts, mounted inside o

EMC EXPLORER 1100 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,100 mm (43"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 1,900 mm (75") x (width) 1,120 mm (44"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 142 mm (6") -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- Motor power 11 kW (15 HP). -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 142 mm (6"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. Flexible sanding pad. Quick Change System for removable pad with felt, rubber and graphite. Rotating cutting speed 17 m/Sec (55.8 FPS). --Driven by same main motor.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 190 (1/8" - 7-1/2"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meters on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". --Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brakes on main motor. -- Automatic emergency stop and alarm displayOption: TAMPICO Cleaning Brush, 150 mm (6") diameter. Please add ...$3,400USA UL or Canada CSA Safety Features

EMC PIONEER 2RK Wide Belt Sander, (2) Head: 37" Width capacity. Drum, Combination Head.Head Configuration: 1st Head: -- Rubber covered contact roll 180 mm diameter.2nd Head: -- Combination Head, rubber covered roller with padSpecifications: -- Useful working width: 950 mm (37"). -- Working thickness min/max: 3 - 170 mm. -- Abrasive belts length: 1,900 mm. -- Abrasive belt width: 975 mm. -- (2) Feed speeds: 5 - 10 m/min. -- Electronic digital display for working thickness. -- Abrasive belt oscillation by electronic photocell. -- Main drive motor 15 HP -- Feed drive 2 to 19 Meter/min.

EMC MERCURY 1350 3WRK Abrasive Planer / Wide Belt Sander with (3) Heads; Planer Head, Contact Roller, and Combination Head.Useful working width 1,350 mm (53"). Working thickness min./max. 3 - 170 mm (1/8" - 6-11/16"). The machines uses abrasive belts 2,620 x 1,370 mm (103" x 54") for longer life of the sanding belts.Head configuration:1st Head: Planer Head "W" -- Cutter head knives diameter 140 mm (5-1/2"). -- Shaft for helicoidal position knives with (380) Interchangeable knives with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 20 independent segments. -- Anti kickback protection made of 72 independent elements. -- On-Off pneumatic cylinder for planer. group in working position. -- Working pressure adjustment. -- Motor power: 15 kW (20 HP). -- Automatic Star-delta starter. -- Speed rotation: 32 m/Sec (115 FPS). -- Soft starter for slow starting2nd Head: Steel Roller "R", Belts dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 180 mm (7"), spirally grooved. -- Electronic motorized roller pressure adjustment "Grit-set system". -- On-Off selector switch control for roller. -- Constant control to any position with accuracy 0.02 mm. -- Rotation: Against feed (clockwise). -- Motor power: 11 kW (15 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 18 m/Sec (59 FPS). -- Timing oscillating cleaning abrasive belt blower located at the bottom 3rd Head: COMBINATION Unit "K", Belt dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 140 mm (5-1/2"). -- Roller rubber hardness 45 Shore, Constant control to any position with accuracy 0.02 mm. -- On-Off selector switch control for 3rd roller including pneumatic piston -- Pneumatic Aluminum PAD , lamina 40 mm, On-Off. -- Quick changing system, extractable blade with felt, rubber and graphite. -- Rotation: Against feed (clockwise). -- Motor power: 11 kW (15 HP) with automatic star-delta starter. Abrasive Belt cutting speed:18 m/Sec (59 FPS).Feed system: -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 18 m/Min (9.8 - 58 FPM) Inverter Controlled. -- Automatic feed belt centering device. General Machine Features: -- Large diameter screws on machined guides with columns and pistons. -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each (head) working group. Electronic programmable color TOUCH SCREEN display, 7" wide -- PLC with micro-processor of latest generation, modular and expandable. -- Connection USB, RS232, Ethernet 10/100/1000. -- Memory capacity: 100 working programs or more. -- Graphic synoptic to facilitate programming.Software facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, programming and display for thickn

EMC GIANT 1350 2WR Abrasive Planer with (2) Heads, Planer Head and RollerTop of the line Heavy Duty Abrasive Planer from EMC. The series of GIANT machines are available in many configurations. Abrasive Planer has a helicoidal head with insert tooling.Useful working width 1,350 mm (53"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").Head configuration: 1st Head: Planer Head "W" -- Cutter head knifes diameter 180 mm. -- Shaft for helicoidal position knifes with (512) Interchangeable knifes with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 24 independent segments. -- Anti kickback protection made of 72 independent elements. -- On-Off pneumatic cylinder for planer group in working position. Working pressure adjustment. Motor power 30 kW (40 HP), Star-delta starterSpeed rotation: 35 m/Sec (115 FPS).2nd Head: Roller "R" Belts dimensions: 3,250 x 1,370 mm (128" x 54"). -- Roller diameter: 320 mm (12-5/8"). -- Roller rubber hardness 45 Shore. Constant control to any position with accuracy 0.02 mm. -- On-Off pneumatic piston, controlled from the electrical panel. -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (30 HP) Automatic star-delta starter. Rotating cutting speed: 21 m/Sec (99 FPS). Blower for the roller unit.Feed system: -- Constant pass line, 900 mm (35.4") from floor (In line machine). -- Vacuum bed, 4 kW (5,5 HP) for hold down of smaller parts, mounted inside of the machine base. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 20 m/Min (9.8 - 65.6 FPM). Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each working group.Electronic programmable color TOUCH SCREEN display, 7" widePLC with micro-processor of latest generation, modular and expandableConnection USB, RS232, Ethernet 10/100/1000Memory capacity: 100 working programs or moreGraphic synoptic to facilitate programmingSoftware facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, programming and display for thickness. -- Command, programming and display for feeding. -- Command, programming and display for all inverters. -- Command, programming and display for selected groups. -- Command, programming and display for blowers, including compressed air saving function. -- Display report and reset of alarms (self diagnostic) with memory records.Options Included: -- Vacuum bed, 4 kW (5,5 HP) for hold down of smaller parts, mounted inside of the machine base. -- Rotating blowers for part and feed belt cleaning. -- LED light inside the machine. -- Telemetry for remote computer assistance

EMC GIANT 1350 3WRF Abrasive Planer with (3) Heads, Planer Head, Roller and Superfinishing PadTop of the line Heavy Duty Abrasive Planer from EMC. The series of GIANT machines are available in many configurations. Abrasive Planer has a helicoidal head with insert tooling.Useful working width 1,350 mm (53"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8"). Head configuration:1st Head: Planer Head "W" -- Cutter head knives diameter 180 mm (7-1/16"). -- Shaft for helicoidal position knives with (512) Interchangeable knifes with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 24 independent segments. -- Anti kickback protection made of 72 independent elements. -- On-Off pneumatic cylinder for planer group in working position. Working pressure adjustment. -- Motor power 30 kW (40 HP), Star-delta starter.Speed rotation: 35 m/Sec (115 FPS).2nd Head: Roller "R" Belts dimensions: 3,250 x 1,370 mm (128" x 54"). -- Roller diameter: 250 mm (9-13/16"). -- Roller rubber hardness 60-65 Shore. Constant control to any position with accuracy 0.02 mm. -- On-Off pneumatic piston, controlled from the electrical panel. -- "Grit-set system". -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (30 HP) Automatic star-delta starter. Rotating cutting speed: 21 m/Sec (99 FPS). Blower for the roller unit.3rd Head: SUPERFINISHING PAD "F" Electronic PAD segmented in (75) sections. -- Belts dimensions: 3,250 x 1.370 mm (127-15/16" x 54"). -- Width of a single element (section): 18 mm (11/16"). -- APC - Automatic Programmable Control and setting of the air pressure. -- Electronic motorized roller pressure adjustment "grit-set system". -- Rotation: Against feed (clockwise). -- Timed oscillating abrasive belt "air jets" cleaning. -- Motor power: 18,5 kW (25 HP) with electronic inverter variable abrasive belt speed 3 to 18 m/Sec (9.8 - 59 FPS).Feed system: -- Constant pass line, 900 mm (35.4") from floor (In line machine). -- Vacuum bed, 4 kW (5,5 HP) for hold down of smaller parts, mounted inside of the machine base. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 20 m/Min (9.8 - 65.6 FPM). Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each working group.Electronic programmable color TOUCH SCREEN display, 7" widePLC with micro-processor of latest generation, modular and expandableConnection USB, RS232, Ethernet 10/100/1000Memory capacity: 100 working programs or moreGraphic synoptic to facilitate programmingSoftware facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, program

EMC FLEXY 1350 3WRK Abrasive Planer / Wide Belt Sander with (3) Heads; Knife Head, Roller, Combination Head Roller/Pad.Useful working width 1,350 mm (53"). Working thickness min./max. 3 - 190 mm (1/8" - 7-1/2").Head configuration: 1st Head: Knife Planer Head "W" -- Cutter head knives diameter 140 mm (5-1/2"). -- Shaft for helicoidal position knives with (380) Interchangeable knifes with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 24 independent segments. -- Anti kickback protection made of 70 independent elements. -- On-Off pneumatic cylinder for planer. group in working position. -- Working pressure adjustment. -- Motor power 15 kW (20 HP). -- Automatic Star-delta starter. -- Speed rotation: 35 m/Sec (115 FPS).2nd Head: Steel Roller "R", Belts dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 250 mm (10"), spirally grooved. -- Electronic motorized roller pressure adjustment "Grit-set system". -- Constant control to any position with accuracy 0.02 mm. -- Rotation: Against feed (clockwise). -- Motor power 15 kW (20 HP). -- Automatic star-delta starter. -- Abrasive Belt cutting speed: 18 m/Sec (59 FPS). -- Air Jet Blower for abrasive belt cleaning.3rd Head: Combination Head "K", Belt dimensions: 2,620 x 1,370 mm (103" x 54"). -- 3° roller diameter mm 150, Roller rubber covered, hardness 45 shores, Roller pressure adjustment control and "grit-set system" -- ON-OFF selector switch control for 3° roller, including pneumatic piston -- PNEUMATIC aluminum pad, lamina 40 mm, ON-OFF -- Quick changing system; extractable blade with felt, rubber and graphite -- Abrasive belt motor power 15kW (20hp) • Soft starter for slow starting 15kW• Rotating cutting speed 18 m/sec. -- Air Jet Blower for abrasive belt cleaning.Feed system:Constant pass line, 900 mm (35.4") from floor -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 18 m/Min (9.8 - 59 FPM) Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each (head) working group. Electronic programmable color Touch Screen display, 10" wide -- PLC with micro-processor of latest generation, modular and expandable. -- Connection USB, RS232, Ethernet 10/100/1000. -- Memory capacity: 100 working programs or more. -- Graphic synoptic to facilitate programming.Software facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, programming and display for thickness. -- Command, programming and display for feeding. -- Command, programming and display for all inverters. -- Command, programming and display for selected groups