#110 • 2018 Cleereman 3HB Carriage (1st of an entirety) SN: 38-1078-16, Model: 38, 110V over air controls, 7'6" x 14' overall dimensions, wheels 54" center to center, pantograph arms, Brownsville turners, track oiler

#200 • Cornell Single Arbor Edger-Gangsaw Model: E760, SN: E760-0016-97, 2 moving saws, 60" wide infeed, edger 28" wide, gangsaw 28" wide, 3 1/2" collars, 2" collars, 1 1/2" collars, 1 1/4" collars, side press roll on gang side, control box, no power, 6" x 16' tailing belt on edger side, 27" x 16' tailing belt on gang side

#100 • 2000 HMC V216 Rosserhead Debarker Model: V216. SN: 1740-00. Drive on the head: Electric. Head type: Steel. Width of head: 12". Debarker HP: 40hp electric. Chain drive: hydraulic power. Includes barn sweep: No. Pantograph: Cable. Cab: Yes, size: 4' x 4'. Controls: Yes, type: Pilot Joystick plus lever and foot petals. Features and Notes: Will be using till sale time, 14' outside of wheel, no support structure, slant track.

#256 • CAT 926E Wheel Loader SN: 94Z03144. Meter reads: 40,830 hours. Engine: 4 cylinder CAT. Fuel type: Diesel. ROPS: Enclosed cab. 3rd Valve: Yes. Center to center of pins: 27". Tire Size: 17.5-25. Attachments: Grapple forks, 6" x 42" forks, 80" wide. Heater: No. A/C: No. Quick Attach: No. Features and Notes: Has AC unit-condition unknown. Front passenger tire is not mounted to rim, will need to be repaired before loading or operating. Starts and runs

#128 • Corley 648 Edger SN: EH-648-016 (8687), 8" x 48" capacity, 80" x 9'6" infeed rolls with 3 strand 2-way transfer, air cylinders on pop-ups control panel, has laser lights, 60 hp electric motor, (2) 18" blades 1 moveable, includes electrical control panel, 6" x 24' tailing belt

#121 • Cornell Edger Gang Saw SN: HD4267035, SN: HD42670352-01, 21" edging capacity, 2 moving saws, 20" saws, only used as edge, 4' x 7' infeed table, 5" x 9' tailing belt with side drop, 2 laser lights, control box, hydraulic drive, support to ground

#115B • Detroit Diesel Series 60 Power Unit Meter reads: 9,810 hours. Control box in sawyer cab, electronic controlled, PEC clutch model CB3-14-A32X

#127 • 2022 Helle Double End Trimsaw SN: 202062, 1 moving saw, computer set, hydraulic on saws, 24" x 25' scrap belt, 7" x 18' capacity, includes stairs and platform

#1350 • Hyster H60XM Forklift SN: H177B55473C. Meter reads: 1,927 hours. Engine: Perkins. Fuel type: Diesel. Load capacity: 5,500 lbs. Stage mast: 3. Mast height: 83". Side shift: Yes. Fork positioner: No. ROPS: Enclosed. Tire size: (front) 28 x 9-15, (rear) 6.50-10. Tires: Solid. Features and Notes: 5" x 42" forks. Contact Daniel Miller with any questions 440-321-5965

#3550 • Ingersoll Rand Air Compressor Model: IRN20H-TAS. Screw type, 75 cfm 380/460V 3 phase. Was working when disconnected 3/20/24. Contact Daniel Miller with any questions 440-321-5965

#127 • McDonough 6' Line Bar Resaw with Runaround Entirety of Lots 118-126 With 10% raise.

#134 • 2022 Morbark Mulch Hog Grinder SN: 562-059, model: HD30, 34" x 10' vibrating in feed driven from conveyor, hydraulic drive on feed roll, no power, control box, hydraulic pumps, hydraulic tank and hoses

#133 • Newman 8 Head Drop Tim Saw Missing 1 head, 20" blades, 7 1/2 hp electric motor on each head, 20' board length max, 9' x 25' overall, control panels, 30" x 16' slide pan

#104 • Salem 3 HB Carriage and Track (1st of an entirety) SN: 501068-98, 90" x 16', 4 axle, 1st HB to 2nd HB-7', 2nd HB to 3rd HB-4', 1" dogs, tong dog, air dogs, air over 110 setworks, includes controls and electrical panel in cab, pantograph, track is 60" center to center, 60' long, includes support steel under track to ground

#1000 • Toyota 7FGU30 Forklift SN: 60267. Meter reads: Unknown. Engine: Toyota. Fuel type: LP. Load capacity: 6,000 lbs. Stage mast: 3. Mast height: 90". Side shift: Yes. Fork positioner: No. ROPS: Open. Tire size: 28x9-15, 6.50-10. Tires: Solid. Features and Notes: Gauges not workin, park brake not working. Runs and operates.