HOMAG KAR 310/6/A3/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Special "RIGHT-HAND" Feed HOMAG. -- Specifications:Working Capacity, 0.3 - 3 mm Edge thickness cap., min. panel width 55 mm; max. panel thickness 60 mm; feed speed variable from 18 - 25 MPM (59 - 82 FPM).Equipped with: -- Pre-Milling Unit: (2) Motors, 3 kW - 9,000 RPM each motor; pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator infeed fence. -- Hot Melt Glue System: Quick Melt Unit with reversible glue roller applicator. -- Edge Magazine: Automatic 1-Coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers. (1) Large dia. driven & (2) idle rollers; "NC" adjustment of pressure zone through the control for different edge thicknesses. -- Spraying Device: Top and Bottom spray nozzles for applying separating agent, for easier cleaning of any residual glue on panel.Workstations: -- End Trimming Unit: (2) Motors, 0.5 kW (0.7 HP) - 12,000 RPM each motor; cuts excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit - Top & bottom Trim Station, 1.5 kW (2.0 HP - 12,000 RPM) Motor; +/- 1° angle adjustment, manual positioning with digital counters. -- Profile Trimming/Corner Rounding Unit: (2) Multifunction motors to process the edge overhangs at the workpiece upper & lower edge, as well as trimming around the front & rear edge; (2) 0.55 kW (HP 0.73) each motor. -- Open Station: Open space of 23.6" (600 mm), for future installation of a working unit. -- Profile Edge Scraping Unit: Electro-pneumatic adjustment. -- Finish Process Unit with Glue Scraper + Buffing Unit: Flat top & bottom panel surface glue scraper & buffing, removes any potential squeezed-out glue residue.Operator & Machine Control: HOMAG "Power Control PC 22 + Windows "XP" operating System. Controller on separate console with 19" flat screen display, keyboard, and mouse. Includes fault diagnostic, OS9 real -time operating system. Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam, and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAR 310/6/A3/S2, Special "RIGHT-HAND" Feed Configuration HOMAG.

HOMAG EDGETEQ S-500 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.3 - 20 mm (0.011 - 7/8") Edge material thickness; 8 - 60 mm (0.3' - 2.375") panel thickness; 160 mm (6.375") min. panel length and 70 mm (2.75") min. panel width.High flexibility is achieved as all edge materials can be processed: 0.3 mm Melamine, up to 3 mm ABS, PP, PVC and wood as coil material.Solid wood strips and veneer strips up to 12 mm are fed in individually and up to 20 mm from the package. Even veneer strips of up to 1 mm can be fed from the package.For perfect high-gloss parts, important components such as the motor-driven top pressure and the automatic adjustment of the glue joint scrapers are used.Special tracing elements are ideal for processing of acute angled or obtuse angled parts or parts with hinge holes and transversal grooves.Variable Production Feed Speeds from 16 - 30 MPM (52 - 98 FPM). -- Equipped with: Separating agent spraying unit. -- Premilling Station: (2) Motors @ 2.25 kW (3.0 HP), 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Infeed fence with Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic Edge Magazine for strip & coil stock, strips 0.4 mm - 12 mm (0.015 - 0.47"), coils up to 3 mm PVC with "HD" guillotine. -- "Quick Change" Glue Tank for maintenance, glue type & color change. -- Pressure Section: 1st. Roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- HOMAG "PowerTouch control, memory: 256 MB RAM, 1 GB Flash Card Drive. -- Workstations: End Trimming: (2) Motors @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Multistage MS40 Flush/Bevel-Fine/Radius Trimming Unit:Top/bottom: (2) Motors, 0.55 kW (3/4 HP) - 12,000 RPM, auto-tilt positioning 0° - 25°; with combination flush/radius/chamfer cutterheads. -- Multifunctional trimming unit MF60 Servo trim - Horizontal and vertical tracing wheels, equipped with brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes (3) positioning options: Profile 1, profile 2, and flush trimming; nested top copy system. -- Corner Rounding Unit: (1) 0.35 kW (1/2 HP) - 12,000 RPM Motor for leading & trailing edges, vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, multi-profile (PVC): Top/bottom with (2) profiles (1 mm and 2 mm or 3 mm instead of 2 mm), Servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Flat Glue Joint Scraping Unit: Flush top/bottom on panel surface with floating insert knives. -- Buffing Unit: Top & bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. -- Operator Control: HOMAG powerTouch2 control with clearer structure, 30

HOMAG - AMBITION 2262 (KAL 210), ... PRODUCTION Edgebander (w/Premill & Corner Rounding): -- Specifications: Working Capacity: Coiled stock min./max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"); strip material min./max. Edge Thickness 0.4 - 6 mm (0.16 - 0.234").Panel stock min./max. thickness 12 - 40 mm (0.472" - 1.574"). Panel Overhang 30 mm (1.18"). -- Infeed Fence:Adjustable infeed fence with manual digital indicator positioning. -- Premilling Station:(2) 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with: Trimming column, (2) horizontal & cross-slides with spindle adjustment.Electropneumatic horizontal jump movement of the 1st motor; includes electronic frequency inverter for control of motor speed and braking.(2) Dust extraction hoods, air jet panel blowoff device & SIKO digital counters for adjustments. -- Panel Preheater:Preheating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multipurpose Magazine:2-Coil magazine expands capability by running coiled material, strips, and solid wood bands. Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table allowing the Operator to center the panelon the edgeband. -- Premelting System: Overhead Premelting Unit -- Gluing System: EVA - Hot Melt.QA 34 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allow for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates.Lower melting unit equipped with: Automatic glue level control; melting capacity: 12 kG/h (26 Lbs/Hr). -- Pressure Section:Manual adjustment with digital counter: (1) Large 160 mm dia. driven & (6) 70 mm dia. idle rollers; pneumatic pressure control depending on edgbanding material used.WORKSTATIONS: -- End Trimming Unit:(2) 0.8 kW (1.0 HP) - 200 Hz, 12,000 RPM Motors to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Rough/Pretrimming Unit:Top & bottom, (2) 0.55 kW (0.74 HP) - 12,000 RPM motors; height adjustment with the top pressure beam and tilting range +/- 1°. Manually adjusted with digital counters. -- Multifunction Profile/Bevel/Corner Rounding Unit:Multifunction (2) 0.4 kW (0.54 HP) - 12,000 RPM Motors to fine trim the edge overhangs at the workpiece upper & lower edge, as well as trimming around the front & rear vertical edge; Servo controlled.Max. feed speed 0f 20 MPM (65.6 FPM) when corner rounding. -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit:Top & bottom edge buffing/polishing. -- Sprayin

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor;Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG KAL 310/3/A3 Edgebander ... High Production - aka Tape Rocket -- Working Capacity:0.4 - 3 mm Edge thickness cap., min. panel width 55 mm; max. panel thickness 55 mm; Feed speed variable up to 18 to 32 MPM (59' to 104' FPM).Equipped with: -- Vertical Coil Tape Magazine; (2) positions, SIKO digital adjustments. -- Glue System "A34", hot melt with reversible glue roller applicator; -- Side Pressure Section with (1) large dia. driven & (2) idle rollers; manual adjustment of pressure zone through SIKO digital counters for different edge thicknesses. -- HOMATIC "PC 21" Controller features, function in Windows environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem.Workstations: -- End Trimming (2 x 0.25 HP - 200 Hz, 12,000 RPM each) to cut excess edge on the front & back of the panel. -- Trimming Station, top & bottom 2 x 1.0 kW (1.35 HP - 12,000 RPM). --÷ Buffing Unit, top & bottom 2 x 0.25 kW - 2,850 RPM each motor.Complete with & Features: -- Electronic DC Brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- Feed Track Pads 80 mm wide; manually adjusted -- V-groove belt on top pressure beam and Sound/Safety enclosure over workstations.

HOMAG OPTIMAT KL-75 / A20 EDGEBANDER 0.4 - 20 mm (3/4") Thickness edgebanding cap., 70 mm min. panel thickness.Equipped with: Automatic edge feed magazine for coil, HPL & strip stock; "Hot Melt" glue system with QA34 Quickmelt unit, with reversible glue roll applicator; pneumatically controlled pressure roll section with 7 pressure rollers. -- Workstations: Double motor front & rear end trim, straight & chamfer trimming (0.5 HP - 10,400 RPM ea. motor). -- Top & Bottom rough trims (2 HP - 11,500 RPM ea. motor). -- Top & Bottom fine trims, tiltable 0° - 30° (0.5 HP - 10,980 RPM ea. motor); open space for workstation. -- Adjustable top and bottom glue scraper. -- Electronic Height adjustment for Top pressure beam with double V-belts, 80 mm wide Heavy Duty feed chain w/rubber pads. -- Feed speed variable up to 35 MPM. -- Complete with: SIKO Digital adjustments on T & B Flush and Fine Trim. -- Homatic NC21 Controller, Fixed position Outrigger panel support, insulated sound cabins w/interior and overhead lighting for all trim workstations. -- Includes Owners Manual and the Electrical Schematics.NOTE: Suggested replacement parts needed, as noted by our technician - all the track pads, the hold-down belt, the pressure roller, and likely a glue pot rebuild. Estimated cost for these parts, not including labor is $5600. The replacement of these parts is NOT included in the machine price.

HOMAG KL 78/A20/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: 0.4 - 20 mm ( 0.02" - 0.78") Edge thickness cap., min. panel width 55 mm (2.18") for panel thickness 12 - 22 mm (0.5" - 0.875") and under; 100 mm (3.9") for panel thickness over 22 - 60 mm (0.875" - 2.3"); for up to 3 mm Coil stock, HPL, and strip stock up to 20 mm (0.75").Feed & Infeed Section of Machine: -- Top pressure beam with: Double-wide compound V-belts; 80 mm wide feed track chain plates, vulcanized rubber insert pads, and Auto-Lube; variable feed speed from 18 - 24 MPM (59 - 79 FPM); 950 mm height/working level infeed. -- Pre-Milling Station with: (2) 3 kW - 150 Hz, 9,000 RPM Motors, panel blow-off device; 2-position infeed fence (on/off), SIKO digital manual fence control. -- Panel Pre-Heater with: Quartz lamp for heating substrate edge before glue application. -- Edge Feeding device equipped with: Automatic coil magazine for quick coil changeover; strip feeder for up to 20 mm (3/4") solid wood banding. -- "Quick Melt" Glue System with: Reversible glue roller applicator; pressure roll section with (1) large dia. driven and (6) idle rollers; manual adjustment of pressure zone through SIKO digital counters for different edge thicknesses.Edgebanding Workstations: -- Double motor front & rear end trim, straight & chamfer trimming (0.8 HP - 12,000 RPM ea. motor). -- Top & Bottom flush trim (2 HP - 12,000 RPM ea. motor). -- Corner rounding unit: Equipped with (4) motors, 2 HP - 12,000 RPM each motor. -- Universal Milling/Grooving Unit tiltable 90°. -- Edge Scrape Super-Finishing unit for thick PVC/ABS with chip collection box. -- Top & Bottom Flat Glue Scraper to remove potential glue squeeze-out. -- Top & Bottom oscillating buffing unit (two 0.33 HP - 1,650 RPM motors). -- "HOMATIC NC 21" controller features with Keypad & LCD display, stores working programs and controls functions of workstations, allows fault diagnostic and more, etc. -- Complete with: PLC controlled, motorized beam height adjustment; servo adjustments on Top & Bottom flush trim, and servo controlled Scraper Stations. -- Electronic DC brakes on all trim motors, sound cabins for all trim workstations, and adjustable outboard panel support. -- Actual Model is HOMAG KL 78/A20/S2.

HOMAG AMBITION 2270 (aka KAL 210) Edgebander with Pre-Milling & Corner Rounding:Specifications & Features: 0.4 - 3 mm Edge thickness cap., min. panel width 55 mm (2-1/8") for panel thickness 12 - 22 mm & under; 100 mm (4") for panel thickness over 22 - 60 mm.Variable feed speed from 8 - 25 MPM (59 - 79 FPM); 80 mm feed trackpads, and V-groove belt on top pressure beam which is motorized; motorized raising & lowering of top pressure beam through program selection.Pre-Milling Station with: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with panel blowoff device and SIKO digital counters for adjustments. Edge Feeding Device with: 2-Coil vertical magazine for quick coil changeover.Gluing System suitable for PUR & reg; with: Pre-melt hopper feeder & roller applicator (reversible). Servo Controlled Pressure Roll Section with: (1) Large 150 mm dia. driven & (6) idle rollers; automatic Servo adjusting pressure zone through the program for varying edge thicknesses.Workstations:Double Motor End Trimming: 0.18 kW (0.24 HP) - 200 Hz, 12,000 RPM Motor ea.; to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip.Top & Bottom Flush Trim Unit with: Height adjustment with the top pressure and swiveling range +/- 1° (2 HP - 12,000 RPM ea. motor). Profile Trimming Unit with: (2) Motors to process the edge overhangs at the workpiece upper and lower edge, as well as trimming around the front & rear edge (0.75 HP motor ea.). (4) Motor Corner rounding station.Edge Scrape Super Finishing Unit for thick PVC/ABS. Top & Bottom Oscillating Buffing Station.

--at Auction, Seller Loading, Good Condition-- HOMAG KAL 310/4/A3/S2 Edgebander, with Pre-Mill Specifications: - Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed Equipped with: - Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. - Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; - Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. - Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges - HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. Workstations: - End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. - Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. - Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters - Profile Edge Scraping Unit: with electro-pneumatic adjustment - Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM Complete with & Features: - Electronic DC brakes on all trim motors; sound cabin for all workstations. - Adjustable outboard panel support with swing out arms for up to 800 mm. - 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. Note: This machine has a new display and a new back up one as well!

HOMAG EDGETEQ S-200 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + EVA/PUR + "AirTec" Technology: -- Specifications:0.3 - 3 mm (0.016 - 0.11") edge; 8 - 60 mm (0,312 - 2.375") panel thickness; 160 mm (6.375") min. panel length and 70 mm (2.75") min. panel width.Equipped with: -- Separating/cleaning agent spraying units. -- Pre-Milling Station, (2) motors @ 2.25 kW (3.0 HP), 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. --100 mm dia. diamond cutter heads. -- Integrated heated glue roller. -- AirTec reactivation unit for zero edge finish. -- Automatic Edge Magazine, for strip & coil stock, up to 3 mm PVC. -- "Heavy Duty" guillotine. -- EVA/PUR "Quick-Change" glue pot and roller application unit. -- Pressure Section, 1st. roller driven plus (2) idle rollers, timed pneumatic pressure controlled. -- Feed Speed, 8 MPM. (26 FPM). Operator Interface: -- HOMAG "easyTouch" Operator Interface with 7" graphic color touch display & soft keypad. Intuitive, user-oriented navigation.20 storable programs guarantee flexibility when processing a wide variety of edge materials and changing customer requirements.Clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain textWorkstations: End Trimming: - (2) Motor @ 0.35 kW (1/2 HP) 12,000 RPM, automatic chamfer from control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: - Top/bottom (2) motors, 0.55 kW (3/4 HP) 12,000 RPM, auto tilt positioning from control panel 0° - 25°, with combination flush/radius/chamfer cutter-heads.Includes (3) positioning options, profile 1, profile 2, and 3 flush trimming. -- Corner Rounding Unit: (1) Motor 0.35 kW (1/2 HP) 12,000 RPM, with automatic adjustment from control panel for 1-mil, 2-mil & 3-mil thickness.For leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, Multi-Profile (PVC): Top/bottom with (2) profiles. 1 mm and 2 mm or 3 mm in place of 2 mm positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Buffing Unit: - Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. Complete with:Motorized hold-down pressure beam; padded sound enclosure, isolation transformer for multiple input voltages, used tooling and Original Factory machine documentation. -- Actual Model is HOMAG EDGETEQ S-200 (aka OPTIMAT KDF 1130 AT).