MTS 15 HP Baghouse Dust Collector w/ Pulse Jet CleaningMTS filter housings are made from heavy-duty steel material. A downward air stream in the pre-separator chamber separates coarse-particles before they reach the filter area. The fine dust is then filtered out to and efficiency of more than 99.9%.Specifications: -- Top mounted 15 HP motor. -- Total number of filter bags - 32. -- 5,700 CFM. -- Pulse jet filter cleaning with blasts of compressed air from the clean air side. -- Control panel(3) units were available and now only (2)! !

MULTISCORE CD-4-30 CABINET GROOVER: -- Specifications:30" Wide x 50" long max. cap., 1" max. material thickness; 30 HP main motor; 3-15/16" dia. arbor @ 3,500 RPM; aluminum bedplate slotted at 1-1/2" spacing for about (20) tool positions; quick release tensioner on the arbor drive belts. -- Equipped with: Feed System: Reciprocating push fence with wood extension fingers to assure consistently square cuts; push fence carries the part through the entire cutting area completely past the arbor. Extension fingers are laterally adjustable for different cut widths. Pneumatic infeed plastic holdover fence laterally adj. to hold parts up against the fence. (8) Hold-down arms with lateral & vertical adjustment mount to a T-slot rack to press parts against the feed table during machining. -- Feed Drive/Speed: 2 HP - 1,750 RPM AC Inverter; variable feed motor via gear motor, with dynamic brake; 0 - 60 FPM. Features: -- Material is pushed off the exit side while machine operator can load new parts at the infeed table. Cutterhead assembly is end supported, adjustable up & down via handwheel, and jam nut tooling locking system. -- NOTE: This machine is currently setup for wainscoting and kitchen cabinet doors.

MULTITEK - TRC 460, ...Rim Crusher: ...Less than (300) Hours!Features & Specifications:• Tough MULTITEK® products; simple and strong. Truck Rim Crusher makes wheel salvage easier. • Powered by: Fuel-efficient 25 HP liquid-cooled diesel engine with operator instrument panel control.• The powerful MULTITEK built 6" (15.2 cm) diameter hydraulic cylinder features a Heavy-Duty aluminum piston for continuous duty cycle application.• Power-assisted hydraulic wheel lift arm means less work to load heavy truck wheels.• Powerful 70,000 Lbs (31,752 kG) of crushing force.• Simple: Minimal training and maintenance required.• Standard 2"; ball hitch.• Dimensions: 80" (203 cm) W x 171" (434 cm) L; weight: 3,400 Lbs (1,542 kG).• Engine: Liquid-cooled Diesel with electric start.• Cycle Time: (35) Seconds.

MURPHY-RODGERS HEC-216-S/10 33,000 CFM Continuous Duty Automatic Self-Cleaning Pulse Jet Baghouse Dust CollectorEquipped with: -- (216) 5" Dia. x 10' L Cloth filter bags. -- (2) 42-1/2" W x 68" H & (2) 40-1/2" x 68" H Top access doors. -- (3) Front & (2) Side 27" W x 54" H Filter access doors. -- (2) Square cone bottom hoppers, each with 25" x 25" Discharge openings. -- System utilizes (2) 4-1/2’ x 6’ x 4’ H Waste containers (Not included). -- CHICAGO 100 HP - 1,780 RPM Roof-Mounted Blower, with 41"; Dia. Inlet. -- Motorized dampers for Winter & Summer modes. -- Winter mode directs air back into building, reducing heat loss. -- Summer mode directs air outside, cooling building, Building door must be open to allow replacement air. -- Electrical controls (As pictured).Complete with: -- Spare Filter Bags.NOTE: Installed Used in 2016 with New 100 HP Motor, New Bearings in Blower, & New Spring Mounts.NOTE: Variable Frequency Drive Needs to be Replaced.

MURPHY-RODGERS MRJ-610-122 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan. -- 8,500 CFM approx. @ 9 to 1 air to cloth ratio baghouse dust collector with (60) 10-feet long filters; total cloth area of 943 sq. ft. -- Filter Cleaning: Continuous Self-cleaning Using Compressed Air. -- Main Fan: 30 HP top mounted blower motor. with approx 18" dia. inlet . --System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, top safety railing, and approx 16" Rotary Air Lock. -- Actual model is MRJ 610 -122.

MURPHY-RODGERS MRSE-14-RAL Baghouse Dust CollectorSpecifications: 14" Inlet dia., 4,836 CFM, (63) bags with 520 sq. ft. filter area, 9.3:1 air-to-cloth ratio, 20 HP fan motor, primary separator built into unit, secondary separation of fine particles by filter bag section, cone shaped bottom empties into (4) 55-gal. drums. -- Equipped with: -- Rotary Air Lock. -- Fully automatic shaker controls with electric shaker as standard; consists of panel box with shaker starter, transformer for 11 5V circuitry, solid-state timer for fan deceleration & shaking cycle. -- All necessary relays and internal wiring inside the panel box.

VECOPLAN VAZ 120/105 Low noise Wood Waste GrinderSpecifications: -- Vertical 2.9 cubic yard hopper, 42" X 48" opening, 30 HP rotor motor. -- 10" Dia. rotor with (27) indexable, replaceable cutter knives, rotor/cutterhead grinds at 120 RPM. -- Hydraulic pusher ram; separate electrical control panel with pushbutton controls, 80 DBA noise level. -- Features: -- 4-Sided flared hopper, Fluid TurboCoupling. -- Easy access Screen, Suitable for Wood, Plastic or Paper applications.

VESTIL EHLT-2464-2-55 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 2,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 24" x 64". -- Lowered height 7", raised height 55". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VESTIL EHLT-4896-4-56 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 4,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 48" x 96". -- Lowered height 8", raised height 56". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VICKERS 60 HP Hydraulic Power PackHere's a Hydraulic Power Pack with all the bells and whistles. VICKERS pump and valves and a SENTINEL tank. Hydraulic Power Pack Includes: -- Variable volume, pressure compensated, piston pump. -- Capacity - 8 cu. in. / rev. -- Pressure rating - 4,000 psi. -- Driver - 60 HP Electric motor 1,750 RPM. -- Reservoir - 200 gal. -- Kidney loop - Gear pump w/ filter. -- Air-cooled heat exchanger. -- Return line filter. -- Liquid lever switch and temperature switch. -- Fluid inspection window.NOTE: This item was installed earlier but never used. The year of manufacturing is approximate.

WADKIN - NV 300, ...Profile GrinderSpecifications: --Working dimensions: 12-3/8" Max. arbor capacity. --Cutting circle 13-3/4" max. and 2-3/4" min. dia. --Grinding motor: 2 HP Motor, 3,600 RPM grinding wheel speed. -- 1-1/2" Max. profile depth. -- 9" Max. grinding wheel diameter.Equipped with & Features: --: 0.02 HP Coolant system pump motor. -- 8-Gal. removable coolant tank with block magnet. --Top & Bottom coolant flow control. -- Infinitely variable head tilt mechanism 0° - 15° max. -- Linear action carriage. --Clearance angle scale. -- Adjustable arm rest and twin coolant pipes to profile wheel.

16' x 10" Wide Vibrating Conveyor with 10" wide pan; 1/2" stroke at 585 RPM, feeds at approx. 25 FPM.

WEIMA C 150 Briquette PressSpecifications & Features: -- Produces 2" (50 mm) dia. Briquettes; -- Hopper opening of 41" x 41" (1,040 x 1,040 mm); hopper volume 1.43 cu/yd (1.1 cbm). Equipped with: -- 9 HP Hydraulic motor; 0.75 HP auger motor; hydraulic oil volume of 26.4 gallons (100 liters). -- Vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material; extrusion chamber is continually filled via rotary screw type auger. -- Volume reduction from chip/dust to block up to 10:1 ratio at 2,600 PSI; hourly output up to 80 - 120 Lbs/Hr ("quoted output is an average and can be influenced by density, material size, screen size, feeding form, and other factors").Features: -- Briquette length control, chrome plated clamp, oil level switch, control panel side-mounted to hopper, and overheating protection for hydraulic oil. Solid German engineering. - Freight, start-up, discharge pipes, etc. not included.

WEIMA Horizontal Beaver 300 Slow Speed, High Torque Waste Grinder w/Vibratory Conveyor. 25 HP (18.5 kW), 10" rotor diameter, 11.8" (300 mm) rotor length, (14) 40 x 40 mm indexable, concave cutters; 11.8" x 4" infeed opening. Equipped with: -- WRRL 300 12' Vibratory Conveyor (550 Lbs). -- The "Horizontal Beaver" receives the material from a vibratory conveyor system; from the conveyor, a feed roller system pinches and feeds the material into the rotor. -- Features: Patented "V-Rotor" design utilizes a V-groove rotor closely matched to grooves in the counter-knife; the V-Rotor produces uniform discharged material that is free of splinters and dedicates more horsepower to grinding. -- Includes integrated "plug-and-play" electrical control system with UL approved components; -- Extraction requirements: 1,900 CFM (28 MPS), 8" (200 mm) diameter for dust collection. Total Approx. weight of 2,430 Lbs.

WEIMA TH 1500 M Briquette Press (Square Brick) -- Specifications: Produces 5.9" x 2.3" (150 x 60 mm) rectangular briquette; hopper opening of 55" x 55" (1,400 x 1,400 mm); hopper volume of 2.46 cu/yd (1.88 cbm). -- Equipped with: 40 HP Hydraulic motor; 2.6 HP auger motor; 3.0 HP agitator motor; hydraulic oil volume of 264 gallons (1,000 liters). -- Volume reduction from chip/dust to block up at a 10:1 ratio; hourly output up to 800 - 900 Lbs. -- Features: Conical shaped agitator with curved hopper corners, "Bridge Breaker" mounted on agitator; automatic "On/Off" integrated in feeding hopper; hydraulic oil cooling, overheating protection for hydraulic oil. -- Complete with: Touch-Screen control panel on swivel mount; discharge ramp for briquette extraction, chrome plated clamp, and an oil level switch. -- Solid German engineering.

WEIMA TH 514 Briquette Press (Cylindrical). Produces 2" (50 mm) dia. x 4" (100 mm) long compacted logs. -- Specifications: -- Approx. 1.4 m³ vertical hopper, 12 HP (9 kW) motor; vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material, extrusion chamber is continually filled via rotary screw type auger. -- Approx. hourly output between 80 - 120 Lbs/Hr. ("quoted output is an average and can be influenced by density, material size, screen size, feeding form, and other factors"). -- Equipped with: -- Centralized control panel for easy operation, PLC Logic control & solid German engineering. -- Complete with: -- Auto on/off switch, auto length adjustment, & oil level sensor. -- Optional: -- Hydraulic oil heater, hydraulic oil cooler, transfer piping and customization to customer material handling.

WEIMA - TH 614 HD, ...Metal Briquette Press w/WEIMAI ...4-Shaft Shredder & ConveyorProduces 60 mm dia. x 4" (100 mm) long compacted logs; approx. 1 cbm square vertical hopper.Specifications: -- 18 HP Motor; vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material; extrusion chamber is continually filled via rotary screw type auger. -- Volume reduction from chip/dust to block up to 10:1 approx. ratio. -- Centralized control panel for easy operation: Auger, oil cooler, auto. on/off switch, oil level sensor, and auto length adjuster. -- Includes: -- Metal package for TH 614 HD; catch pan with level switch; fluid pump with 10' of hose; tool steel pressing rod, wear sleeves & clamp; discharge pipe for conveying 60 mm dia. briquettes (3 sections: 1 x 45°; 1 x 90° & 1 x straight). WEIMA - ZMK 30, ...4-Shaft Shredder 4-Shaft Shredder with electrical cabinet & controls.Specifications: -- Dual drive motors: (2) 11 kW (15 HP) Drive motors; hopper opening measures 39.4" x 55.1" (1,000 x 1,400 mm); cutting chamber opening of 18.2" x 27.6" (462 x 700 mm); rotor length of 18.2" (462 mm); rotor speed 25 RPM; cutting disc 11" (280 mm) diameter.JORGENSEN - Transfer Conveyor18" Wide steel belt; collection hopper for under ZMK 30; coolant pump and float switch for fluid transfer.

WEIMA TH 714 Briquette Press (Cylindrical). -- Produces 2-3/4" (70 mm) dia. x 4" (100 mm) long compacted logs. -- Specifications: Approx. 1.4 m³ vertical hopper, 18 HP (13.5 kW) motor; vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material, extrusion chamber is continually filled via rotary screw type auger. -- Approx. hourly output between 240 - 280 Lbs/Hr ("quoted output is an average and can be influenced by density, material size, screen size, feeding form, and other factors"). -- Equipped with: Centralized control panel for easy operation, MITSUBISHI Logic control & solid German engineering. -- Complete with: Auto on/off switch, auto length adjustment, & oil level sensor. -- Optional:: Hydraulic oil heater, hydraulic oil cooler, transfer piping and customization to customer material handling.

WEIMA TH 814 Briquetter A volume reduction of 90% is possible through the briquetting of wood, paper, aluminum and biomass or synthetics, providing significant savings in labor, disposal and storage costs.Material is hand fed or by dust system into the hopper, where an agitator pulls it into the auger and pressing chamber. Specifications: -- Produces 80 mm (approx. 3.1") dia. compacted logs; approx. 2.4 cu. yd. (55.1 x 55.1 x 37") square vertical hopper, 18 HP motor. -- Hydraulic ram compacts the material in the extrusion chamber to produce uniform material, extrusion chamber is continually filled via rotary screw type auger. -- Volume reduction from chip/dust to block up to 10:1 ratio; approx. hourly output between 300 - 400 Lbs/Hr.Features: -- Auto on/off integrated into feeding hopper; automatic briquette length adjustment; conical-shaped agitator; dust connection at pressing unit.Options: -- Hydraulic cooling for 24-hour operation, heating for cold weather start-ups; plastic tubing discharge into Gaylord or carousel bagging system. .

WEIMA TIGER 400 Horizontal Slow Speed Single Shaft Wood Grinder w/Vibratory ConveyorSpecifications: -- 6" High (160 mm) x 15-11/16" (400 mm) wide max. infeed opening, 50 HP rotor motor, 14" dia. rotor grinds at 620 RPM (fixed rotor speed depending on application). -- Equipped with: -- Patented "V-ROTOR" design utilizes a v-groove rotor closely matched to grooves in the counter-knife to ensure uniform discharge free of splinters, reduce friction, and dedicate more horsepower to grinding. -- Features: -- (22) Replaceable back bolt-on cutter knives (welded knife holders standard, bolt-ons per customer request), recessed concave cutters with low clearance over the rotor extend cutter life, protect the bolts, and reduce machine wear. -- Infeed roller with replaceable wear strips for ease of maintenance, feed speed is controlled by monitoring the amp draw of the rotor, preventing "braking" or excessive pressure on the rotor, the vibratory infeed conveyor (12'), is also tied into the feed roll to eliminate binding. -- 9.85" (250 mm) Dia. dust collection outlet (3,000 CFM required). -- Includes: -- Heavy Duty low-profile frame (15-3/4" passline height); integrated "plug-and-play" electrical control system with UL approved components (system UL certification available upon request for additional charge); up to 16' vibratory infeed conveyor available.