SCM SANDYA - 40 M3 135, ...3-Head Wide Belt Sander 52" Width cap. Drum, Drum, Combination HeadHead Configuration:1st Head: Steel Contact 22 kW Pneumatic blowdown and alignment.2nd Head : Rubber Contact 18.5 kW Pneumatic blowdown and alignment.3rd Head: Combination Platen 15 kW Pneumatic blowdown and alignment.Note:The SCM sander does not have a brush. After the 3rd head, it has this pneumatic blow-off bar with multiple blow-offs running the length of the sanders width. Sander can be seen under power if needed.Specifications: -- 53" x 103" Abrasive belts with electronic tracking. -- All heads with abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 5 HP motor. -- Automatic part thickness adjustment. -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout. --0" - 7-7/8" opening. -- Equipped with & Features -- Outfeed rubber covered holddown rolls or shoes on all heads. -- Motor load meters. --Infeed and outfeed conveyor extensions. -- WYE-DELTA soft start.Note: The SANDYA model "40" is more or less the same as the SANDYA "30" but more Heavy Duty.

SCM UNO CS Wide Belt Sander37" Wide cap., 1-Head machine;Specifications: -- Combination head with 4" dia. 85 shore grooved rubber contact drum and 2" wide finishing platen; -- 18 HP motor; 37" x 60" abrasive belt size; 0.87 HP 2-speed feed - 15 & 30 FPM. -- Powered raise and lower w/ LED digital readout; 6-1/4" max. thickness cap., 12-1/2 min. material length. -- Includes: 5-1/2" dia. dust outlet, infeed, and outfeed hold-down roller and load meter.

SCM DMC TC 1350 RKP Wide Belt Sander ( 3 ) HeadsWidth cap. 53" , Drum, Combination Head, PlatenHead Configuration1st Head: 35 hp 9″ Spiral Drum2nd Head: 24 hp/30 hp dual RPM 7″ Spiral Drum/Combination Head W/Segmented Platen,3rd Head: 15 hp VFD driven multi speed Segmented Platen4th Station: Panel CleanerSpecifications -- 53″ working width, 656 hours of operation, --. Yes, it has (2) segmented platens. It’s from a custom shop and was utilized for very specific custom work and nothing else. -- 6.5″ thickness capacityEquipped with & Features -- Auto thickness calibration, -- Vacuum bed, -- 5 hp vfd controlled feed speed, and multiple modes. -- There is also a manual and (4) spare platens.Note: Only issue found , are lines on the LCD Screen (see pictures).

SCM SANDYA 3-RCS-95 Wide Belt Sander 9 ( 2 ) Heads36" width cap. Drum, PlatenHead Configuration1st Head : Contact Drum2nd Head : Combination HeadSpecifications: -- 1st Head: Contact roll, 4-3/4" dia.; -- 2nd Head: Combination head, with rubber covered contact roll, 4-3/4" and 2" wide finishing platen -- Both contact rolls & platen with cam height adjustments. -- 30 HP Motor driving both heads;Equipped with & Features -- 37" x 75" abrasive belts -- Electronic tracking and pneumatic belt tensioning. -- Infeed & outfeed rolls, -- Dual feed speed of 15 & 30 FPM, -- 0.5 HP feed drive -- Automatic part thickness adjustment -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout, -- 0" - 6-1/4" opening. -- Motor load meters, -- Infeed & outfeed conveyor roller extensions, (2) 5" dust ports.

SCM Sandya 7 S Wide Belt Sander (2) Heads43" Width cap, Drum, Combination HeadHead Configuration1st Head: Contact roll, 6-1/4" dia., 25 HP motor; 2nd Head: Combination head, rubber-covered contact roll, 6-1/4" dia., and 2" wide finishing platen, 18 HP motor.Specifications: -- Great solid wood finish Sander. ÷ 43" x 75" or 85" Abrasive belts with electronic tracking & pneumatic belt tensioning. -- Conveyor belt feed with variable feed speed, 10 - 60 FPM, 3 HP motor, -- Automatic part thickness adjustment, motorized thickness opening with LED readout, -- 0" - 6-1/4" via (4) precision conveyor bed jacks.Equipped with & Feature: -- Infeed & outfeed spring loaded rubber covered holddown rolls on all heads, -- Motor load meters -- Infeed and outfeed conveyor extensions.

SCM Sandy 10 -RCS-110 Wide Belt Sander (2) Heads43" Width cap. Drum, Combination HeadHead Configuration:1st. Head: 7" diameter corrugated metal roller for calibration 35 HP ( Drives both Heads )2nd Head: Combination head with 7" dia. contact roller (spiral grooved rubber covered); air/jump finishing platen controlled with timers to eliminate any rounding on leading & trailing edges of the panel, 2" wide platen.Specifications --103" long x 43" wide Abrasive belts --Air tracking, floating & rigid bed for sanding of veneers & solid panels; infeed & outfeed spring loaded holddown rolls -- Minimum workpiece length 16" --Thickness capacity 6.25". --Separate 2.5 H.P. variable speed feed motor delivering feed speeds from 15 to 70 FPMNote: The seller has 20 boxes of various sandpaper belts (80 – 150 grit) that will be included.

SHENG-SHING - SDM-15 ...Wide Belt Sander (Open Ended)15" Single Head Wide Belt Sander with open end for up to 30 " capacity. -- Sanding Head: 15" Wide (30" cap. with 2-pass); 8" Helically Grooved Rubber Covered Contact Roll with 7.5 HP Drive. -- Features: 0" - 6" Part thickness cap., 2-speed conveyor feed 12 or 16 FPM; 16" x 48" Abrasive belts with air tensioning, pneumatic abrasive belt tracking.

SHENG-SHING SDM-25 25" WIDE BELT SANDER1-Head, 24" width cap., rubber covered contact roll, approx. 10 HP motor. -- Abrasive belt size 25" x 48", with air tensioning and electronic abrasive belt tracking. -- 5-1/2" Max. height opening with manual raise & lower; variable feed speed drive. -- Complete with: Magnetic controls & dust outlet.

STATE MODEL B-4 OSCILLATING SPINDLE SANDERSpecifications -- Tilting table design with pedestal floor mount --Table size.20" X 24" -- Table height 40" -- Table tilt 15° up, 45° down -- Spindle speed 1725 RPM -- Vertical oscillation 1-5/8" -- Oscillations/min.90 -- Lubrication...........Oil bath splash -- ÷ ÷Heavy duty 1/2 HP motor Maintenance free 1725 rpm TENV totally enclosed non-vented motor, rated for continuous operation, assuring long term dependable service. -- Safe operator controls Magnetic motor starter with overload protection for save installation. All controls are mounted for operator convenience. -- Operator friendly hand-wheel-tilting Engineered worm gear design allows table to be tilted 15 degrees up and 45 degrees down relative to spindle. Easy-to-read scale allows for accurate tilt determination before engaging locking device. A tapered pin locks the table during horizontal sanding operations. -- Safety features Magnetic motor starter with overload protection, safety labels, well-placed ergonomic controls, 3 throat rings to minimize table-to-spindle clearance, POSITIV-LOK spindles provide safe and quick means of changing spindles. -- Recently Cleaned, checked, electrical contacts cleaned, machine partially disassembled cleaned, re-assembled and tightened, and oil sight glass replacedWeight: 280 lbs.

STATE B-4 OSCILLATING SPINDLE SANDER 1.5 HP Motor with manual switch, (9) spindles from 1/4" DIA to 4" DIA., 1,725 RPM spindle rotation, 20" x 24" table tilts 15° up and 45° down, table height 40". Also includes work light

STEINEMANN OSUS NOVA 160/6 K-FS/NS-OPTIMAT Top and Bottom Calibrating Sander(6) heads consisting in 2 machines, first machine top/bottom opposed head. Secoind machine (4) head with Combi and finishing platenFeatured: -- 2-Head K, (1) top & (1) bottom; both heads directly opposed. for calibrating -- (4) head FS/NS top/bottom first Combi head, second finishing platenSpecifications:First machine Calibrating Sander: -- Top/bottom opposed single head -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on K head 34 M/sec. (6,667 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- 100 HP motor each head. -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine only Second Machine Finishing Sander: -- Top/bottom (2) head each as Combination drum/platen and finishing platen -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on FS head 22 M/sec. (4,330 SFM) -- Cutting speed on NS head 22M/sec. (4,330 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- No motor installed -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine Not included: -- infeed and outfeed conveyor -- Conveyor between the machine -- “all the control wiring goes into a cabinet that is separate on each machine. That is just the wiring for the sensors and solenoids for braking and belt tracking stuff. There are no motor controls with these so there are no starters included. The 2 head comes with (2) 150 HP motors and the 4 head has no motors on it. In order to make these operational you would need a PLC and HMI to run the controls and motor starters and would need to buy motor controls

STEINEMANN Type OSUS NOVA-RSA-190K Sanding Line;Complete with the following major components and features: -- (4) Sets of top & bottom opposed heads (8 heads total). -- Final head is equipped with Platen Sanding (smoothing bars). -- ISS thickness sensor system. -- 1900mm (74 inches) Max. Working Width (sander only, grade line width is a nominal 5 feet). -- CONVEY-KEYSTONE Vacuum Panel Feeder. -- CONVEY-KEYSTONE Canted Roll Infeed Section. -- CONVEY-KEYSTONE Canted Roll Outfeed Section. -- CONVEY-KEYSTONE panel grading system with (3) sort bins; automatic bin selection & discharge. -- STEINEMANN sander controls and control cabinets associated with the sander system. -- (3) Sections of ALLEN-BRADLEY Series 2100 Motor Control Centers (MCCs). (One small section to remain behind for further plant use.)NOTES: &#9679 This is a sanding line designed for manufacturing MDF or Particle Board. Thus, it is built for large capacity. &#9679 Still in place. &#9679 Last in service about 1½ years ago (2021).