FANUC M410/160 iB ROBOT PALLETIZING SYSTEM Specifications: -- Complete with R-30iA Controller All Refurbished -- Pillow Bag Tooling -- 4-Axis control -- Mounted to a heavy-duty base -- 10 Feet Long Rubber Belt Conveyor -- (2) 5 Feet Motorized Pallet Conveyor -- (3) 10 Feet Motorized Pallet Conveyor -- Automatic Pallet Dispenser -- up to (14) 50 Lbs bags per minute -- Machine weight 4500 LbsAUTOMATIC PALLET STRETCH WRAPPING SYSTEMWULFTEC or LANTECH Stretch Wrapping System or Equivalent Not INCLUDED

END ARM TOOLING FOR FANUC ROBOT -- Gripper Finger Type End Arm Tooling -- Design for Fanuc Robot Model S-430iW -- Loaded on your truck

FANUC - M-410I, ...Palletizing RobotFANUC M-410iC/110 Robot is a Palletizing Robot. It runs on the FANUC "R30iB" and "R30iB Plus" controller platform. With lighter payload, this Robot is designed to run faster than its bigger variants.This Robot was ordered and never installed, so it is "new" old stock.Max. payload: 110 kG (242 Lbs). -- Reach: 2,403 mm (94"). -- Axes: 4. -- Repeatability: +/- 0.5 mm. -- Robot Mass: 1,030 kG (2,270 Lbs). -- Floor mounted.

FANUC - S430iW, ...RobotFANUC Robot for palletizing rectangular compressed bags.Specifications -- (6) Axes. -- Payload: 165 kG (255 Lbs). -- H-Reach: 2,643 mm (104"). -- Robot mass: 1,300 kG (2,860 Lbs). -- Complete with: Pendant control. -- Complete with: Gripper type arm and pallet gripper. -- Refurbished with (90) days Warranty. -- Buyer to install safety guards.NOTE: Machine was rebuilt is 2021.

FCM 30HP Vertical Feed Hammer HogSpecifications:- Intake 14" X 18" -- Drive motor 30 HP -- Extraction 8" diameter -- Screen with 3/4" holes -- Magnetic starter

FLEXICON HOPPER/FEEDERSpecifications: -- Flexible Screw Approximately 12 Feet -- 7" Diameter -- Flights 6-1/2" -- Tube Diameter 7-1/2" -- Discharge Height 86 Inches -- Discharge Diameter 10 Inches -- 10 HP Motor -- Dimensions; 72" Long x 48" Height x 7-1/2" Depth -- Loaded on your Truck

FORESTECH ENTERPRISES - D-GR-1S: DryerDrum Dryer designed for a large Pellet plant; never put into production.Diameter (approx.): 12-3/4 Ft.Drum Length (approx.): 48 Ft.Dryer comes with Forge Tire but does not come with trunnion drives, which we can have manufactured.

GENERAL KINEMATICS Para-Mount II Single Deck Rectangular Vibratory Screener;Complete with the following features: --Model STM 96 X 20. --Carbon Steel. --Nominal screen size 96" wide x 20 long x 15" deep. --Designed for Trona mineral at a feed rate of 700 tons per hour at 80 pounds per cubic foot bulk density. --Driven by (2) 15 HP top mounted drives. --Current screen: Approximate 1" x 1" square openings. --Base mounted. --Overall dimensions: 290"L X 130"W X 90"H

GENOX V800 New Single Shaft ShredderIn Stock - Ready to Ship!Features: -- Shock Absorbing Gearbox that reduces stress on Drive Components -- 50 HP motor -- Hopper Opening - 59" x 56" -- Rotor Diameter - 15.75" -- Rotor Knives that can be used on four edges before replacement. -- Durable Counter Knives that adjust to maintain cutter clearance -- Quick Change Screens for accurate particle size control -- Segmented Shredding Chamber Floor with Brass Guides -- Twin Speed Hydraulics with an integrated air cooler -- Stand Alone Electrical Control Panel with Siemens PLC Control System -- Tested, Approved and Certified to the applicable CE safety standardsTypical Applications --Plastics --Wood --Cable --Paper --Aluminum --Foam --Textile

GENOX V600 New Single Shaft ShredderIn Stock - Ready to Ship!Features --Shock Absorbing Gearbox that reduces stress on Drive Components -- 25HP -- Hopper Opening - 48" x 43" -- Rotor Diameter - 9" --Rotor Knives that can be used on four edges before replacement. --Durable Counter Knives that adjust to maintain cutter clearance --Quick Change Screens for accurate particle size control --Segmented Shredding Chamber Floor with Brass Guides --Twin Speed Hydraulics with an integrated air cooler --Stand Alone Electrical Control Panel with Siemens PLC Control System --Tested, Approved and Certified to the applicable CE safety standardsTypical Applications --Plastics --Wood --Cable --Paper --Aluminum --Foam --Textile

GENOX GSX2260 Single Shaft ShredderFeatures --Shock Absorbing Gearbox that reduces stress on Drive Components -- 25HP -- Hopper Opening - 48" x 43" -- Rotor Diameter - 9"Typical Applications --Plastics --Wood --Cable --Paper --Aluminum --Foam --Textile

GRANUTECH-SATURN - 62-40, ...Dual Shaft ShredderSpecifications: -- Motors: (2) 100 HP. -- Feed Opening: 62" x 40". -- Dual Shaft with independent Driven Shafts -- Includes: Feed conveyor & discharge conveyor, extra feed hopper; an extra pulley roller that is magnetized for exit end of discharge conveyor (current pulley roller in use is nonmagnetic). -- includes: (2) Service manuals and catwalk structure.

GRANUTECH-SATURN - GRIZZLY 80, ...Grinder Granulator NO MOTOR, LID OR DRIVE TRAINSpecifications: -- Rotor size: 77-1/2" -- Cutting diameter: 34-1/2" -- Main motor: 300 HP -- Speed: 321 RPM -- Number of knives: 50 -- Number of stationary knives: 10 -- Rotor type: STAR

HAAS - 2000XL 2.0, ...Mobile ShredderLow Hours; 2018 YMFG.Specifications & Features: -- Can be used at any location (comfortable transport measurements). -- Easy & quick positioning thanks to crawler track and radio remote control. -- Shreds different materials with just (1) tool configuration. -- High throughput capacity of up to 100 tons/Hr. -- Resistant against foreign bodies. -- Low wear cost and long lifetime. -- Service and maintenance friendly. -- No wrappings; self-cleaning. -- Quiet main drive.

HAMMEL 750D HAMMERMILL NEW IN 2019Approx 3,000 Hours --Hydraulic recycling machine with 2 slow running tool shafts --Suitable for Wood (Old wood, construction & demolition wood, rhizomes, green waste, pallets, cable drums) or Rubbish (Domestic waste, industrial and commercial waste) and Paper, paper rolls, aluminum profiles and balesAdvantages: --Increased performance for more throughput --low energy consumption --Very easy to maintain --User-friendly handling by IFM control --Better accessibility of the control panels --Low noise --Tilt funnel with increased inclination for optimum material flow --Mobile on a chain or semi-mobile on a hooklift

HURST 600 HP Waste Fired Boiler; -- Specifications:Complete in-place system with the following features: -- Decommissioned July 2019. -- 150 PSI. (300 PSI max wp), -- 20,700 Lbs per hour. -- Fuel House, Boiler Building and all Controls -- System has been "pickled" to maintain tube integrity.

HURST - SERIES 45. Boiler: Natural Gas -- SpecificationsBuilt New in 2016; Complete, never installed & ready to deliver! 207.5 HP; 60 PSI Hot Water; Natural Gas Fired Firebox. -- Efficient 3-pass design NATURAL GAS FIREBOX. -- ASME Code constructed & stamped for 15 PSI Stream: 30 - 100 PSI Water. -- Registered with: National Board of Boiler Inspectors. -- Easily maintained, designed for efficiency; large Furnace volume for ultimate combustion efficiency. -- Unified refractory base floor; steel skids; lifting eyes. -- Low heat release; Factory insulated. – 2"; Mineral wool, Factory jacketed & painted. -- Easy access to fireside surfaces; ample waterside clean-out openings -- Fully automatic operation; U.L. listed; forced draft Burners. -- Wet back construction. -- U.L. Listed controls & trim. -- Factory test fired, flame observation ports front & rear.Boiler Design. 3-Pass “FireBox"; design with: Stress relieving “Wetback"; fire tube construction.Hot Water pressures models are from: 8.5 - 415 HP; 100 PSI max.; 500 - 813 HP; 60 PSI max. built to Section-IV ASME Code.Hot water temperature not to exceed 250° F at or near the outlet of Boiler.Hot Water Model Trim. Safety relief valve; operating temperature control; high limit temperature control with manual reset; combination pressure & temperature gauge; low water cutoff control with manual reset.Hot Water Supply. 180 D/F Return: 160 D/F. -- Fireside Heating Surface: 830 Sq/ft. Furnace volume: 132 Cu/ft. Hot water outlet: 8"; hot water drain: 6"; drain connection: 2".Burner: Matched UL listed “forced draft"; power burners with: Factory pre-piped, wired, and tested fuel configurations for natural gas, propane (LP) gas, No. 2 (diesel) oil, or combination of both gas/oil.All units are Factory packaged with: Operating controls, relief valves, burner, and fuel train. Installation is made simple in that only service connections are needed to place in operation.High density 2"; mineral wool insulation assures lower radiant heat loss. In addition to meeting the requirements of U.L., Burner Systems are optionally available to meet the requirements of FM, IRI, Military, and others. -- Actual model: HURST S45 – G – 207.5 – 60W

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

30-series hydraulic drive machine, with special-length 66" hopper box.Equipped with standard-gib heads, but can be upgraded to the Knife Cartridge System™.Factory-mounted diesel power unit for heads and hydraulic unit.Belt conveyor under shaving mills is 24 in. wide x 20 ft. long, installed under machine to discharge shavings out the end.Additional long outfeed conveyor (approximately 85 ft.) is included, along with 32 ft. log deck and knife sharpener.Will do about 20-25 yrs per hour

16" Used JMC MCINTYRE SHEARAn affordable efficient 407mm (16″) blade shear with enough power and speed to handle a wide variety of cutting tasksRobust, affordable, efficientBuilt originally for scrapyard use, the McIntyre 407 shear is robust enough to withstand the most difficult of working environments. It is now our most popular alligator shear with more than 2000 still in daily use worldwide. The McIntyre 407 is able to handle; automotive scrap, whole gear boxes, cylinder heads and blocks, oversized gate valves and of course all the usual non ferrous metal separations. The 407 can also be used to cut ferrous metals.Technical DataMachine dimensions: 1590 x 712 x 1350mmBlade Length: 407mm / 16";Tip to tip opening: 225mm / 8.8″Shearing height: 931mm / 36.6";Weight with oil: 900kgOil capacity: 200 Litres / 44 GallonsNoise Level: 75 +/- 3dBACut control: Single Cut repeatingStandard ElectricalRequirements: 32A / 3ph / 380-415v / 50HzPower Rating: 7.5 kW / 10hpMotor speed: 1450 rpmMax system Pressure: 214 Bar / 3100 psiMax Shear force: 120 TonnesFully open cut speed: 11 dry cycle cuts per min40% Stroke cut speed: 28 dry cycle cuts per minCutting Capacity: 56mm (2";) Round Bar / 45mm (1.5";) Square Bar