SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location, refurbished added installation.

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

TORIT 360-IRD-15 Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Down flow air pattern allows airflow and gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure dropSpecifications: -- 15 HP direct drive, floor mounted blower. -- 4,800 CFM @ 8" wg, 4,050 CFM @ 9" wg, 2,400 CFM @ 10" wg -- (21) Dura-life filter bags with a cloth area of 192 sq. ft. -- (3) Collection points for plastic collection bags.

TORIT - 460-IRD-20: Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Downflow air pattern allows airflow & gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure drop.Specifications -- 20 HP Direct drive; floor mounted blower. -- Fan inlet: 17". -- CFM: 7,000. -- Set of filter bags. -- Steel elbow from fan to collector. Motor Starter included.

TORIT-DONALDSON ADMC AD8 DRYFLO Cartridge Dust Collector. A Mist collector designed for long-lasting high collection efficiency capture of coolant and machining oil mists in metalworking applications. Even smaller amounts of dust can be filtered in the dirty air stream. -- DRYFLO is a proprietary cartridge which outperforms electrostatic precipitators and mist collectors utilizing standard HVAC envelope and cassette filters. Filter unit features a unique air-side filter retention system allowing for quick filter changes with minimal worker contact with collected oil. -- Also feature three-stage Filtration via a.) prefilter, b.) wrap allowing, c.) the filter cartridge to drain and coalesce smaller coolant mist droplets in to larger droplets. Plus optional fourth stage HEPA filters available for applications where smoke exists or additional efficiency of discharge air is required. -- Overall data: Capable of 17,600 CFM; (8) Filter Cartridges, 1,760 sq. ft. of filter area, -- Complete with: Ground mounted fan powered by a 40 HP motor, belt-driven. Fan includes a variable volume inlet. In prior application clean air was not retruned to building. -- Blower currently setup for approx. 15,000 CFM with 40 HP, Baldor Super-E, 324T frame, 1.780 RPM motor. -- Enclosure dimensions: 133" long, 68" deep, 160" high. Filter weight is 7,300 lbs.

DONALDSON TORIT 232 RF-8 24,000 CFM Baghouse Dust Collector (Refurbished 2017), with Rotary Air Lock & AIRCOM 32" Dia. Explosion Isolation Flap Valve (New 2017) -- Specifications: Approx. 10-1/2' Dia. x 24' H Baghouse with 7-1/2' H Cone bottom & (232) 8' L Cloth filter bags totaling about 2,414 Sq. Ft. of Cloth area. The Air-to-Cloth ratio is 9.94:1. Overall system footprint 25' x 25'. -- AIRCOM SNR 800 32" Dia. SNR (Safety Not Return) Explosion Isolation Flap Valve, S/N 0977003 (2017), Certified ATEX EN 15089, Class 2, NFPA Compliant, with Max. air speed 30m/s, Max. dust concentration: 4 LEL, Kst max. 299 bar m/s, Pred max. 0.25 bar, Pmax. 9 bar, Pipe structure to withstand pressure: 0.25 bar, Explosion resistance of flap 850 mbar, Min. ignition energy 3 - 10 mJ, Min. ignition temperature 420° C (788° F), Temperature range –20° C to +60° C (-4° f to 140° F), Range of applicable volumes 10 - 60 cu. meters (33 - 196 cu. ft.), Anti-opening locks on both flaps. -- 75 HP 1,780 RPM TEFC Motor Driving Blower, Rated at 24,000 CFM @12" SP, with 36" Dia. Inlet & 30" x 36" Outlet. -- KOGER SIZE 12 Rotary Air Lock, with 12" Dia. Inlet & Outlet, 1 HP Motor. -- MURPHY-RODGERS MRT-12 10 HP Blower, S/N 1272, with 12" Dia. Inlet & 8" x 11" Outlet. -- ROOTS 32 U-RAI 5 HP Lobe Blower, S/N 0802963165. -- Electrical controls included. -- Actual model is "232FRW8" (Walk-in unit), Estimated shipping weight 15,500 lbs.

UAS -BHT (CALCOR) MIB-11-T19- SVA Pulse Jet baghouse dust collector. MIB is Modular Industrial Baghouse. -- Has qty (18) each of filter cartridge # 04007500 (6.125 x 75") and qty (18) each of filter cartridge # 0400000249 (6.125 x 41.6250"), for a total 1,896 sq. ft with pleated Spunbonded Polyester w/PPTFE filter bags. -- OEM rated for 5,000 ACFM @ 11" SP, resulting in a 2.64 Air-to-cloth ratio. -- 20 HP Siemens motor, on a large floor-mounted blower -- Comes with DPC and Timer board for Pulse Cleaning Control. Allen Brady Starter and air quality motoring. -- Discharges thru Pyramid hopper into a 55 Gallon Drum. Includes dome style explosion vent.. -- Housing dimensions: 60" x 60" x 232" high. Total weight with filters: 3800 Lbs. -- Looks like its brand new. -- Last used for a CNC Laser Cutter.

UNKNOWN 210-120-6 Pulse Jet Dust Collector with Rotary Air Lock. -- Filter Specs: 3,300 sq. ft of bag area made up of (210) bags, 10' long, 6" dia. At an air to cloth ratio of 5:1 can produce about 16,500 CFM. -- 60 HP (45 KW) TEFC, 1760 RPM Motor driving a VTC 900 TGE VENTILLATION Centrifugal Van, belt-driven with Variable Volume Damper on Inlet -- Fan Specs: 15,500 CFM @ 12" total SP, 1760 RPM, motor load 28.43 KW (38.1 BHP). -- Filter cleaning: Via plant compressed air supplied to pulse jet cleaning manifold. Top access to filter bag maintenance. -- Includes: Rectangular construction supported by a steel with approx 10' by 12' stand. Access ladder top service platform and perimeter railing. -- Top access filters -- Comes with Rotary Air Lock connected to a bottom discharge. -- Overall dimensions 10.5' x 12'-4" by about 34 ' high to top of railing.

WESTERN PNEUMATICS WP12 Rotary Air LockSpecifications: -- Discharge opening: "10 x 16" -- Gear motor drive: DODGE 5 HPFeatures: -- Flange mount for installation.

AAF PULSE-PAK 21-3H Pulse-Jet Cartridge Dust Collector. (3H) is three-high filter elements. (21) is the total number of Panel Pak V's.The Panel Pak filter element has two flat panels of pleated media in a Vee-Configuration allowing installation and change-out with minimum time and effort. Each cartridge has its own gasket ensuring a positive, air tight seal. -- Consists of two modules: one containing (9) 3x3 filters and the second contains (12) 4x3 filter cartridges, for a total of (21) cartridges. -- Housing dimensions: 191.75" High (with 48" hopper clearance), 104.25" Wide, 94.25" Depth, and Weighs about 6,400 Lbs. -- Air consumption about 6 cubic feet/hr. at 90 PSI of clean dried air. -- Fan and Airlock available at extra cost. please inquire.

ACT 3-12 Cartridge Dust Collector Cartridge style downflow dust collector rated at 4,000 CFM @ 13". Heavy-duty with 7 and 10 gauge construction. Specifications: -- Blower, 15 HP rated at 4,000 CFM. @ 13" -- (12) Poly-Elite, spun-bond polyester media with 100 Sq. Ft. of media per filter filter (total 1,200 Sq. Ft.) that are 99.9% efficient. -- Reverse pulse filter cleaning system. -- 15HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3ph -- DK-XP – explosion rated drum kit with quick-lock easy-access filter doors. -- 16" inletEquipped with: -- TCBI 15 HP Blower with direct drive, top mount. -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (6) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Return Air Includes: -- Shut off landing spot in control panel for explosion isolation valve. -- Explosion Vent installed with hardware, 24" x 36" explosion relief panel. 5.72 sq ft vent area. Domed for durability. KST value required. -- Sprinkler coupler for collectors with 1 module. -- Solenoid heater kit with 1 heat trace kit for cold weather installation. -- 14" VF - Explosion Isolation Valve Assembly (dirty air to dust collector), Must be installed between 14' and 55' from the dust collector inlet. If an elbow exists, minimum distance is 21'. -- Custom - Explosion Isolation Valve, 16" VF - Explosion Isolation Valve Assembly (clean air return to building). Must be installed between 24' and 55' from the dust collector outlet. -- 10 year workmanship and materials warranty -- Made in the USA?Photo does not represent the actual model

ACT 4-16 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 8,000 CFM. Specifications: -- 20 HP Direct drive, top mounter blower rated at 8,000 CFM @ 10" w.c. -- (16) Nano Elite, flame-retardant, Nano-Fiber merv 15, cartridge filters with up to 4,064 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter.Equipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (8) pulse valves. Goyen diaphragm and solenoid valves -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Options: -- Fan outlet damper. -- Fan outlet silencer. Other models available, please check with the Product Manager10 year workmanship and materials warranty -- Made in the USA

ACT 3-6 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 4,000 CFM. Specifications: -- Blower, 10 HP rated at 4,000 CFM @ 10" w.c. -- Holds (6) Nano Elite, merv 15, cartridge filters with up to 1,524 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter panel. -- (6) Filter Upgrade to ACT Nano-Elite, flame-retardant, Nano-Fiber media with industry best Merv 15 efficiencyEquipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (3) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. -- 12" in-let. -- Silencer for TCBI 1010 year manufactures materials and craftsmanship warranty . Made in the USA

ACT 3-24 Cartridge Dust CollectorCartridge style downflow dust collector rated at 8,000 CFM. Heavy-duty with 7 and 10 gauge construction. Specifications: -- Blower, 25 HP rated at 8,000 CFM @ 12" -- (24) Poly-Elite, spun-bond polyester media with 100 Sq. Ft. of media per filter filter (total 2,400 Sq. Ft.) that are 99.9% efficient. -- Reverse pulse filter cleaning system. -- 25HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3ph -- DK-XP – explosion rated drum kit with quick-lock easy-access filter doors. -- 18" inletEquipped with: -- TCBI 25 HP Blower with direct drive, top mount. -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (12) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Return Air Includes: -- Shut off landing spot in control panel for explosion isolation valve. -- Explosion Vent installed with hardware, 36" x 36" explosion relief panel. 8.63 Sq. Ft. vent area. Domed for durability. KST value required. -- Sprinkler coupler for collectors with 1 module. -- Solenoid heater kit with (2) heat trace kits for cold weather installation. -- 18" VF - Explosion Isolation Valve Assembly (dirty air to dust collector), Must be installed between 16' and 55' from the dust collector inlet. If an elbow exists, minimum distance is 24'. -- Custom - Explosion Isolation Valve, 20" VF - Explosion Isolation Valve Assembly (clean air return to building). Must be installed between 19' and 55' from the dust collector outlet. -- 10 year workmanship and materials warranty -- Made in the USAPhoto does not represent the actual model

AGET 20SN5157 Cyclone with FT-40 Baghouse2,300 CFM at 9.3" SP; 5 HP Top-mounted blower motor cyclone, 8" inlet dia.,10" outlet diameter. -- Dust particles are pulled through the cyclone with larger particles dropping through the cyclone to dump into collection bin. Finer particles are forced through the Baghouse to filter the remaining air.. -- Includes; 5 HP LEESON ELECTRIC TEFC top-mounted blower, cyclone, AGET "FT-40" Baghouse after-filter, manual slide gate opening and automatic bag shaker which comes on after shut down of collector. -- Interior bag house with (40) 5" dia. x 8' L cloth tubes, total filter area of 383 sq. ft. The larger dust particles are pulled through cyclone into (2) 55-Gal barrel storage with manual slide gate opening at bottom.

AIR CURE 484RF10 Dust Collection System with Rotary Air Lock and Abort Gate.Specifications: -- Filter area capacity 56,000 CFM @ 9:1 Air to Cloth Ratio (ACR), approx. 13'- 2" dia. round baghouse; -- (484) Cloth filter bags of 10' length (3" x 6") oval bags provide for radial movement of bag during cleaning for longer life), 6,180 sq. ft. of filter area. -- Designed for filtration media cleaning via 7.5 HP approx.on board rotary air pump for compressed air operating at about 7.5 PSI. Return air outlet and approx. 48" x 48" inlet for dust laden air. -- Rotating cleaning air manifold driven by 1 HP motor, (1) NEMA IV timer & solenoid/diaphragm valve control pulse jets of air to clean each row of bags; galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed. Includes: -- Supplied Fan: ALLIED BLOWER & SHT MTL. SIize: 90 MH fan, 38" inlet dia, with paddle wheel blades powered by 250 HP TEFC motor, ground mounted . Note1: This fan is very versatile as it can operate from 10,000 CFM @ 6" or 7" of water SP all the way up to 40,000 CFM @ approc. 14" of water SP depending on RPM chosen. To be conservative one would keep the upper end to around 1,000 RPM. Motor could be 25 HP or 250 HP at these extremes. Being a radial blade fan it is capable of handling most materials. -- Note 2: Depending on application there is filter area capacity to add another Fan/motor for about 16,000 CFM (as per above). -- Explosion doors; walk-in access door on platform at access door. approx. 18" Rotary Air Lock (RAL) and about 38" Abort Gate with separate support stand and access platform.Features: -- 10-Gauge shell all-welded construction, Tangential scroll inlet and Inlet deflector baffle. -- All cages are unbolted to minimize damage and left in the shell. Bags are removed (to reduce weight on cages) and crated - will likely need to be laundered. -- Actual AIR CURE model is 484AC10. -- Note: Upon installation buyer is responsible for compliance to all applicable NFPA or local, state or Federal codes.Transportation also available at extra cost.

AIR CURE 484RF8 Pulse Jet dust Collector.. -- Overall Specs: 30,00 CFM @ 6.1:1 Air-to-cloth ratio, 158" dia. round baghouse with a capacity of (484) cloth filter bags (Bags not Included) of 8' length (3" x 6" oval bags provide for radial movement of bag during cleaning for longer life), 4,900 sq. ft. of filter. -- Designed for filtration media cleaning via 7.5 HP on board rotary air pump for compressed air operating at about 7.5 psi. Return air outlet and approx. 48" x 48" inlet for dust laden air. -- Filter cleaning: Rotating cleaning air manifold driven by 0.33 HP motor, (1) NEMA 9 solenoid and diaphragm valve control pulse jets of air to clean each row of bags; galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed. -- Includes: AEROVENT (TWIN CITY) model 330, type CBA-SW Class 4 Backward Inclined Air Handling Blower, Arrangement 9 with 100 HP TEFC motor; Explosion doors; walk-in access door on platform at top and safety ladder. -- Original cages will be removed and stored separately from the filter. Unique skirt at bottom of cyclone thus no support steel is needed and facilitates anchor bolt installation. -- Depending on application/desired air capacity it can be increased to about 44,000 CFM (@ 9:1 to Air-to-Cloth ration) but to do so will require slightly larger fan/motor. -- Needs new bags as they were discarded.

AIREWORKS FX15-5000 / 2XTB Modular VFD controlled Dust Collection System. The "FX" series is a self-contained modular designed unit for interior use utilizes a dynamically balanced fan. -- "TEFC" motors, precision Laser-Cut components, & multiple discharge options with standard being plastic bags. -- AIREWORKS own Cruise Control system and how it works... Multiple machines can be connected to a single FX collector. The following example shows several machines connected to FX15-5000.Each machine can be isolated by a slide gate when not in use. If machines 1 & 2 total 4,500CFM when they are in use, the sensor will request the Cruise Control software in the VFD to run the fan motor at the required speed to exhaust exactly 4,500CFM. The motor will in this case run at 55.9Hz and consume 11 HP. If machine (4) starts and machine (2) shuts down, then the exhaust requirement drops to 2,200CFM.The Cruise Control will now request the fan motor to spool down to 55Hz and the power consumption drops to 8.6HP. In this way the fan speed and power consumption will automatically be adjusted at all times to match the actual requirement. The built-in Cruise Control guarantee's that the suction is always constant at a minimum power consumption. -- Heavy Duty metal construction, fully welded plenum built using 11 Ga. steel. -- Rated at maximum 5,000 CFM pressure range from 8 - 12 IWG. Equipped with: -- (15) 8' tall High Efficiency filter bags up and (3) plastic collection bag down. -- The filter bags have 375 Sq. Ft. of cloth filter area and 21:1 air to cloth ratio with 33 Cu. Ft. of collection capacity. -- Direct drive dynamically balanced centrifugal fan assembly with 15 HP TEFC motor, 5,000 CFM, 1,750 RPM. -- Non-sparking Heavy Duty machined & balanced impeller; 15" inlet diameter. -- Manual motor starter for 230 V or 460 V. MUST SPECIFY.Includes: 2XTB Tipping Bin with (2) inlets. -- Forklift truck moveable with Locking wheels and railings instead of plastic collection bagsPHOTO DOES NOT REPRENSENT ACTUAL MACHINE

AIREWORKS FX-05-2000 Modular Dust Collection System. The "FX" series is a self-contained modular designed unit for interior use utilizes a dynamically balanced fan, "TEFC" motors, precision Laser-Cut components, & multiple discharge options.Features: -- "AIREWORKS" has over 20 years of applied experience in developing & building commercial dust collection systems. -- The "MOD-FLEX" technology designs are engineered for compatibility with today's modern work cell manufacturing environments & are expandable as your business evolves. -- Heavy Duty metal constructed plenum between the top bags and bottom dust collection; rated at 2,000 CFM / 7-10 IWG with 16.7:1 air to cloth ratio. Equipped with: -- (5) 12" x 6' High Efficiency filter bags up and (3) plastic collection bag down. -- The filter bags have 125 Sq. Ft. of cloth filter area and 16.7:1 air to cloth ratio with 40 Gal. of collection capacity. Complete with: -- Direct drive dynamically balanced centrifugal fan assembly with 5 HP TEFC motor, 1,750 RPM, non-sparking Heavy Duty machined & balanced impeller; 11" inlet dia. -- Manual motor starter for 230 V or 460 V. MUST SPECIFY.PHOTO DOES NOT REPRENSENT ACTUAL MACHINE

AIREWORKS FX-10-3500 Modular Dust Collection System. The "FX" Series is a self-contained modular designed unit for interior use that utilizes a dynamically balanced fan.Features: -- "TEFC" motors, precision Laser-Cut components, & multiple discharge options. -- "AIREWORKS" has over 20 years of applied experience in developing & building commercial dust collection systems. -- The "MOD-FLEX" technology designs are engineered for compatibility with today's modern work cell manufacturing enviroments & are expandable as your business evolves. -- Heavy Duty metal constructed plenum between the top bags and bottom dust collection; rated at 3,500 CFM / 7-10 IWG with 14:1 air to cloth ratio. Equipped with: -- (10) 12" x 8' High-Efficiency filter bags up and (2) plastic collection bag down. -- The filter bags have 250 Sq. Ft. of cloth filter area and 13:1 air-to-cloth ratio with 80 Gal. of collection capacity. -- Direct drive dynamically balanced centrifugal fan assembly with 10 HP TEFC motor, 1.750 RPM -- Non-sparking Heavy Duty machined & balanced impeller; 13" inlet diameter. -- Manual motor starter for 230 V or 460 V. MUST SPECIFY.PHOTO DOES NOT REPRENSENT ACTUAL MACHINE